The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools Search this Thread
Old June 14, 2018, 10:35 AM   #1
MeanMachete
Junior Member
 
Join Date: June 13, 2018
Location: Texas
Posts: 2
.338 Norma Brass

Greeting everyone,I am a newbie to the reload world as well. I shoot a Savage m110 BA Stealth in .338 Lapua Mag. with 24 in. barrel, and 9.3R twist. I came across Norma brass (new) I would like use, and words of advice (projectile, powder, load)?
Thanks
MeanMachete is offline  
Old June 15, 2018, 12:50 PM   #2
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 14,588
Welcome to the forum.

It sounds like you are simply looking for loading data. You will find good data at Hodgdon Reloading's site. All the bullet makers have data books and some give data away.

Beyond that, you need to have a purpose to pick a bullet, and then you find the data for it. If you gave more detail about what kind of shooting you do, that would help others make suggestions.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Benefactor Member and Golden Eagle
Unclenick is offline  
Old June 15, 2018, 02:42 PM   #3
RC20
Senior Member
 
Join Date: April 10, 2008
Location: Alaska
Posts: 4,673
A warning, Norma brass while the best really means you need to jump into some advance loading tecniques. Otherwise its going to break at the base after (5 rounds? Have no had Norma so don't have a measure)

The issue is re-sizing pushes the shoulder way back and stresses the brass at the base where it goes from thick to thin.

The solution is to do as little shoulder bump back (.002 to .003) as you can get consistent (so you don't wind up with .000)

To do that you need (my choice) a set of micrometers that measure down to .001 as well as the Hornady shoulder tool adaptor that lets you put that on the micrometer so you can see.

Doing the raise the ram with shell holder to flush with the sizer die then turn another quarter is going to ensure guished shell and a break.

Add in that the RCBS match dies are very nice as they allow you to put a bullet in a side slot and not load from the bottom. Forster is nice but you have to load from the bottom (its also more consistent on the micrometer movement/ settings but I like the RCBS better)


I will add in my two manuals that give you that what you need as a solid base. .

Hornady X as its got quite a few of the new powders, Sierra, dated in regards to newer powders but all the standard powders that can work.

Each has a wide choice of bullet styles. This allows you with the idea of never starting high end loads, to use those for other mfgs bullets (all bullets between mfgs are different to some degree even if they look the same)

Those books also list the gun and twist the loads were fired in.

What you need to define is what you are doing, long range target shooting is going to be a whole different list of bullets vs a hunting load.

Those two manuals also are a help when someone does list a load, you can cross check it to see where it is on the spread of low starting to hot end and if you want to start there as you really want to start 10% down from a hot load.

Is it a common powder or a one off that works for one person but is not normaly used in a given gun.

Powder mfgs just give you there powder and a generic bullet, much better off with the Manuals.

Powder sites are good for new powders and I just transfer that data into the manuals.
__________________
Science and Facts are True whether you believe it or not

Last edited by RC20; June 15, 2018 at 06:40 PM.
RC20 is offline  
Old June 16, 2018, 05:39 PM   #4
hseII
Member
 
Join Date: April 11, 2015
Posts: 28
Quote:
Originally Posted by MeanMachete View Post
Greeting everyone,I am a newbie to the reload world as well. I shoot a Savage m110 BA Stealth in .338 Lapua Mag. with 24 in. barrel, and 9.3R twist. I came across Norma brass (new) I would like use, and words of advice (projectile, powder, load)?

Thanks


Is the brass Norma branded.338 Lapua or is the Brass Norma branded .338 Norma?
hseII is offline  
Old June 16, 2018, 08:13 PM   #5
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 14,588
I would assume the former, as his gun is 338 Lapua, but the title can be read both ways.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Benefactor Member and Golden Eagle
Unclenick is offline  
Old June 17, 2018, 07:48 PM   #6
RC20
Senior Member
 
Join Date: April 10, 2008
Location: Alaska
Posts: 4,673
If its Norma brass of any type then its pretty costly and worth the effort to keep it firing for as long as you can.
__________________
Science and Facts are True whether you believe it or not
RC20 is offline  
Old Yesterday, 03:17 PM   #7
MeanMachete
Junior Member
 
Join Date: June 13, 2018
Location: Texas
Posts: 2
It is stamped .338 Lapua.
__________________
Si vis pacem, para bellum
MeanMachete is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:15 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.04762 seconds with 9 queries