The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools Search this Thread
Old August 25, 2008, 05:05 PM   #376
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Thanks for your response! It looks more like the first one (it has a really short barrel) but the grip is like the 2nd one.
Okay, sounds like you have a "J" frame Centennial (model 40). The Standard Catalog of S&W only list the serial numbers as 1 thru 30160 from 1952 till 1971.
To narrow it any further (short of getting the letter from S&W) you'll need to look for clues on the gun itself.

1. On the right side of the gun, there are screws holding in the side plate. If there are 4 of them then it was made 1952 - 1955. If only 3 screws then 1955 on. The one that was eliminated was up near the hammer.

2. In 1957 S&W started stamping the model numbers on the forward inside of the frame behind the yoke assembly. It's only visable when the cylinder is opened. If yours has "MOD 40" stamped there then it was made from 1957 on. If not then prior to 1957. There are usually some assembly numbers stamped there as well the serial number on later guns.

3. In 1966 S&W changed from the flat thumbpiece (to release the cylinder) to a more rounded one.
The model 36 in this picture has a flat thumbpiece (also called a "flat latch").
.

4. In 1968 the diamond shape in the center on the wood grips was eliminated. Of course, that doesn't apply to your pearl grips.

5. In 1971 the serial numbers received a 'L' prefix and in 1974 the Model 40 (Centennial) was discontinued. However, S&W has recently started producing them again.

Hope this helps,
Jim
laytonj1 is offline  
Old August 25, 2008, 08:00 PM   #377
atlbabs
Junior Member
 
Join Date: August 24, 2008
Posts: 3
Jim

Thank you for sharing your knowledge on this gun with me and I am now going to absolutely get the letter from S&W. I left the gun at the gunsmith to have the heavy spring replaced with a lighter gauge as i was finding i tended to shoot high with the heavy trigger pull and after firing it, decided if i lessened the pull, i might be a bit more accurate (and I would have a rather fashionable carry piece!)...I will check the screws and other identifying marks when i get it back.

My dad served in Korea until 1952 and with 4 digit sn/, i would like to think he got this when he got back...in any event, you've answered the important questions and i truly appreciate it.

take care and thanks again~Barbara
atlbabs is offline  
Old September 2, 2008, 07:23 PM   #378
SunGrasses
Junior Member
 
Join Date: September 2, 2008
Posts: 1
My Great-Grandmother's Very Old S&W 32

I recently inherited my great-grandmother's Smith & Wesson .32 caliber pistol from my father. He is 72 years old, and he inherited it when he was a teenager. He has never shot it. I'm sure it has very little monetary value, but it is the most valuable gun in my collection. I'm a 44 year old mom and feel honored to be the caretaker of her gun.

From what my father said, my great-grandmother carried it all the time, and she was quite a good shot. From the wear pattern, I think she was left-handed (Like me!). The handle is very worn and has very little of the "criss-cross" pattern left.

If anyone can help, I would love to know the approximate date that it was manufactured. It has a 4 digit serial number, 897x, on the bottom of the handle. The 5 1/2" long barrell is marked "32 long ctg." I can find no other markings. It is a 6-shot.

Any other info or insight that you may have would be wonderful.

Can't you just see the old lady with this in her apron pocket?

Thanks for the help.

Last edited by Glenn E. Meyer; November 30, 2013 at 11:47 AM.
SunGrasses is offline  
Old September 2, 2008, 10:21 PM   #379
carguychris
Senior Member
 
Join Date: October 20, 2007
Location: Richardson, TX
Posts: 7,523
Quote:
I recently inherited my great-grandmother's Smith & Wesson .32 caliber pistol from my father... If anyone can help, I would love to know the approximate date that it was manufactured. It has a 4 digit serial number, 897x, on the bottom of the handle. The 5 1/2" long barrell is marked "32 long ctg." I can find no other markings. It is a 6-shot.
Your revolver is a .32 Hand Ejector Model of 1903, sometimes known as a .32 Hand Ejector 2nd Model. According to the serial number range, your gun was made in 1903 or 1904.

