The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools Search this Thread
Old June 5, 2019, 08:21 AM   #1
ReloadKy
Senior Member
 
Join Date: February 23, 2018
Posts: 123
6.5 Creedmor reloading problems?

I do not have a 6.5 but my brother does. He started shooting Hornady precision hunter ammo with the 143 gr ELDX when he bought the rifle. we decided to reload some of the ELDX bullets ourselves to see how good we do. We made up 5 rounds. All cases were neck sized, checked for trim length (all were at 1.912), chamfer / deburred, primed and loaded. When he went to shoot 2 out of the 5 rounds would not chamber. They were loaded to 2.800 OAL. Becuase the OAL was close to max I decided the rifle (Browning X bolt) must have a short throat so I decided to push them down to 2.780 and they still would not chamber. I pulled the bullets and rechecked the trim length for the two cases that would not fire and they are well below max trim length. What is my problem here and what am I missing? I have never had this problem in any other rifle I have reloaded for.

Is there a way I can safely remove primers and start the process over from the beginning? The way I figure it I had to have made a mistake in the resizing process. Any help is much appreciated I am confused.
ReloadKy is offline  
Old June 5, 2019, 09:07 AM   #2
Don Fischer
Senior Member
 
Join Date: March 2, 2017
Posts: 1,407
When you pulled out the one's that wouldn't go, were there marks around the ogive? If not then seating depth is not the problem. My first guess would be your getting into the crimp function on the die to much and blowing out the shoulder just a bit.
Don Fischer is offline  
Old June 5, 2019, 09:16 AM   #3
Bart B.
Senior Member
 
Join Date: February 15, 2009
Posts: 6,650
Does a once fired new case rechamber easily?

If yes, then the reloading process is flawed. What type of die was used to neck size, full length or neck only?

Primers can be removed safely with a larger die moving the ram very slow. I have used a seating die with the decapping stem screwed in.

Last edited by Bart B.; June 5, 2019 at 09:26 AM.
Bart B. is offline  
Old June 5, 2019, 10:03 AM   #4
Jimro
Senior Member
 
Join Date: October 18, 2006
Posts: 7,097
It sounds like you might have pushed out the case shoulder a little bit in the seating process. A run through a body die would fix that right up.
__________________
Machine guns are awesome until you have to carry one.
Jimro is offline  
Old June 5, 2019, 11:54 AM   #5
ReloadKy
Senior Member
 
Join Date: February 23, 2018
Posts: 123
Jimro got it. I finally got the "bright" idea to measure the case shoulder. It was not pushed out enough to really notice with the naked eye but it definitely is. Thanks for the suggestions. This is a great place to get suggestions on fixing issues I encounter.
ReloadKy is offline  
Old June 5, 2019, 12:58 PM   #6
T. O'Heir
Senior Member
 
Join Date: February 13, 2002
Location: Canada
Posts: 11,137
"...made up 5 rounds..."Isn't enough. Even though the bullets are the same, you still must work up the load.
How did you neck size 'em?
The shoulder issue is, like Jimro says, the seater die being down too far. Have a few .30-06 like that.
"...safely remove primers..." Just gently and slowly run 'em though the decapper.
__________________
Spelling and grammar count!
T. O'Heir is offline  
Old June 5, 2019, 07:15 PM   #7
sako2
Senior Member
 
Join Date: April 12, 2009
Posts: 340
Remove the decapping pin and resize them.
sako2 is offline  
Old June 5, 2019, 08:03 PM   #8
ReloadKy
Senior Member
 
Join Date: February 23, 2018
Posts: 123
sako I did exactly that earlier today. They chambered just fine. Problem solved.
ReloadKy is offline  
Old June 6, 2019, 06:20 AM   #9
m&p45acp10+1
Senior Member
 
Join Date: May 3, 2009
Location: Central Texas
Posts: 3,870
If your seating die crimps I would advise to back it off one and half turns. Then Adjust the seating stem to length. If it happens again run a fingernail from the base to the shoulder. If it catches on the shoulder you either have the seating die set too low and it is over crimping. Or your case mouth is too undersized for the bullet, and it pushes the shoulder down when the case mouth is forced down from seating an over sized bullet.
__________________
No matter how many times you do it and nothing happens it only takes something going wrong one time to kill you.
m&p45acp10+1 is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:52 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05539 seconds with 8 queries