The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools Search this Thread
Old November 26, 2012, 04:45 PM   #1
jason41987
Senior Member
 
Join Date: April 19, 2012
Posts: 479
uberti or piettas 1860 army?

im looking to purchase an 1860 army, and was wondering how pietta and ubertis are now, i know recently both companies have put a new effort into making higher quality, more historically accurate pieces, but i hear ubertis match up nearly perfectly with even original colt parts and piettas do not... for example, the 1851 navy pietta does not match the grip shape of original colts, ubertis 1851 navy does

so..how close to historically accurate are the pietta 1860s?... close enough that an original 1860 grip would fit over it or are these out of spec as well?..

it looks like the uberti would be about $100 more than the pietta... the parts of the pietta that are out of spec, if they still are, i dont have a recent one near me, is it possible to make these in spec?... what i mean is with some fine tuning, can i get everything to the proper shape it needs to be, and even drill out and re-thread some of the holes to fit, for example, an SAA grip frame... or do these holes just not match up?
jason41987 is offline  
Old November 26, 2012, 05:48 PM   #2
Doc Hoy
Senior Member
 
Join Date: October 24, 2008
Location: Naples, Fl
Posts: 5,440
I am going out on a limb....

....But I think it depends on what you will be doing with it.

I think that Uberti and Pietta are largely equivalent in quality as long as you stick with a recent issue as you have said. I also think that both are equally wrong as regards historical accuracy

Check me on this you historians but IIRC, the Belgian Centaure is a more faithful reproduction of the original dimensions of the pistol.

I think you may find that Uberti markings are in more out-of-the-way places on the pistol in comparison with Pietta.

So If you are going to do re-enacting, you might want to check with the regiment you are joining to see what their rules are. The N-SSA may also have a say in the way that replica revolvers are judged.
__________________
Seek truth. Relax. Take a breath.
Doc Hoy is offline  
Old November 26, 2012, 06:17 PM   #3
towboat-er
Senior Member
 
Join Date: December 2, 2011
Posts: 146
Cabelas has a great price on their 1860's now. Piettas are great guns for the money.
http://www.cabelas.com/browse.cmd?ca...3Bcat104701680
towboat-er is offline  
Old November 26, 2012, 07:08 PM   #4
Beagle333
Senior Member
 
Join Date: January 7, 2012
Location: Auburn, AL.
Posts: 2,332
I have only one Uberti, a Walker, and I got no problems with it. But I got a half dzn Pietta 1860's and '51s and I like them all. (Maybe I got lucky, but I haven't had a lemon in the pack of em.)

I did get a Pietta London Navy that had a crooked mounted triggerguard, but somebody had either damaged it in shipping or it was a return, but Cabelas promptly sent me a new one, no questions. (Back in Feb of this year)
I don't think it was Pietta's fault that it was damaged.
Beagle333 is offline  
Old November 26, 2012, 07:30 PM   #5
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,177
Quote:
so..how close to historically accurate are the pietta 1860s?... close enough that an original 1860 grip would fit over it or are these out of spec as well?..
If you're talking about just the wood it will fit neither Pietta or Uberti without fitting. Both of them do the final fitting of the grips with the grip frame installed, so no two sets of grips will perfectly interchange. As for the grip frame fitting as is I have my doubts on that too bit I have no experience with it.
Hawg is offline  
Old November 26, 2012, 07:40 PM   #6
jason41987
Senior Member
 
Join Date: April 19, 2012
Posts: 479
i seen a colt SAA grip matched up to an uberti 1851, and it fit almost perfectly, but when matched to a pietta there were a lot of differences in the profile of the grip frame... im not sure if pietta has corrected this yet or not, or if it even exists on other models which is why i was wondering...

a pietta is about $200 at cabelas, and an uberti is about $280, and id be willing to pay the extra $80 of the uberti was closer to original, holes drilled in the right places, proper profile, etc... im also willing to do a bit of work to make them more authentic if necessary, such as fine tuning the grip profile and grips themselves, deburr parts, trigger work, etc
jason41987 is offline  
Old November 26, 2012, 09:00 PM   #7
Beagle333
Senior Member
 
Join Date: January 7, 2012
Location: Auburn, AL.
Posts: 2,332
Quote:
no two sets of grips will perfectly interchange
You got that right!

