The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Tactics and Training

Reply
 
Thread Tools Search this Thread
Old August 21, 2018, 11:00 AM   #26
Fishbed77
Senior Member
 
Join Date: November 23, 2010
Posts: 4,412
Quote:
Ricochets, sparks and wildfires comes to mind.
If a bullet doesn't attract a magnet (jacketed lead for example), there should be no concern of sparks or wildfires.

If a quality target is properly mounted and the shooter is the correct distance away, there is should be no concern of ricochets. Common sense has to be used with steel targets.
Fishbed77 is offline  
Old August 21, 2018, 01:31 PM   #27
Bill DeShivs
Senior Member
 
Join Date: April 7, 2006
Posts: 9,649
Incorrect. If the target is hit hard enough, the steel itself will spark.
Try abrading a piece on a bench grinder.
__________________
Bill DeShivs, Master Cutler
www.billdeshivs.com
Bill DeShivs is offline  
Old August 21, 2018, 01:49 PM   #28
LineStretcher
Senior Member
 
Join Date: June 14, 2018
Posts: 240
Quote:
Originally Posted by Bill DeShivs View Post
Incorrect. If the target is hit hard enough, the steel itself will spark.
Try abrading a piece on a bench grinder.
I believe this is correct except that you must actually remove a piece of the steel to create the spark. High carbon steel is less likely to have a piece removed but if you accomplish that it will be more likely to create a spark. The grinder test is a good example of that. Low carbon steel sparks very little and clogs up your grinding material fast while high carbon steel sparks a lot and wears down your grinding material fast.
LineStretcher is offline  
Old August 22, 2018, 08:25 AM   #29
jmorris
Senior Member
 
Join Date: November 22, 2006
Posts: 2,958
You guys might be interested in this video.

https://www.youtube.com/watch?v=QfDoQwIAaXg

Watch the beginning for a minute with “soft” steel and note the “splash” of the impacts. Then move to 8:00 in or so and you can see the difference when using steel that stays flat as the bullet impacts when instead of a splash, you get a radial pattern.
jmorris is offline  
Old August 23, 2018, 09:14 PM   #30
RedHoundTargets
Member
 
Join Date: January 7, 2018
Location: Connecticut
Posts: 34
First and foremost you want that flat surface others have mentioned. Next up is a downward angle (the bottom of the target farther from the shooter), and finally, the ability for the target to swing (though not as important). Rounded, or pitted surfaces lead to all kinds of wonky stuff going on at impact so its much more likely to lead to a ricochet coming back to the firing line.

The AR_ family of steel was originally made for mining and construction equipment so there's a chance those teeth actually are an AR type steel. But for the reasons mentioned above its not ideal to be shooting at them.
__________________
Red Hound targets.
Steel targets made in the USA.
www.redhoundtargets.com
RedHoundTargets is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:20 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05735 seconds with 9 queries