The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Bolt, Lever, and Pump Action

Reply
 
Thread Tools Search this Thread
Old November 2, 2016, 12:37 PM   #1
jackstrawIII
Senior Member
 
Join Date: July 20, 2016
Location: Upstate NY.
Posts: 426
Marlin 1894 Extraction Issue

Hey,

I've got a (hopefully) simple problem. I got new Marlin 1894 recently. I "broke in" the rifle shooting few boxes of 44 Specials, with no problems. Then I switched over to a box of 44 Mags and with the first shot, the case got stuck in the chamber and wouldn't eject. And it was really stuck in there. I ended up having to stick a dowel down the barrel and pound it out.

I figured maybe the chamber was dirty, so I cleaned chamber and barrel well and headed back to the range. Once again, first shot with 44 Mag jammed the brass in there so tight, it had to resort to hammering a dowel again.

When I pull the brass out, they look mostly ok, but have a slight indentation about halfway up the wall of the case and some "skid marks" along the case wall.

Any ideas? Can I fix this, or should I send the gun back?
__________________
In God we trust.
jackstrawIII is offline  
Old November 2, 2016, 12:52 PM   #2
VoodooMountain
Senior Member
 
Join Date: July 1, 2014
Posts: 142
The magnum loads may be a bit hot and causing harder extraction
You may also still have a ring of buildup in the chamber from firing the specials first

A little of both problems can create this situation


.......on the other hand if you have a remlin the chamber might be really rough, out of round, sideways, filled with wasps, or who knows...
VoodooMountain is offline  
Old November 2, 2016, 01:09 PM   #3
James K
Staff
 
Join Date: March 17, 1999
Posts: 24,193
There could be any of several causes, some easy to fix, but some potentially leading to ruining the gun. I would recommend returning the rifle (best way is through the dealer you bought it from) enclosing a fired case and have them correct the problem under warranty.

Jim
__________________
Jim K
James K is offline  
Old November 4, 2016, 06:54 AM   #4
Salmoneye
Senior Member
 
Join Date: December 31, 2011
Location: Vermont
Posts: 1,976
The 'skid marks' can be checked easily...

Simply load a round half way, and then pull it out...The 'skids' are usually from a sharp edge on the inside of the receiver on the 'loading gate hole'...This is usually cured with a fine stone or emery cloth on the inside edge, and then cold bluing with a 'pen'...

I second the ring of crud...

Serious cleaning of the chamber, and then try a different brand of magnum loads...

Then you can always go from there if Warranty work is needed...
Salmoneye is offline  
Old November 11, 2016, 10:20 PM   #5
jrothWA
Senior Member
 
Join Date: November 11, 2006
Posts: 2,199
its the same as shooting ...

.22 Shorts in a .22 LR chamber and the firing .22 LR.

Clean the chamber with solvent and a pipe cleaner , may have to chuck ina drill and bore brush.
jrothWA is offline  
Old November 12, 2016, 06:42 AM   #6
mehavey
Senior Member
 
Join Date: June 17, 2010
Location: Virginia
Posts: 4,764
Quote:
...shooting [a] few boxes of 44 Specials....
Agree w/others above about the fouling ring being a [likely] culprit.

Pull the lever/bolt out; stand the receiver on end/muzzle down on a towel;
and scrub (and I do mean scrub back & forth) the chamber/throat with a
45cal bronze brush soaked in solvent.

Finally (after the cleaning) straighten out a paper clip; file one end to a point;
and use it to probe the chamber walls [like you would a case for incipient head
separation] for anything that doesn't feel absolutely smooth.

** This all assumes that the gun is actually not short-chambered...
After the cleaning/before reassembling, see if a fired case (even one
of your previously-stuck ones) can be pushed home in the chamber with
reasonable ease.

.

Last edited by mehavey; November 12, 2016 at 07:01 AM.
mehavey is offline  
Old November 12, 2016, 08:36 AM   #7
g.willikers
Senior Member
 
Join Date: September 28, 2008
Posts: 10,447
There are mildly abrasive cleaning pastes on the market for cleaning and smoothing chambers.
Check with the usual mail order places for them.
__________________
Walt Kelly, alias Pogo, sez:
“Don't take life so serious, son, it ain't nohow permanent.”
g.willikers is offline  
Reply

Tags
failure , help diagnose , lever action , marlin , marlin 1894

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:18 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2017 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09042 seconds with 10 queries