That's a neat revolver with a neat story! You might want to contact S&w and get a factory letter. It might add some more details to the gun's story:

http://www.smith-wesson.com/webapp/w...ectionId=10504

Also, I think you may have measured the barrel length incorrectly. The Model of 1903 was available with a 3-1/2", 4-1/4", or 6" barrel. Yours looks too short to be the 6" barrel; it looks to me like the 4-1/4", which seems to be the most commonplace length for old .32HEs. The barrel length is measured from the end of the barrel to the front face of the cylinder (the revolving part).
__________________
"Smokey, this is not 'Nam. This is bowling. There are rules... MARK IT ZERO!!" - Walter Sobchak
carguychris is offline  
Old September 5, 2008, 07:59 PM   #380
mymojo34
Junior Member
 
Join Date: September 5, 2008
Posts: 1
help needed.

Hi all.

My father in law just gave me a couple of old guns from his collection. Among them was this neat lil old pistol that I'd love to know more about. Its a five shot and appears to be a .38 (although standard .38 rounds are too long to fit it). It has matching serno's on the handle & barrel: 59195

Any insight into this weapons history would be appreciated!


mymojo34 is offline  
Old September 5, 2008, 11:18 PM   #381
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
My father in law just gave me a couple of old guns from his collection. Among them was this neat lil old pistol that I'd love to know more about. Its a five shot and appears to be a .38 (although standard .38 rounds are too long to fit it). It has matching serno's on the handle & barrel: 59195

Any insight into this weapons history would be appreciated!
It's a S&W .38 Double Action 2nd Model. They were made from 1880 to 1884 with serial numbers from 4001 thru 119000.
Your gun is chambered for ".38 S&W" caliber which is shorter and less powerful than the current .38 Special that came out in 1899.

Jim
laytonj1 is offline  
Old September 6, 2008, 01:44 AM   #382
btadams
Junior Member
 
Join Date: September 6, 2008
Location: Union City TN
Posts: 4
S&W Model 10

I just bought a S&W model 10 from a coworker that he carried for a duty weapon in the early 80's. I would like to see if anyone can help me with when it was made. I know he said he had bought it used at the time. It is a smith modle 10-6 the searial number is 53233 and has R6 below it. This is stamped on the cylinder frame. Any help will be greatly appreciated.
Thanks in advance
adamsbt

Last edited by btadams; September 6, 2008 at 01:50 AM. Reason: not enough detail
btadams is offline  
Old September 6, 2008, 07:16 AM   #383
Whirlwind06
Senior Member
 
Join Date: March 3, 2006
Location: NE Ohio
Posts: 998
Model 10-5 C790XXX

Thanks
Whirlwind06 is offline  
Old September 6, 2008, 04:44 PM   #384
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
I just bought a S&W model 10 from a coworker that he carried for a duty weapon in the early 80's. I would like to see if anyone can help me with when it was made. I know he said he had bought it used at the time. It is a smith modle 10-6 the searial number is 53233 and has R6 below it. This is stamped on the cylinder frame. Any help will be greatly appreciated.
That looks like an assembly number. The serial number should have a "C" or "D" prefix or a number/letter/number (ex. 4D8901). It will be located on the underside of the grip butt. If the grips on it cover the bottom of the grip frame you will need to remove them to see it.


Quote:
Model 10-5 C790XXX
1965.

Jim
laytonj1 is offline  
Old September 6, 2008, 08:43 PM   #385
smith627
Member
 
Join Date: April 27, 2008
Location: Central Mississippi
Posts: 16
Any help would be appreciated on the date of manufacture of a S&W
617 .22 revolver with SN# CEJXXX. I'm guessing maybe the mid to late 1990's ? Thanks in advance.
__________________
NRA Life Member
Shoot Safely, Shoot Often, & Share Your Sport - Shooting USA
smith627 is offline  
Old September 6, 2008, 09:21 PM   #386
carguychris
Senior Member
 
Join Date: October 20, 2007
Location: Richardson, TX
Posts: 7,523
Quote:
617 .22 revolver with SN# CEJXXX. I'm guessing maybe the mid to late 1990's ?
Late 2000.
__________________
"Smokey, this is not 'Nam. This is bowling. There are rules... MARK IT ZERO!!" - Walter Sobchak
carguychris is offline  
Old September 8, 2008, 12:02 AM   #387
btadams
Junior Member
 
Join Date: September 6, 2008
Location: Union City TN
Posts: 4
S&W Model 10

I made a post a couple of days ago but I put the manufacture number instead of the serial number. The gun I have is a S&W model 10-6. It has a blued finish with a heavy barrel. The serial number is 2D89xxx. It also has the numbers B6, B24, B14 what are these numbers. I am trying to find out about when it was made.
Thanks in advance
BTADAMS
__________________
Shoot straight or die trying
btadams is offline  
Old September 8, 2008, 07:45 PM   #388
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
I made a post a couple of days ago but I put the manufacture number instead of the serial number. The gun I have is a S&W model 10-6. It has a blued finish with a heavy barrel. The serial number is 2D89xxx. It also has the numbers B6, B24, B14 what are these numbers. I am trying to find out about when it was made.
Thanks in advance
1978. The other numbers are assembly numbers.

