The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools Search this Thread
Old February 24, 2018, 05:43 PM   #1
loademwell
Senior Member
 
Join Date: November 6, 2012
Posts: 164
Screws for guns.

OK... I am a small town gunsmith and it seems that I have so many guys bringing in older guns (grandpas) and its missing one screw.
Prime example, I Have a Bursa 9mm (think its a bursa P9 or something like that, Its in the shop). Anyhow, He only wants one screw replaced on the rear sight. (It really is just one screw) I went through all of my grab bag of parts and I don't have one screw that seems to fit it. 8x32 is about as close as I can go but its not going in.

Main question is:
Is there a way to get the right screw from the net or somthing and how do you go about ordering it?

Or can a fellow smith pull that one screw and give me the measurements?
Hate to retap it when the threads are fine.

Thanks
loademwell is offline  
Old February 24, 2018, 07:24 PM   #2
tangolima
Senior Member
 
Join Date: September 28, 2013
Posts: 3,769
The screw is likely metric. Try M4.

-TL

Sent from my SM-G930T using Tapatalk
tangolima is online now  
Old February 24, 2018, 11:57 PM   #3
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 21,824
Brownells has that box o' screws. You may want to buy that.

I tried restoring a museum owned old percussion fired double barrel. The hammer screw was missing so I tried to fit it. Not American, not metric. I couldn't even make a new screw on a lathe if I wanted to. I finally made a dummy screw and waxed it in place. It was a display piece only.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is offline  
Old February 25, 2018, 12:27 AM   #4
tangolima
Senior Member
 
Join Date: September 28, 2013
Posts: 3,769
Some guns use non-standard threads. The mosin rifle action screws are one example, if I remember correctly. You are mostly out of luck if you can't find the exact replacement, or aren't able to make one.

-TL

Sent from my SM-G930T using Tapatalk
tangolima is online now  
Old February 25, 2018, 03:55 AM   #5
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
You can order just about any screw you need on the internet. Try ebay.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Scorch is offline  
Old February 25, 2018, 04:58 PM   #6
tangolima
Senior Member
 
Join Date: September 28, 2013
Posts: 3,769
Quote:
Originally Posted by Scorch View Post
You can order just about any screw you need on the internet. Try ebay.
You can't unless you know the thread size.

-TL

Sent from my SM-G930T using Tapatalk
tangolima is online now  
Old February 26, 2018, 11:42 AM   #7
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
Quote:
You can't unless you know the thread size.
True. But if he can't figure out how to measure thread pitch, he is in way over his head.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Scorch is offline  
Old February 26, 2018, 12:23 PM   #8
tangolima
Senior Member
 
Join Date: September 28, 2013
Posts: 3,769
Quote:
Originally Posted by Scorch View Post
True. But if he can't figure out how to measure thread pitch, he is in way over his head.
It is much more difficult to find the thread specs when you are given a threaded hole. Trying a bunch of bolts is the first to do, and the op did that. If none fits, you try searching and asking on internet (op did that too).

I probably will bring the part to a industrial hardware supply store, where they have standard threads of all sorts, and try it there. Things start to go exponentially more difficult from there. There are ways, but just time consuming, and/or expensive.

-TL

Sent from my SM-G930T using Tapatalk
tangolima is online now  
Old February 26, 2018, 12:45 PM   #9
FITASC
Senior Member
 
Join Date: December 6, 2014
Posts: 6,432
Quote:
The screw is likely metric
My bet for correct answer
__________________
"I believe that people have a right to decide their own destinies; people own themselves. I also believe that, in a democracy, government exists because (and only so long as) individual citizens give it a 'temporary license to exist'—in exchange for a promise that it will behave itself. In a democracy, you own the government—it doesn't own you."- Frank Zappa
FITASC is offline  
Old February 26, 2018, 09:11 PM   #10
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
Quote:
It is much more difficult to find the thread specs when you are given a threaded hole.
I am aware of this, I fix guns for a living. And I have to find thread pitch for blind holes with alarming frequency.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Scorch is offline  
Old February 27, 2018, 01:45 PM   #11
T. O'Heir
Senior Member
 
