|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
June 2, 2009, 05:38 PM | #1 |
Member
Join Date: June 2, 2009
Location: Central TX
Posts: 92
|
Your Ideal Die Set - Pistol
I've been reloading for about 15 years, and have tried a lot of different makers dies. After a lot of trial and error, I've come up with a "set" that works best for me. I'm mainly reloading 45 ACP and 45LC with a mix of plated, cast, and Jacket bullets. I'm curious if anyone else has come up with a preferred Hybrid set of dies for a caliber - I reload on a first gen Hornady LnL AP press.
Decapping and Sizing - RCBS because of the cheap replaceable de-capping pins Expanding - Lyman M Die. - I really like the profile it leaves on the case mouth that makes seating cast or plated bullets supper easy. Also very easy to adjust for jacketed bullets when you don't want to overwork the case mouths. Seating - Hornady because of the floating seater stem that practically guarantees a straight bullet. I don't crimp with this die though leaving it cranked out enough so it only seats. Crimp - Lee Factory Crimp Die works great for either my roll crimping, or Taper Crimping needs depending on Caliber. I especially like the post-load resizing step for 100% reliable functioning with 45ACP during Bullseye matches. Does anyone else mix and match dies? |
June 2, 2009, 05:43 PM | #2 |
Member
Join Date: May 25, 2009
Location: New Castle, PA
Posts: 95
|
I don't mix up sets but have tried several brands of dies and for the money you can beat Lee carbide 4 die kits. My dad gave me his 38 spl. dies and they work great. I think they're older than I am.
|
June 2, 2009, 05:52 PM | #3 |
Senior Member
Join Date: May 30, 2009
Posts: 136
|
I've replaced my 25+ yr RCBS steel sizers with Lee carbide, when I didn't purchase RCBS carbide dies in the sets. I only use the Lee Factory Crimp Die on jacketed bullets as I found out that the FCD resizes my cast bullets. As a test I pulled the cast bullets after using the FCD and measured the bullet.
|
June 2, 2009, 06:17 PM | #4 | |
Senior Member
Join Date: July 28, 2007
Location: Ohio
Posts: 11,756
|
Quote:
__________________
Attention Brass rats and other reloaders: I really need .327 Federal Magnum brass, no lot size too small. Tell me what caliber you need and I'll see what I have to swap. PM me and we'll discuss. |
|
June 2, 2009, 06:19 PM | #5 |
Senior Member
Join Date: November 8, 2007
Posts: 2,001
|
For pistol cases, my "mixed" set is similar to Pocketfisherman's, but a little more "customized." In order of use:
1. The body of a Lee factory crimp die with a home-made insert that holds an RCBS decapping rod. The carbide ring in the FCD resizes the entire case to withing SAAMI diameter specs and my addition decaps. 2. The RCBS carbide sizer, turned in only far enough to size the case down below the area where the bullet is seated. 3. The Lyman "M" die or equivalent from Redding to expand the case and flare it. I have some home-made expander plugs that have the M die "step" expander shape, but are shortened so that they only expand the case as far as the bullet is seated. This leaves a small length of case at a diameter set by the RCBS carbide ring to substantially less than the bullet, which helps resist bullet set-back. 4. The Hornady bullet seating die with the sliding sleeve. 5. A separate crimp die, either a Lee FCD using a die body for a larger diameter cartridge so that the carbide ring does not "post-size" or a Redding die. SL1 |
June 2, 2009, 07:00 PM | #6 |
Senior Member
Join Date: April 15, 2009
Location: Wyoming
Posts: 1,717
|
It's good to hear other's experiences. So far I have only used Lee dies because I started reloading earlier this year and those were the only dies available for my cartridges period, so I didn't have any choice.