Jim
laytonj1 is offline  
Old September 9, 2008, 12:28 AM   #389
btadams
Junior Member
 
Join Date: September 6, 2008
Location: Union City TN
Posts: 4
Thanks Jim you're a wealth of knowledge or have alot of books. I've read several of your posts and you always have the answer.
BTADAMS
__________________
Shoot straight or die trying
btadams is offline  
Old September 9, 2008, 08:27 PM   #390
Ignacio49
Senior Member
 
Join Date: September 17, 2002
Posts: 221
Hello Jim.
I bought this one today.

Blue model 36-1, round butt, 3" barrel, s/n J775xxx. Wood grips have same s/n (without the "J").

Appreciate your help.
Ignacio49 is offline  
Old September 9, 2008, 09:01 PM   #391
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Hello Jim.
I bought this one today.

Blue model 36-1, round butt, 3" barrel, s/n J775xxx. Wood grips have same s/n (without the "J").
That would be 1981.

Jim
laytonj1 is offline  
Old September 9, 2008, 09:11 PM   #392
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Thanks Jim you're a wealth of knowledge or have alot of books.
LOL, yeah... it's the books, but thanks for the compliment. The majority of the info I give (DOB's and gun ID's) comes right out of The Standard Catalog of Smith & Wesson. Available at finer book stores and gun shows.

Jim
laytonj1 is offline  
Old September 9, 2008, 10:03 PM   #393
Ignacio49
Senior Member
 
Join Date: September 17, 2002
Posts: 221
Thanks Jim.
Ignacio49 is offline  
Old September 11, 2008, 12:32 PM   #394
russp
Junior Member
 
Join Date: September 11, 2008
Posts: 1
S&W M&P Model 1899 Manufacture Date?

I have what appears to be a re-nickled S&W 1899 M&P revolver.
The serial number is 1756. Has two rows of dates on the
barrel with a Maltese Cross on both ends of the dates.

My email address is [email protected]

Thanks

Last edited by Glenn E. Meyer; November 30, 2013 at 11:47 AM.
russp is offline  
Old September 11, 2008, 10:25 PM   #395
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
I have what appears to be a re-nickled S&W 1899 M&P revolver.
You are correct. They were made from 1899 to 1902 with serial numbers 1 thru 20975. Your serial number of 1756 would be first year.
Neat gun with a lot of history as the first year of the K frame and the .38 Special cartridge.

Jim
laytonj1 is offline  
Old September 11, 2008, 11:56 PM   #396
btadams
Junior Member
 
Join Date: September 6, 2008
Location: Union City TN
Posts: 4
S&W Model 10

Is the model 10 made in 1978 rated for +p ammo

BTADAMS
__________________
Shoot straight or die trying
btadams is offline  
Old September 12, 2008, 01:06 AM   #397
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Is the model 10 made in 1978 rated for +p ammo
Yes. Per S&W, model 10's made from 1958 on are rated for +P.

Jim
laytonj1 is offline  
Old September 12, 2008, 02:41 PM   #398
Scott_MS
Junior Member
 
Join Date: September 12, 2008
Posts: 2
Model 686 SN= ACL3XXX It's one of the dash nothing models, so I assume in the 1982-83 timeframe
Scott_MS is offline  
Old September 12, 2008, 02:49 PM   #399
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
Model 686 SN= ACL3XXX It's one of the dash nothing models, so I assume in the 1982-83 timeframe
Yep, 1983.

Jim
laytonj1 is offline  
Old September 14, 2008, 02:00 PM   #400
range_rider13
Member
 
Join Date: July 10, 2007
Location: Tex-Mex Border
Posts: 38
Model 586 Born On Date?

a) .357 Magnum
b) 6" bbl
c) square grips
d) 6 shot
e) adjustable rear sight (no white outline) and red/orange insert ramp front sight
f) Serial #AEL6XXX
g) Mod. 586

__________________
"If you climb into the saddle be ready for the ride!"
range_rider13 is offline  
Reply

Tags
s&w 686

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:37 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.65670 seconds with 9 queries