January 14, 1999, 10:28 PM | #26 |
Member
Join Date: December 31, 1998
Location: Downey, CA USA
Posts: 16
|
Rob,
Just to be a smartass, I'd like to refute your statement about the feather and bowling ball. Your teacher is right. If both are dropped in a vacuum, that is, under the same gravity. The reason the feather doesn't drop as fast is because it has a higher surface area to mass ratio, and consequently, higher drag. The proof for this is that acceleration due to gravity is constant for all objects (9.?? ft / sec.) I bet if you dropped me and a two ton block of led from a highrise, we'd both go splat at the same time. Not to give YOU any ideas of course! Mel |
January 15, 1999, 11:06 AM | #27 |
Senior Member
Join Date: October 22, 1998
Location: Diamond Bar, CA
Posts: 852
|
One thing we should all remember, as people who entrust our safety to firearms, is the Murphy factor. Always try to prepare for the worst case scenario, because it's better to have something and not need it, than need it and not have it.
Though I've never had a magazine set on me, I usually have three 8 round mags loaded for my 1911. I have 5 mags that I rotate out every 3 months, so there are always 2 mags that are not loaded. It takes me maybe 2 minutes each time. It may not be necessary, but it doesn't hurt me either. |
February 3, 1999, 10:18 AM | #28 |
Senior Member
Join Date: January 31, 1999
Location: SE Michigan - USA
Posts: 4,038
|
"Resting" magazine springs after being compressed for a very long period of time will not return them to the same contition they were when they were new. If the springs would not feed rounds correctly after a period of time, there is little that you can do to return those springs to "life". Pitch 'em.
As an aside: I was asked to check several firearms in an estate and found a flint lock rifle that was cocked. As far as anyone could remember the rifle had to have been cocked since sometime in the late '30's when the oldest son had been playing with it and forgot to lower the cock. The rifle was built in the early 1800's. I lowered the cock, thinking there would be no spring tension left and was suprised to find that the lock would still throw a good shower of sparks. (I tried the lock with the permission of the owners and only after making sure the rifle did not have a charge in the barrel.) |
February 4, 1999, 09:55 AM | #29 |
Senior Member
Join Date: October 11, 1998
Location: Natchez, MS, USA
Posts: 2,562
|
Or to rephrase the question:How much length and/or strength can a magazine spring lose and the magazine still function?
------------------ Better days to be, Ed |
February 5, 1999, 07:41 AM | #30 |
Senior Member
Join Date: January 6, 1999
Location: Somewhere in USA
Posts: 323
|
The other day when I went to the range had 2 magazine springs fail on me so....
Have had the 2 since 1990-1991 S&W 59,15 rounds, have had both loaded pretty much all the time, will call S&W and see if they send some "free" replacements If not will order some from Wolfe spring. ------------------ Justice for one,Justice for all. |
February 5, 1999, 07:27 PM | #31 |
Senior Member
Join Date: November 3, 1998
Location: Alamo, CA
Posts: 424
|
Flyer; I also have a M59. I have removed all the factory mag springs and replaced them with either +5% or +10% extra power springs from Wolff. They work very well.
|
February 10, 1999, 01:34 AM | #32 |
Senior Member
Join Date: February 10, 1999
Posts: 165
|
Here is some industry info...
My dad works for a wire company that supplies the wire to the spring companies that make gov. spec. clips. For springs to be accepted they have to have no "memory" and be able to constanly perform. So from what I've heard any Mil. spec. mags such as Beretta, AR-15, Sig 228 etc should have no problem with spring life. Happy shooting! go vols! |
February 14, 1999, 10:34 AM | #33 |
Member
Join Date: October 13, 1998
Location: Texas
Posts: 80
|
I have a system to avoid extended compression of magazine springs. I empty each magazine through the barrel of its assigned weapon each week. That way it gets to demonstrate the strength of its muscles and enjoy a few hours relaxation before being pressed(no pun intended) back into service. - Doc
|
February 14, 1999, 11:56 PM | #34 |
Senior Member
Join Date: February 14, 1999
Location: Eastern, PA, USA
Posts: 147
|
Only worry about mag spring set if you have a GLOCK. Wolff springmaker and everyone else will tell you that as long as you have a good quality spring you WILL NOT have spring set. Glock is the only gun that to my knowledge that is having problems with their mag springs ( out of the box )!!!!!!!!!!
|
February 23, 1999, 12:25 PM | #35 |
Senior Member
Join Date: February 15, 1999
Location: Leavenworth, KS USA
Posts: 606
|
Rich: I know of no problems w/mag springs taking a "set" and then failing to properly feed ammo. I do, as a matter of course, rotate the loaded mags I keep with my bedroom piece (SIG P220) and my downstairs piece (SIG P226) approximately every 90 days. Hey, it can't hurt and takes all of 2 minutes.
|
February 23, 1999, 05:14 PM | #36 |
Senior Member
Join Date: January 29, 1999
Location: Texas
Posts: 1,796
|
Until I began shooting Glocks, I never had a problem with a magazine spring. Now I do. Why Glocks have this problem, how extensive it is, and whether Glock is still supplying springs with a relatively short life I do not know.
At any rate, on the minus side, the magazine spring seems to be the weak point in the otherwise strong Glock system. On the plus side, the Glock service department has been very good about replacing problem springs for me at no charge. |
|
|