The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools Search this Thread
Old December 29, 2010, 02:28 AM   #1
daleo8803
Member
 
Join Date: August 3, 2009
Posts: 78
32 H & R mag die question

i have a 327 mag revolver that i want to start reloading for. i used lee stuff normaly but they dont seem to make dies for the 327 mag yet. i can get a set of 32 h&r dies for cheap but i need to know if they will work for the 327. thanks

dale
daleo8803 is offline  
Old December 29, 2010, 03:26 PM   #2
barryhud
Member
 
Join Date: September 7, 2007
Location: Southeast Oklahoma
Posts: 85
I use the same Lee dies to load 32 long, 32mag and 327.
barryhud is offline  
Old December 29, 2010, 06:02 PM   #3
willr
Senior Member
 
Join Date: July 23, 2006
Posts: 353
I have been using Lee 32 H&R Mag dies for over a year now -- no problems. Even use the 32 mag factory crimp die. Have talked with a gunsmith who uses the same dies for his 327 mag.

willr
willr is offline  
Old January 11, 2011, 11:44 PM   #4
triumph666
Senior Member
 
Join Date: January 11, 2011
Posts: 374
32 hr mag die

these guys are correct...32 H&R dies are used to reload 32 sw long ,32 hr mag and 327 fed mag
triumph666 is offline  
Old January 12, 2011, 12:27 AM   #5
Crankylove
Senior Member
 
Join Date: July 8, 2008
Location: Tooele, Ut
Posts: 1,563
Only difference will be that with the longer cases, the die won't size as far down the case walls, which really shouldn't be an issue anyway. My brother uses his dies for .32 S&W, .32 S&W Long, .32 H&R, and .327 with no issues that I am aware of.
__________________
The answer to 1984 is 1776
Crankylove is offline  
Old February 21, 2011, 02:29 PM   #6
bhasi
Junior Member
 
Join Date: December 27, 2010
Posts: 1
can anyone tell me which is universal die for 32 cal,

Does buying HR mag dies are enough for all 32 Calibers? 32Long/32 HR/327 Fed mag? or is it 32 Long die set.
bhasi is offline  
Old February 21, 2011, 03:24 PM   #7
FrankenMauser
Senior Member
 
Join Date: August 25, 2008
Location: Potatoes and Hops
Posts: 11,936
Most .32 S&W Long die sets will work for .32 H&R and .327 Federal, but only the RCBS and Hornady die sets have been recently 'clearanced' to work specifically with the .327 Federal.

That being said....
I have had a lot of issues with Magtech and Starline .32 S&W Long brass in the RCBS .32L/H&R/.327 sizing die. It doesn't get sized small enough to have the proper neck tension for most bullets (even without being belled/expanded). It may not be an issue with the die, but an issue with elasticity of the brass.

So, I size my .32 S&W Long brass in a .32 S&W / .32 Auto die, and then expand the mouth with a Lyman 'M' die. (.32 H&R and .327 Federal are just fine in the RCBS dies.)

I shoot .32 Auto, .32 S&W, .32 S&W L, .32 H&R, and .327 Federal in my Blackhawk. To take care of all of them, I use different combinations of the following:
RCBS Carbide 3 die set, .32 S&W L/.32 H&R/.327
Lee .32 S&W 3 die set, (a combination of .32 S&W, .32 Auto, and .32 S&W L dies)
Lyman .32 S&W Long 'M' die
Redding .32 H&R profile crimp die
__________________
Don't even try it. It's even worse than the internet would lead you to believe.
FrankenMauser is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:05 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06834 seconds with 10 queries