The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Semi-automatics

Reply
 
Thread Tools Search this Thread
Old May 5, 2021, 09:35 PM   #1
Sunflowers+Sixguns
Junior Member
 
Join Date: December 16, 2020
Posts: 5
Norinco SKS repair

I've recently purchased a Norinco SKS that has been very clearly assembled from a handful of different parts sources. Tapco stock, homebrew reduced capacity magazine assembly, mismatched wooden handguard, badly fitted replacement dust cover, and so on and so forth.

At this point it appears to be functional save for the magazine system. After removing the magazine assembly in a failed attempt to install a duckbill magazine, I discovered that the magazine it came with would no longer lock the bolt open when empty. My knowledge of the platform is limited, but this seems to be a result of poor home gun smithing on behalf of the previous owner.

At this point I'm at a loss for where to go next. Does anyone have suggestions on sorting out the magazine? Neither the cut down factory style not aftermarket duckbill will function. I can't even seat the duckbill mag.
Sunflowers+Sixguns is offline  
Old May 6, 2021, 12:19 AM   #2
tangolima
Senior Member
 
Join Date: September 28, 2013
Posts: 2,451
The original magazine is the best. The tip of the follower pushes up the hold open latch.

-TL

Sent from my SM-N960U using Tapatalk
tangolima is online now  
Old May 6, 2021, 05:57 AM   #3
Sunflowers+Sixguns
Junior Member
 
Join Date: December 16, 2020
Posts: 5
I was told that the original magazine (at least it's the same as the OEM style design) was cut down to 5 rounds by a previous owned. Not pinned or blocked, actually cut apart and shortened. It does not seat properly now, so I will be replacing it with something. Would my best bet likely be to find another factory magazine to swap it for?
Sunflowers+Sixguns is offline  
Old May 6, 2021, 06:10 AM   #4
MC 1911
Senior Member
 
Join Date: February 19, 2011
Location: Virginia
Posts: 240
Trash the Tapco & the duckbill. Put it back in a wood stock with a factory mag. Not sure how or why someone would reduce the capacity on the original mag.

A few pics would be nice to see what you're working with.
MC 1911 is offline  
Old May 6, 2021, 03:00 PM   #5
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 14,623
If you can find one, the metal 10-round mags are best. Problem is, a lot of people took them off and trashed them, so they may be hard to locate.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Scorch is offline  
Old May 6, 2021, 03:37 PM   #6
MC 1911
Senior Member
 
Join Date: February 19, 2011
Location: Virginia
Posts: 240
Stocks & original mags can be found on Ebay among other places.
MC 1911 is offline  
Old May 7, 2021, 06:19 PM   #7
dyl
Senior Member
 
Join Date: October 31, 2009
Location: Ohio
Posts: 1,307
Does it still have a hold open latch? There should be a little rectangular piece (if I remember correctly) that can manually be slid upwards to hold the bolt in the rearward position.

I noticed SKS parts were already getting a little sparse even before Coronavirus. If you can't find a wood stock, a jungle (fiberglass) stock should fit too. And if you really can't find any original stock, I think ProMag makes an SKS stock that doesn't look as bad as the Tapco. The only critique I remember about it is a longer length of pull.
dyl is offline  
Old May 9, 2021, 07:55 AM   #8
44caliberkid
Senior Member
 
Join Date: May 15, 2017
Location: Iowa
Posts: 620
SKS parts are also getting expensive. Chinese parts even more so. A factory 10 rounder was about $40 before Covid. Then I was offered an SKS to buy, that had lots of missing parts, but even with the parts it would have been a $300 - 350 gun, and I couldn't get it cheap enough to justify buying the parts and finishing it up.
44caliberkid is offline  
Old May 12, 2021, 10:44 AM   #9
Ricklin
Senior Member
 
Join Date: February 22, 2008
Location: SW Washington state
Posts: 1,704
I've used the promag stock years ago. Made that short little SKS much more usable for me, I'm tall and lanky, SKS just don't fit folks like me. The promag stock really helped.
Stripper clips and the original 10 rounder are the way to go. My buddy was a fan of the 30 rounders. I made him a gentlemen's wager of who could dump 30 rounds the fastest.
My SKS never jams using a 10 rounder, with 2 strippers ready to go, no contest, not even close 1 jam would have been enough, since his jammed twice I could have taken a short nap and still "won" he is a stubborn cuss.

IMHO the only way to improve an SKS is to improve the fit, they are what they are.
__________________
ricklin
Freedom is not free
Ricklin is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:51 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2020 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.07354 seconds with 10 queries