|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
March 6, 2013, 09:53 PM | #1 |
Senior Member
Join Date: January 28, 2013
Location: Land of 10,000 taxes
Posts: 211
|
To size or not to size ???
I'm loading .38 Special, casting Lee 158 grain .358" SWC tumble lube, 3.0 grs. Clays, CCI small pistol primers
The bullets are comming out at 155 - 158 grains and measureing .358" to .360". After casting 0ver 400 bullets my quality has diminished. Been noticeing a slight flashing from a lose spur cutter. Should I be sizing these bullets? Below is my range data from first casted (best quality) bullets. They shot very well. Two different C.O.L & two different revolvers 6" barrel 1.475" C.O.L average velocity = 702 fps 1.445" C.O.L average velocity = 754 fps 2" barrel 1.475" C.O.L average velocity = 645 fps 1.445" C.O.L average velocity = 690 fps Please note: My cast bullet lead is considerably harder than any purchased Lead cast bullets. For that reason I may be losing velocity. Load data said I should be getting 825 fps. Very low recoil. Which is what I wanted. I was suprised to see the 50 fps increase with only a difference in the depth I seated the bullet. I seated them shorter than spec only becase the crip ended up on top of a tumble lube ridge. Lead fouling seems minimal. By comparison Winchester (white box) 130 FMJ 6" barrel average velocity = 779 fps 2" barrel average velocity = 680 fps Looking for some old timer advice. Thanks
__________________
Dad !!! "It's only going to be perfect if you do it yourself." - my teenage daughter Dad !!! "I'm not scared" My Cancer fighting daughter." Cancer Sucks NRA - Life Member |
March 6, 2013, 10:09 PM | #2 |
Senior Member
Join Date: March 30, 2011
Location: Lompoc California
Posts: 274
|
What's the standard deviation in the velocity?
What kind of accuracy are you getting? If it's not grouping well, then you may want to look at other things like sizing the bullets. Did you slug your barrel? You may also want to go with a softer alloy at the velocities you're trying to run at. |
March 6, 2013, 10:24 PM | #3 |
Senior Member
Join Date: December 20, 2009
Location: Texas Gulf Coast
Posts: 728
|
Correct me if I'm wrong, but I thought that the Lee Tumble lube bullets were to be used as dropped from the mold. No sizing needed, Just lube 'em & go.
|
March 6, 2013, 10:42 PM | #4 | |
Senior Member
Join Date: March 4, 2006
Posts: 178
|
Quote:
|
|
March 6, 2013, 11:12 PM | #5 |
Senior Member
Join Date: April 16, 2011
Location: Georgia
Posts: 1,599
|
Tumble lube = cast and shoot.
|
March 7, 2013, 10:20 AM | #6 |
Senior Member
Join Date: January 28, 2013
Location: Land of 10,000 taxes
Posts: 211
|
Tumble lube molds are advertised as " Cast & Shoot"
After the first hundred bullet's the spur cutter on the mold loosened up and kinda buggered up the seam edge of the mold and I started seeing a little flashing on the bullet base. Some bullets are .0005" to .001" out or round. And I'm using a good caliper. I'll loan a micrometer from work and double check. I don't have the gear to slug the barrel. The problem is they shoot great. I'm shocked how good of a grouping I'm get out of my snubnose. Any recommendationd on how to clean an Aluminum LEE bullet mold ??? I was thinking about using brake cleaner. Any opinions ??? I don't know if I'm worrying about nothing or if I'm becoming addicted to the precision of reloading. I like my fingers and eyes just the way they are. Respect for reloading in a healthy thing.
__________________
Dad !!! "It's only going to be perfect if you do it yourself." - my teenage daughter Dad !!! "I'm not scared" My Cancer fighting daughter." Cancer Sucks NRA - Life Member |
March 7, 2013, 12:55 PM | #7 |
Senior Member
Join Date: August 23, 2011
Location: Trinity, Texas
Posts: 636
|
I size all of my cast bullets. Most of the time there is little resistance on the handle as I push the bullet through the sizer. Sometimes there is a good bit of resistance. After sizing I tumble lube with Alox and dry. Next they go into a box until needed. Anymore, all of the straight wall pistol bullets I shoot are cast.
If I'm not mistaken, and I usualy am, different alloys will drop different sizes. Also quench casting will produce a different size than air cooling. I size just to be sure I'm shooting what I think I'm shooting.
__________________
David Bachelder Trinity, Texas I load, 9mm Luger, 38 and 40 S&W, 38 Special, 357Magnum, 45ACP, 45 Colt, 223, 300 AAC, 243 and 30-06 |
|
|