|
February 23, 2023, 11:28 AM
|
#1 |
|
Senior Member
Join Date: October 30, 2021
Posts: 245
|
repairing scratch
I managed to scratch the frame on one of my new 1911's. Is there
a way to cover them? |
|
|
February 23, 2023, 03:38 PM
|
#2 |
|
Member
Join Date: October 23, 2021
Location: Deep South
Posts: 53
|
What metal and finish is it?
|
|
|
|
February 23, 2023, 06:10 PM
|
#3 |
|
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,680
|
Not without extensive refinishing. The finish reflects the finish and even if you could perfectly blue that scratch, when held to the light the scratch will appear.
Easiest way to hide it is paint it.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
|
|
|
February 23, 2023, 08:59 PM
|
#4 |
|
Senior Member
Join Date: October 30, 2021
Posts: 245
|
It is steel, don't plan to sell it, just cover over the scratch so I don't see it
( never hold it up to the light anyway) |
|
|
|
February 23, 2023, 09:49 PM
|
#5 |
|
Senior Member
Join Date: April 7, 2006
Posts: 10,908
|
Blued steel? Plated steel? Stainless steel?
|
|
|
|
February 23, 2023, 10:50 PM
|
#6 |
|
Senior Member
Join Date: November 13, 2022
Posts: 129
|
If it's a light scratch I buff it with oiled 0000 steel wool and a oily pure cotton rag or synthetic micro fiber rag.
|
|
|
February 24, 2023, 09:38 AM
|
#7 |
|
Senior Member
Join Date: October 30, 2021
Posts: 245
|
Blued steel
|
|
|
|
February 24, 2023, 10:41 AM
|
#8 |
|
Staff
Join Date: February 12, 2001
Location: DFW Area
Posts: 24,580
|
It won't be perfect, but Oxpho Blue will work for a touchup. I've had good luck with it--sometimes, depending on the shade of the blueing and the size of the scratch it can make it virtually invisible.
__________________
Do you know about the TEXAS State Rifle Association?
|
|
|
|
February 24, 2023, 12:47 PM
|
#9 |
|
Senior Member
Join Date: February 16, 2006
Location: IOWA
Posts: 8,719
|
Take care with cold-bluing (MHO)
On Blued steel, you have to take care when applying any cold-blue as the steel adjacent to the scratch "may" also take the bluing and you wind up with a blotchy appearance and you will lose the effect you want. Practice on a hidden area like under the grip. For now, I think I would just cover the the scratch with a fine black sharpy. In time, the "bright" will fade .......
 Good luck and; Be Safe !!!
__________________
'Fundamental truths' are easy to recognize because they are verified daily through simple observation and thus, require no testing. 
|
|
|
|
February 24, 2023, 06:08 PM
|
#10 |
|
Senior Member
Join Date: April 7, 2006
Posts: 10,908
|
If you can pull the liquid cold blue into and through the scratch with a toothpick or similar, it might work OK.
Smearing cold blue OVER the scratch will likely discolor the bluing. |
|
|
|
February 24, 2023, 06:44 PM
|
#11 |
|
Staff
Join Date: February 12, 2001
Location: DFW Area
Posts: 24,580
|
Yes. That's good advice. It should be done as a touchup, restricting it, as much as possible, to the scratch itself, not simply smeared over a general area.
__________________
Do you know about the TEXAS State Rifle Association?
|
|
|
|
February 25, 2023, 03:46 PM
|
#12 |
|
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,680
|
Certainly you can apply touch up (after degreasing) into the scratch, but under certain light that scratch will still appear. So you're not "repairing the scratch" but trying to conceal it. The only way to remove it is to repolish the entire surface and then refinish (blue) it.
Scratches and dings are a part of use/ownership. I accept them as normal wear and tear.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
|
|
|
February 25, 2023, 03:58 PM
|
#13 | |
|
Senior Member
Join Date: February 16, 2006
Location: IOWA
Posts: 8,719
|
Reality Check !!!???
Quote:
Be Safe !!!
__________________
'Fundamental truths' are easy to recognize because they are verified daily through simple observation and thus, require no testing.
|
|
|
|
 |
| Thread Tools | Search this Thread |
|
|
