August 27, 2005, 08:09 PM | #1 |
Member
Join Date: August 5, 2005
Posts: 46
|
Profile Crimp die help
Just bought a new Redding Profile Crimp die 38/357. This die does nothing but a light roll crimp. There is no resistance in the press handle at all until you hit the roll crimp portion of the die. In fact, if you remove the die from the press and invert it, a resized case with a 148 wadcutter fully seated will fall into it until it hits the roll crimp shoulder. Bad die from the maker? Thanks for any help you can give.
|
August 28, 2005, 08:19 AM | #2 |
Senior Member
Join Date: June 21, 2002
Posts: 2,019
|
Tom, what exactly do you want the die to do that it isn't doing now?
|
August 28, 2005, 08:40 AM | #3 |
Senior Member
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,324
|
dozen
Doesn't sound right; should be a taper leading up to the roll.
Bad die? Flare a 357 case then run it through the Redding; what does it look like?
__________________
. "all my ammo is mostly retired factory ammo" |
August 28, 2005, 08:53 AM | #4 |
Member
Join Date: August 5, 2005
Posts: 46
|
Profile Crimp die problem
It was my understanding these dies put a combination taper and roll crimp on the bullet. This die only does a slight roll crimp. There is no evidence whatsoever of any taper crimp being applied. If I were to take a flared case and run it through the die, there would be a roll crimp applied, but no taper at all. It would look like any other roll crimped case with a light to moderater roll crimp. Thanks again for the help, this one has me stumped.As Weshoot II said there should be a taper leading to the roll crimp and I can find no evidence of this being the case.
|
August 28, 2005, 09:11 AM | #5 |
Senior Member
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,324
|
more testing
Okasy, now apply a nearly-case-crushing heavy roll crimp on an empty case; what does that look like?
__________________
. "all my ammo is mostly retired factory ammo" |
August 28, 2005, 09:24 AM | #6 |
Member
Join Date: August 5, 2005
Posts: 46
|
Profile crimp help
Weshoot II - I stuck a R-P brass (not plated) case in the press and adusted it as you asked. It gives the mouth of the case a bottlenecked appearance much like any other bottlenecked case but to a lesser degree. The reduced diameter band at the case mouth is about 1/16" wide. Hope this helps, Tom
|
August 28, 2005, 09:27 AM | #7 |
Senior Member
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,324
|
bad
Send it back; get another.
__________________
. "all my ammo is mostly retired factory ammo" |
August 28, 2005, 09:35 AM | #8 |
Member
Join Date: August 5, 2005
Posts: 46
|
Profile Crimp help
Weshoot2 - That's what I suspected. I've been away from reloading for a number of years but now getting back into it and while I'm certainly no expert, I didn't think I was totally out of the ballpark with this issue either. If you put marker or some other kind of marking material on the side of the case, it comes out of the die totally undisturbed, indicating to me that this thing must have been machined wrong. Thanks to all, especially you Weshoot for all the help. I have been lurking on this board for a while now but find an increasing need to seek advice from time to time. Thanks again, Tom
|
August 28, 2005, 09:48 AM | #9 |
Senior Member
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,324
|
yer welcome
But mostly I just make stuff up.........
148g WC / Bullseye or W231.
__________________
. "all my ammo is mostly retired factory ammo" |
August 28, 2005, 09:55 AM | #10 |
Member
Join Date: August 5, 2005
Posts: 46
|
Profile Crimp Picture
Weshoot2 - Was able to take a good closeup pic of the test casing. Hope it comes trough, not a computer genius either.
|
August 28, 2005, 10:00 AM | #11 |
Senior Member
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,324
|
excellent picture
Should be seeing some taper below that 'band'.
Bad die, ay?
__________________
. "all my ammo is mostly retired factory ammo" |
August 28, 2005, 06:07 PM | #12 |
Senior Member
Join Date: August 3, 1999
Location: Houston, Texas
Posts: 2,991
|
Looking at the picture, I agree. Bad die. Send it back.
The profile crimp (which Weshoot2 suggested to me a while back) is a great die and I basically don't load for revolver without it. Works "perfect". As always "Thanks to Weshoot2!"
__________________
10mm and 357sig, the best things to come along since the 38 super! |
August 29, 2005, 05:40 AM | #13 |
Senior Member
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,324
|
welcome
But I read about it, too, so I'm just passing on what I learned from another........
__________________
. "all my ammo is mostly retired factory ammo" |
Thread Tools | Search this Thread |
|
|