|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
November 1, 2012, 04:20 PM | #1 |
Member
Join Date: February 4, 2012
Posts: 71
|
breaking in a new clip or magazine
does anyone know of a way to break in a new clip or mag with out shooting alot of ammo?
|
November 1, 2012, 04:36 PM | #2 |
Senior Member
Join Date: October 19, 2005
Location: Tx Panhandle Territory
Posts: 4,159
|
True, some do get better with time and use, but if you get one that does not work at all when it's fresh out of the wrapper- it could be anybody's guess as to what will make the clip work properly.
And it's really OK if you just want to use the word clip- I think folks are finally coming around to the idea that: 1. Everybody knows what's being discussed. 2. So far nobody has been able to produce substantial evidence that they have deemed, appointed, elected, or annointed as a supreme speech police. I think it a terrible thing to remove all traces of uniqueness from such a unique culture as we enjoy as Americans. Language, regional dialect, accents- who has the right to take that away and make everyone the same? But anyway, if you end up with a clip that does not work well after a hundred or so rounds (and the thing is inexpensive by your standard) I guess one would have little to lose by fine filing or stoning of rough spots, swapping springs, or even turning the spring around in some cases.
__________________
Rednecks... Keeping the woods critter-free since March 2, 1836. (TX Independence Day) I suspect a thing or two... because I've seen a thing or two. |
November 1, 2012, 05:14 PM | #3 |
Senior Member
Join Date: September 19, 2012
Location: Somewhere out there
Posts: 184
|
Cycle rounds a few times then load the magazine to full capacity, and leave it that way for a week or so then you should be ready to go. (Sometimes the springs in magazines are kinda funny acting so be patient with them)
__________________
12 Gauge Fury! |
November 2, 2012, 07:40 AM | #4 | |
Junior member
Join Date: September 27, 2011
Posts: 382
|
Quote:
in my OPINION.., if one is too lazy and/or ignorant to learn proper nomenclature.., they should NOT be handling guns. once more.., just my OPINION. no "clip" or "magazine" needs a "break in", just use them as intended. several months ago i bought 20 still in original wrappers VietNam era 20 round Colt magazines, i load them full and empty them, never a "magazine" malfunction. |
|
November 2, 2012, 09:38 AM | #5 |
Member in memoriam
Join Date: April 9, 2009
Location: Blue River Wisconsin, in
Posts: 3,144
|
Whooee, som'un got up on the wrong side of the bed, stubbed his toe and had to drink cold coffee this morning.
Dump the magazine in a can of fuel oil or oil and let it soak for a bit. Then grab something to use like a plunger and push down on the follower to make sure it isn't grabbing on the sides or hanging up anywhere. A few cycles should free up any glitches if there are any. Blow it out with a compressor and use a solvent like a can of spray carburetor cleaner to clean the oil out and you most likely will be good to go. If you still have problems time to open up the magazine for a closer look. Stiffness isn't a malfunction but sticking is and not being able top load the magazine to capacity is. Keep in mind some magazines are a bit optimistic on how many rounds they say you can load and will be a round short. Live with it if the the magazine is otherwise functional.
__________________
Good intentions will always be pleaded for any assumption of power. The Constitution was made to guard the people against the dangers of good intentions. There are men in all ages who mean to govern will, but they mean to govern. They promise to be good masters, but they mean to be masters. --Daniel Webster-- |
November 2, 2012, 09:45 AM | #6 |
Senior Member
Join Date: August 27, 2010
Location: I've moved...
Posts: 233
|
Just for smiles:
__________________
"Let me live in my house by the side of the road and be a friend to man." |
November 2, 2012, 11:19 AM | #7 |
Senior Member
Join Date: June 19, 2012
Location: East Texas
Posts: 407
|
I've only done two things to "break in" magazines.
We had to take apart M9 magazines and clean what must have been congealed preservative out of the inside to make them work right. I had to leave SIG P226 magazines loaded for several weeks before the springs lightened up enough to where I could get all the rounds that it was supposed to hold in there without breaking a finger. |
November 2, 2012, 11:39 AM | #8 |
Senior Member
Join Date: October 17, 2006
Location: TX
Posts: 513
|
Just clean, including the spring, with Hoppe's inside and out. Let dry. You can wipe with a silicone cloth if you want.
Re clip vs. mag. I prefer mag. I have a buddy who was a Marine M-60 gunner in Vietnam and got to use his 1911 extensively as well. He calls mags clips. I don't correct him.
__________________
If you want to shoot...shoot...don't talk! Tuco USAF Munitions 1969-1992 RVN 1972-1973 |
December 1, 2012, 07:56 PM | #9 |
Junior Member
Join Date: October 1, 2012
Posts: 1
|
gretings yawl...
figered this were a good place to jump in sence were talking about cleps and all... i gotts these 30 rounds pmags... can i feal them up with rounds ands leave thim that way with no adverce effects on the spring... |
December 1, 2012, 08:06 PM | #10 |
Senior Member
Join Date: January 28, 2012
Posts: 215
|
Magazines don't require a break in. When I get new mags I load them and stick them in the safe.
