|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
May 11, 2020, 04:05 PM | #1 |
Junior Member
Join Date: May 10, 2020
Posts: 5
|
Pietta 1851 Navy Bolt Screw Coming Out
I, had a question about my recently bought Pietta 1851 Navy. When I work the action of the revolver and go to de-cock the hammer I notice that the Bolt screw wants to screw itself out of the revolver. I have never shot it and it’s brand new. Could this just be caused by the screw not being tight enough from the factory? The reason I haven’t tried to tighten it yet is because I do not have the correct screw driver tips and don’t want to damage the head.
|
May 11, 2020, 05:19 PM | #2 |
Senior Member
Join Date: February 24, 2013
Posts: 584
|
When you get a good screwdriver open it up and clean out the factory "shipping grease" out and oil with non-petroleum oil. check for any burs on the bolt and every thing else. If it still moves when oiled properly you can clean the threads and put a little finger nail polish on the threads.
|
May 13, 2020, 05:36 PM | #3 |
Junior Member
Join Date: May 10, 2020
Posts: 5
|
Thanks for the info. I'm going to get a Colt SAA Screwdriver kit from Brownells. People in reviews say it has all the bits to take one apart. I'm hoping it is just a lose screw.
|
May 13, 2020, 06:04 PM | #4 | |
Staff
Join Date: September 25, 2008
Location: CONUS
Posts: 18,468
|
Quote:
Don't buy any Grace screwdrivers to work on guns.
__________________
NRA Life Member / Certified Instructor NRA Chief RSO / CMP RSO 1911 Certified Armorer Jeepaholic |
|
May 13, 2020, 06:28 PM | #5 |
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,838
|
The Grace set I bought were hollow ground only at the tip.
I bought a bunch of used screw drivers from pawnshops (flea markets/garage sales can be good too) and ground them down to fit specific screws. I remember spending $45 for a toolbox filled with tools too.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
May 14, 2020, 07:02 AM | #6 | |
Junior Member
Join Date: May 10, 2020
Posts: 5
|
Quote:
|
|
May 14, 2020, 09:07 AM | #7 |
Staff
Join Date: September 25, 2008
Location: CONUS
Posts: 18,468
|
Good. The tips in that set are hollow ground. Much better than the Grace.
I am amazed that Brownells still sells the Grace screwdrivers.
__________________
NRA Life Member / Certified Instructor NRA Chief RSO / CMP RSO 1911 Certified Armorer Jeepaholic |
May 28, 2020, 11:40 PM | #8 |
Member
Join Date: December 3, 2008
Posts: 50
|
Sounds like your 51 needs to be debarred. You probably have a burr on your hammer that's binding on your hammer screw. Remove your hammer and look for machine burrs on the screw holes check the hole for the hand as well. I chamfer holes with a drill bit a few sizes bigger than the holes. also, look for burrs on the trigger screw. A few hours with a small file set will pay dividends your revolver will run much smoother and it will make your internals last a lot longer. Go to youtube and watch some videos and you be able to do it yourself. I bought the Brownell SAA bit set only two of the bits fit BP revolvers and one of them I had to narrow up on a belt sander. As someone else posted I bought a few small screwdrivers that I liked and grown to a nice fit. At the range, I use one of these screwknifes that I made myself. https://www.redwingtradingcompany.com/shop I reprofiled an Opinel knife and grown the tip to fit revolver screws. https://www.ebay.com/itm/Opinel-No-8...ss!95356!US!-1 They work great for cap jams.
51 |
May 29, 2020, 03:51 PM | #9 |
Senior Member
Join Date: October 24, 2008
Location: Naples, Fl
Posts: 5,440
|
Some years ago, I made these screw drivers.
It is five different sizes to match all of the screws I encountered at that time.
Handles are oak. Shanks are steel and the tips are hollow ground bits from a set something like a Chapman set. Heat shrink tubing protects the finish in case I slip.
__________________
Seek truth. Relax. Take a breath. |
May 29, 2020, 06:08 PM | #10 |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,189
|
If you slip it's going to be the edge of the blade going across your gun. Just sayin.
|
May 29, 2020, 08:15 PM | #11 |
Senior Member
Join Date: October 24, 2008
Location: Naples, Fl
Posts: 5,440
|
As usual...
You are correct, Hawg. But that would be true for any screw driver.
The heat shrink just keeps the bulges and bumps on the screw driver from contacting the finish if I slip. I didn't mention this but the presence of the heat shrink also allows me to use the screw drivers as prying tools (in the unusual event that is needed) without marring the finish. The screw driver bears against whatever is being moved on the heat shrink covered surface rather than on metal.
__________________
Seek truth. Relax. Take a breath. |
|
|