May 12, 2010, 11:02 PM | #1 |
Junior Member
Join Date: April 16, 2009
Location: capital of Kalifornia
Posts: 4
|
PMC Brass?
Hello everyone, I just picked up a new riffle.its a CZ550 in 6.5x55 swede. I can find PMC brass on line for about .28 if I buy 500. Has anyone Used the Rifle brass? Or any other PMC rifle brass?
|
May 12, 2010, 11:29 PM | #2 |
Member
Join Date: January 12, 2010
Location: "A Facist Subject" California
Posts: 64
|
PMC Brass
I've used 22-250 PMC Brass it was approximately .001" thicker at the neck than my Winchester Brass, maybe it was that particular lot (.0145"~.015"). In my case that was not a bad thing, since I had a liberal neck dimension from the factory.
O'B |
May 12, 2010, 11:30 PM | #3 |
Junior member
Join Date: May 12, 2010
Posts: 1
|
pmc brass
not a fan at all cheapest brass on the market. not good after about 4 to 5 med load and 2 hot loads
|
May 13, 2010, 12:18 AM | #4 |
Senior Member
Join Date: April 20, 2009
Location: Cape Town - South Africa
Posts: 627
|
Hi,
I have about 50 cases that a kind soul left at the range Normally I use Federal cases, but I tested a couple of my "pet" loads with the PMC and the groups were just as good (3/4 MOA was the best, and IMO it is acceptable) If this is all you can find and they are reasonably priced go for them. BTW, I use a Remington 700 in 30-06. Brgds, Danny Last edited by Dannyl; May 13, 2010 at 05:13 AM. |
May 13, 2010, 12:20 AM | #5 |
Senior Member
Join Date: March 12, 2010
Posts: 1,860
|
i have reloaded some PMC .223 brass without any problems.
|
May 13, 2010, 09:20 AM | #6 |
Senior Member
Join Date: May 15, 2008
Location: Louisville, KY
Posts: 701
|
Dad had problems getting 243 PMC brass to size. But he is using a hand loader not a press. I have tons of PMC in 45 ACP and it loads great. I would small lot of it like 20 or 50 and try it.
|
May 14, 2010, 03:06 PM | #7 |
Member
Join Date: February 7, 2010
Posts: 36
|
Twopatch
Ive got about 6,000 PMC cases in .308 Winchester it's mil spec brass so it has less volume then commerical brass. So i keep the Max load load about 2 grians less, but it has never given me any problums but it has produced some real tight groups for me |
May 14, 2010, 03:18 PM | #8 |
Senior Member
Join Date: February 12, 2010
Posts: 168
|
I have reloaded 223 PMC many times over and it's still hanging in there. It seems to be as durable as any other I've tried. I reload just to plink, so brass longevity is most important to me. I can't speak to group size, consistency, etc. Not really my cup O' tea.
|
May 15, 2010, 10:59 PM | #9 |
Junior Member
Join Date: April 16, 2009
Location: capital of Kalifornia
Posts: 4
|
cool,I might just,pull the trigger,"excuse the pun". The Europen stuff is 1-.75 per case. the Win-Rem is about .50 . I guess , We will see how this Korean stuff turns out. .28 cents is hard to resist!
|
|
|