But it does raise a question for me to ask the experienced hands. I wonder if I'm doing something wrong with the expander/flaring die. It doesn't seem to do anything at all. I have tried adjusting it every which way, but in the case of loading cast bullets for my 38 brass, I can't get the necks large enough to even get the bullets started into the case. Basically, they just rest on top of the cases and I have to very gingerly set the case/bullet onto the shell holder and hope that it doesn't fall off on its way into the seating die. It's kind of the same problem with the 45 Colt, but not quite as bad. Yes, it does shave off a tiny sliver of lead by the time it is seated. The jacketed bullets I use for 357 also don't really go inside the cases, but at least the jacketed bullets do slide into the cases fairly easily with no shaving. I just thought the expander die was supposed to be able to flare the case mouths a lot if you so desire. |
June 2, 2009, 09:14 PM | #7 |
Senior Member
Join Date: March 22, 2006
Posts: 111
|
For 9mm in my Hornady LNL progressive:
1 hornady sizer and decapper 2 Hornady powder through expander using a .357 insert 3 Lee 357 seater 4 RCBS .380 ACP taper crimp- nice uniform crimp and the die doesnt touch the shell plate and kick wire. This combo works pretty good for me |
June 2, 2009, 09:32 PM | #8 |
Senior Member
Join Date: April 16, 2008
Location: Missouri
Posts: 1,891
|
I'm a big fan of the Lee Deluxe 4 die sets for pistols. Granted, I'm new at reloading, but I have finished about 1500rds of 9mm. The Lee Factory crimp die is great. I've also managed to break a decapping pin (long story, my fault) and Lee's customer service was excellent. One phone call and within a week I had a new one free of charge.
__________________
Hopp Custom Leather <------ click for HOLSTER awesomeness!! -There is no theory of evolution... Just a list of creatures Chuck Norris has allowed to live. |
June 2, 2009, 10:26 PM | #9 |
Junior member
Join Date: January 23, 2008
Location: MI
Posts: 1,398
|
Handgun: Redding Pro Series only. Exception: 357 Mag 215gr LSWC gets the FCD due to the bulge during seating the long bullet.
Rifle: Redding only. Have .223 set up in a Lee Classic Turret for case prep as follows: Universal decapper RCBS lube die Dillon carbide FL size die Redding trim die I modified a small primer arm for the LCT with a pocket swaging point so when I decap it, I perform the same function as I would seating a primer on the way down but instead it swages the crimp from the primer pocket. Decap, down to swage the pocket, then lube, then size, then trim if needed. Done. |
June 3, 2009, 08:10 AM | #10 |
Senior Member
Join Date: December 1, 2002
Posts: 2,832
|
"Decapping and Sizing - RCBS"
"Expanding - Lyman M Die." "Seating - Hornady" "Crimp - Lee Factory Crimp Die" Excellant choices. I do mix sets because no maker has a lock on all the good ideas! Actually, I don't much care who made the sizer/decapper die but the RCBS is as good as any. Redding has an exact copy of Lyman's excellant M die but, so far as I know, they don't sell it individually as Lyman does. |
June 3, 2009, 08:54 AM | #11 |
Senior Member
Join Date: January 20, 2009
Location: Overlooking the Baker River Valley
Posts: 1,723
|
This is a little different way of mixing: I use a .40 S&W carbide die to size my .357 SIG brass first, then continue with the .357 SIG dies. That way, I don't need to lube the .357 SIG cases, which carbide dies aren't available for because they have a [slight] bottleneck.
|
June 3, 2009, 02:27 PM | #12 |
Member
Join Date: June 2, 2009
Location: Central TX
Posts: 92
|
I'll remember that one. A sig 357 caliber conversion kit is in my future for my Sig P250.
|
June 6, 2009, 06:45 AM | #13 |
Senior Member
Join Date: October 17, 2004
Location: Rural N.H.
Posts: 1,586
|
WOW Pocketfisherman and SL1, I thought I was alone in mixing my dies. I have to agree though expensive I have had the best results doing this also. I have had some LEE sizing dies that oversized sized the case and had trouble with bullet setback ( I always check tension before going to the range ) but when switching to the RCBS the problem goes away. I have checked the size and the LEE is a couple thousenths over, and in the world of reloading this can be BIG! Due to that I had to crimp the heck out of my reloads to get the bullets to stay put. My die layout is exactly as wncchesters and pocketfisherman for my 9mm and the same as SL1 for my 40S&W.
__________________
The real danger to America is not abroad but within.. Having an open mind is a good thing, but not so open that your brains fall out! Save America, abort liberalism. |
June 6, 2009, 05:47 PM | #14 |
Junior member
Join Date: December 10, 2001
Location: Burbs of Minneapolis
Posts: 676
|
Redding Pro Series Titanium Carbide all the way! If was loading a bunch of different bullets I would the Pro Series Competition Titanium Carbide Die Set.
Great quality! |
June 6, 2009, 07:16 PM | #15 |
Member
Join Date: April 23, 2009
Location: Tampa, Florida
Posts: 76
|
I vote lee 4 die carbide sets as well
__________________
Never compromise, never surrender. |
|
|