The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools Search this Thread
Old April 16, 2012, 01:05 AM   #1
Davey
Senior Member
 
Join Date: August 2, 2010
Location: Not far enough from Chicago
Posts: 394
Compare my crimp before and after please,

Here are two pics of a crimped and uncrimped 45 ACP round

Round on the left is crimped, the one on the right is right after seating with no crimp.

Does it look like I have enough crimp applied?

Apparently I'm limited to the size of the images. The originals are much bigger. I'll post the originals if needed.

Thanks
Attached Images
File Type: jpg ImageUploadedByTapatalk1334556247.743616.jpg (40.8 KB, 137 views)
File Type: jpg ImageUploadedByTapatalk1334556263.099123.jpg (40.8 KB, 122 views)
Davey is offline  
Old April 16, 2012, 01:16 AM   #2
mrawesome22
Senior Member
 
Join Date: November 9, 2005
Location: Ohio, Appalachia's foothills.
Posts: 3,779
If they function is the only thing that matters.

Neck tension is all that is needed.

This cartridge just needs the flare removed to ensure smooth cycling.

Sent from my HTC Wildfire S A510e using Tapatalk 2
mrawesome22 is offline  
Old April 16, 2012, 01:20 AM   #3
Ethan.G
Senior Member
 
Join Date: March 13, 2012
Posts: 127
my test is if i can pull the bullet out by hand, then its not enough, other then that you should be solid, looks square to me be safe and have fun shooting them
Ethan.G is offline  
Old April 16, 2012, 01:37 AM   #4
chris in va
Senior Member
 
Join Date: December 26, 2004
Location: Louisville KY
Posts: 13,805
45's don't need a crimp unless you get feeding issues.
chris in va is offline  
Old April 16, 2012, 03:40 AM   #5
Powderman
Senior Member
 
Join Date: September 7, 2001
Location: Washington State
Posts: 2,166
The best way to tell for sure is to measure at the case mouth with calipers. The crimp specification for the cartridge calls for a case mouth diameter of .465 to .470. I crimp to .470, with a taper crimp die. No problems yet!
__________________
Hiding in plain sight...
Powderman is offline  
Old April 16, 2012, 11:38 AM   #6
mikld
Senior Member
 
Join Date: February 7, 2009
Location: Southern Oregon!
Posts: 2,891
The term "crimping" should not be used when talking about 45 ACP reloading; it just causes confusion for new reloaders. A taper crimp die is used to straighten out the flare applied to the case mouth to facilitate bullet seating, and neck tension should keep the bullet in place. "Case mouth reshaping die" is a better term "Reshape" the case mouth (crimp) enough to straighten out the flare to enable free chambering, but not too much that the case won't headspace on the case mouth. Hey, jes an old guy's opinion, but it works for me...

P.S.; a lot of guys measure the "crimped" case mouth and suggest .470" as a targer measurement.
__________________
My Anchor is holding fast!
I've learned how to stand on my own two knees...
mikld is offline  
Old April 16, 2012, 12:07 PM   #7
Lead Express
Senior Member
 
Join Date: January 21, 2012
Location: Sacramento
Posts: 125
As stated above, the term "crimp" for auto pistol cartridges is misleading. You should only be removing the flare from belling the case, just enough to seat a new bullet. Run your finger over the lip of the case, and if you see or feel the case mouth is still flared outwards, "crimp" a little more.
__________________
”An unarmed man can only flee from evil, and evil is not overcome by fleeing from it.”
~Col. Jeff Cooper
Lead Express is offline  
Old April 16, 2012, 12:13 PM   #8
Mal H
Staff
 
Join Date: March 20, 1999
Location: Somewhere in the woods of Northern Virginia
Posts: 16,939
An admin note - that image size is just right, no need for anything larger.

To me, both of your rounds look fine. And that makes me wonder if you're belling your cases at all before seating the bullet. If so, the crimp you have on the "non-crimped" round is just about right.
Mal H is offline  
Old April 16, 2012, 12:58 PM   #9
moxie
Senior Member
 
Join Date: October 17, 2006
Location: TX
Posts: 513
.470" is the correct crimp.
__________________
If you want to shoot...shoot...don't talk! Tuco

USAF Munitions 1969-1992
RVN 1972-1973
moxie is offline  
Old April 16, 2012, 10:16 PM   #10
Davey
Senior Member
 
Join Date: August 2, 2010
Location: Not far enough from Chicago
Posts: 394
I can hand fit a bullet into an expanded mouth with no problem. The measurement of the case at the very edge where it meets the bullet ranges from .4695 to .470 on my semi cheapo digital caliper before running through the crimp die. There doesn't seem to be any change in diameter at all after running them through my Lee factory crimp die.
Davey is offline  
Old April 16, 2012, 10:45 PM   #11
Powderman
Senior Member
 
Join Date: September 7, 2001
Location: Washington State
Posts: 2,166
The measurement does seem to be on the tight side, if you're measuring before you seat the bullet. The measurement is correct, though, if measuring after the bullet is seated.
__________________
Hiding in plain sight...
Powderman is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:25 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.07377 seconds with 11 queries