I've had some that'll swap out close enough to use, and some that aren't even close enough to screw down. . . and they were all Piettas. It's an individual thing. . . you'll get lucky if two will swap without any gaps/overlaps - grips and frames both.
Beagle333 is offline  
Old November 26, 2012, 09:14 PM   #8
jason41987
Senior Member
 
Join Date: April 19, 2012
Posts: 479
im more concerned with the backstrap having the proper shape than the individual grip panels themselves... does a pietta 1860 army have the proper grip frame shape?
jason41987 is offline  
Old November 26, 2012, 11:10 PM   #9
MJN77
Senior Member
 
Join Date: April 27, 2009
Location: on a hill in West Virginia
Posts: 789
Both are good guns, but the Uberti is closer in shape and size to the original Colts.
MJN77 is offline  
Old November 26, 2012, 11:30 PM   #10
Hellgate
Senior Member
 
Join Date: November 18, 2010
Location: Orygun
Posts: 868
One area of difference between the originals and the repros is the area under the rammer. The Piettas have the LEAST room under the rammer & cylinder pin to accomodate a conical ball. The Ubertis have more room. I like to shoot conicals but I could not get one into the chambers of a Pietta '60 Army but I could under my ASM Hartford model 1860 Army with just a little jiggling. My recollection of many years ago when I had a Cimarron 1860 Army was that there was even more room. I believe the Cimarron was a Uberti. Ihave not problem whatsoever getting a conical into any Remington.

As for grip fit, pretty much you have to stay within the same manufacturer to get grip frames to fit the screw holes. i.e. Pietta to Pietta and Uberti to Uberti, ASM to ASM. I have swapped grips from the Navy size to the Army and vise versa but always within the same manufacturer. I hate the belled/flared Pietta navy grips and have put Pietta Army grips on a J H Dance and a '51 Navy.
__________________
With over 15 perCUSSIN' revolvers, I've been called the Imelda Marcos of cap & ball.
SASS#3302 (Life), SASS Regulator, NRA (Life), Dirty Gamey Bastards #129
Wolverton Mtn. Peacekeepers (WA), former Orygun Cowboy (Ranger, Posse from Hell)
Hellgate is offline  
Old November 27, 2012, 12:02 AM   #11
jason41987
Senior Member
 
Join Date: April 19, 2012
Posts: 479
ive been thinking of doing my own richards or mason style conversion... wanted to put an SAA birds head grip on it.. such a conversion does include a cartridge conversion as well, so, area under the rammer isnt all that important...

im mostly concerned with being able to change out the grip frame... if the screws were close enough, but not of the proper thread or size, they could be bored out and re-tapped.. but if they dont even line up at all i guess theres not much you can do about it
jason41987 is offline  
Old November 27, 2012, 06:51 AM   #12
MJN77
Senior Member
 
Join Date: April 27, 2009
Location: on a hill in West Virginia
Posts: 789
You can switch grip frames of different revolvers of the same brand (uberti to uberti/pietta to pietta). I have done it many times. You might have to do a little bit of fitting, but nothing major.
MJN77 is offline  
Old December 1, 2012, 07:05 AM   #13
enyaw
Senior Member
 
Join Date: November 28, 2008
Posts: 134
I think the Pietta Army is close enough in grip shape to original. The Navy is too flared and is a sore spot on the gun. The Pietta London Navy has a better shaped grip compared to the original. Steel backstrap though. Same as used on the 1861 Navy I suppose.
Too bad Pietta doesn't get that brass Navy grip shape more in line. Nice pistols with a funky grip.
enyaw is offline  
Old December 1, 2012, 09:51 AM   #14
brazosdave
Senior Member
 
Join Date: September 7, 2012
Location: Crockett, Texas
Posts: 363
I don't know, but I like my Pietta 1860
__________________
"I'm your huckleberry, it's just my game"
brazosdave is offline  
Old December 1, 2012, 10:40 PM   #15
jason41987
Senior Member
 
Join Date: April 19, 2012
Posts: 479
i actually made my choice.. i ordered a pietta 1860 army london model.. which has the steel 1851 grip frame off their 1851 london... so my 1860 army is going to have an 1851 style grip.... but piettas steel grip frames are the correct shape, unlike their brass ones
jason41987 is offline  
Old December 1, 2012, 11:51 PM   #16
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,177
That's another never was. The first 60's did have a navy grip frame but it was brass. The army specified the longer grip but the 1860 was never made in London.
Hawg is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:41 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.07295 seconds with 10 queries