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
Mosin rifle action screws are metric. Mind you, there's more than one standard for metric stuff. Mosin/Russian vintage stuff may not be the same metric standards as other metric standards. Absolutely will not be 8-32. That's UNC/UNF Unified Thread Standard.
These guys do Bersa parts.
https://bersa.eagleimportsinc.com/bersa/contacts/
__________________
Spelling and grammar count!
T. O'Heir is offline  
Old February 27, 2018, 07:21 PM   #12
tangolima
Senior Member
 
Join Date: September 28, 2013
Posts: 3,769
Quote:
Originally Posted by T. O'Heir View Post
Mosin rifle action screws are metric. Mind you, there's more than one standard for metric stuff.
Not all of them. A lot of them are #15-32, a special thread, non-metric though.

-TL

Sent from my SM-G930T using Tapatalk
tangolima is online now  
Old February 28, 2018, 02:33 PM   #13
tobnpr
Senior Member
 
Join Date: August 1, 2010
Location: Tampa Bay
Posts: 4,556
^^^ and the barrel tenons are standard 16p, V-thread....
__________________
Remington 700/Savage Rebarreling /Action Blueprinting
07 FFL /Mosin-Nagant Custom Shop/Bent Bolts
Genuine Cerakote Applicator
www.biggorillagunworks.com
tobnpr is offline  
Old March 1, 2018, 08:04 PM   #14
Reloadron
Senior Member
 
Join Date: June 8, 2016
Location: Cleveland, Ohio Suburbs
Posts: 1,750
A good start is:
Numrich Gun Parts: Gun Parts & Firearm Accessories
My next stop is as mentioned Box O Screws from Brownell's and Brownells also offers screw blank kits so you can literally roll your own screws in assorted sizes and thread. That includes US as well as Metric threads.

Ron
Reloadron is offline  
Old March 6, 2018, 10:01 AM   #15
paknheat
Senior Member
 
Join Date: October 17, 2006
Location: East Texas
Posts: 334
You can try Jack 1st also.

I’ve had good luck with them finding odd ball parts.


Sent from my iPhone using Tapatalk Pro
paknheat is online now  
Old March 6, 2018, 01:53 PM   #16
JeepHammer
Junior member
 
Join Date: February 27, 2015
Posts: 1,768
This should be common knowledge for gunsmiths...

Before WWII there was no 'Standard' or 'Common' thread types.
During the 'Punitive Expedition' & WWI every company had its own threading for fasteners.
Early Colt revolvers are Ely Whitney threading, since Ely Whitney provided tooling & machining for Colt.

Cadillac, FWD, Ford and all other makers had their own threads on fasteners, which the military ran into during WWI and specified a chart of 'Common' thread types during WWII to avoid the headaches again.

Brown & Sharp was probably the most common threading before WWII simply because they made a ton of tooling used in industral applications...

There is a reason 'Gunsmith' tools are specialized, not even common screwdriver blade widths & thicknesses are common to everyday fasteners.

Now,if you are going to 'Gunsmith' without a formal education, particularly if you are going to work on pre WWII firearms, consider finding a clock/watchmaker/gunsmith screw cutting lathe.
These are normally hand powered and since you won't find a modern one it will have a bunch of the old thread cutting tools.
You can expand on the kit by picking up thread cutting tools from broken sets as you find them...
After about 30 or 40 years you will find cutting tools to makes about 70% of the threads you will run into.
The rest you have to make the tools to cut the threads as you run into them...

European firearms (with the exception of English) will have something based on the metric system, more than likely... (No guarantees)

Your average modern screw cutting lathe will do about 20% of firearms made before WWII.
There is a reason gunsmiths have very old machines they keep rebuilding, they will often cut 50-60% of screws you run into.
Then you have to find the gears to drive the cradle, which sends you on endless junk store, eBay & used machine tool broker searches...

Brownells has a 'Grab Bag' of 'Gun Screws', and sometimes places like Numrich Gun Parts will have the part you are looking for. https://www.gunpartscorp.com
Be prepared for disappointment & frustration if you don't have an exploded view & part number, which Numrich has THOUSANDS of to search.
JeepHammer is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:23 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.11764 seconds with 10 queries