To the poster who asked about keeping pmags loaded, yes, you can. Load 'em up. |
December 1, 2012, 10:33 PM | #11 |
Senior Member
Join Date: February 6, 2008
Posts: 181
|
Just load it and put it away.
|
December 2, 2012, 07:45 AM | #12 | |
Senior Member
Join Date: November 2, 2007
Location: Northern Orygun
Posts: 4,923
|
When I get new to me magazines I disassemble, clean and lube. Check for proper feeding and then consider it GTG.
Quote:
There is a difference. |
|
December 2, 2012, 09:00 AM | #13 |
Senior Member
Join Date: May 25, 2007
Location: South Florida
Posts: 924
|
With every new magazine, I disassemble them, deburr the feed lips, deburr the front edge of the mag where the bullet moves past in feeding.
Then I inspect and deburr the follower, smoothing any rough edges or sharp points (or casting flash / sprue tag if its a molded follower) & treat it with a dry lubricant. The entire exterior and interior of the mag is cleaned & given a thin coat of dry lubricant. Re-assemble & GTG. Doing this, has resulted in virtually never having any mag related problems. Roger
__________________
Trigger control + Breath control + Sight alignment = Gun Control. http://www.hrpclub.info/ NRA Smallbore Prone Master, High Power Master |
December 2, 2012, 09:54 AM | #14 |
Senior Member
Join Date: September 30, 2012
Location: tennessee
Posts: 119
|
If it ain't broke don't fix it goes a long way for most things. However, I always deburr anything rifle or mag related. It can't come back to bite you later if it's not there. Just my humble offering.
|
December 2, 2012, 11:41 AM | #15 |
Staff in Memoriam
Join Date: November 13, 1998
Location: Terlingua, TX; Thomasville, GA
Posts: 24,798
|
After seventy-some years of hearing folks calling magazines clips, I've quit worrying about it. Life is too short to give a hoot about trivia. Picking fly-poop out of pepper is not a remunerative career choice.
And this is the first time I've ever heard anybody wonder about breaking in a mag. "Learn" something new, every day. |
December 2, 2012, 02:26 PM | #16 |
Member in memoriam
Join Date: April 9, 2009
Location: Blue River Wisconsin, in
Posts: 3,144
|
Y'all don't break in your clips way down there in the great country of Texas? I am shocked, just pure plumb befuddled shocked, that is all I can say, just shocked I tell ya.
__________________
Good intentions will always be pleaded for any assumption of power. The Constitution was made to guard the people against the dangers of good intentions. There are men in all ages who mean to govern will, but they mean to govern. They promise to be good masters, but they mean to be masters. --Daniel Webster-- |
December 2, 2012, 02:30 PM | #17 |
Senior Member
Join Date: July 21, 2011
Location: Idaho
Posts: 7,839
|
I've never had to break in a magazine. either your magazine has a problem interfacing with the gun or it does not, repeated use should not fix that. as long is the magazine is properly lubed then there shouldn't be a need for breakin.
a clip is a simple 1 or 2 piece metal strip that allows for rapid reloading. they wear out with use....not the other way around.
__________________
ignore my complete lack of capitalization. I still have no problem correcting your grammar. I never said half the stuff people said I did-Albert Einstein You can't believe everything you read on the internet-Benjamin Franklin |
December 2, 2012, 02:46 PM | #18 |
Senior Member
Join Date: March 15, 2010
Posts: 8,237
|
Ok the clip vs. magazine thing is just ridiculous.
If someone says clip along with a type of weapon that takes a magazine I AM SMART enough to know what they are talking about. To the question at hand, if a magazine doesn't function properly and you have some basic mechanical ability, many can be tweaked and otherwise coerced into functioning.
__________________
Woohoo, I’m back In Texas!!! |
December 2, 2012, 08:48 PM | #19 | |
Member in memoriam
Join Date: April 9, 2009
Location: Blue River Wisconsin, in
Posts: 3,144
|
Quote:
__________________
Good intentions will always be pleaded for any assumption of power. The Constitution was made to guard the people against the dangers of good intentions. There are men in all ages who mean to govern will, but they mean to govern. They promise to be good masters, but they mean to be masters. --Daniel Webster-- |
|
December 3, 2012, 08:31 AM | #20 | |
Senior Member
Join Date: November 2, 2007
Location: Northern Orygun
Posts: 4,923
|
Quote:
A guy asks me if I have any clips for a No4 Enfield. I say "sure, come on over and I'll give a few". He shows up and is ****** I'm not giving him magazines. |
|
December 3, 2012, 11:50 AM | #21 |
Senior Member
Join Date: July 21, 2011
Location: Idaho
Posts: 7,839
|
I agree with madcrate. also the OP did not specify what guns he is using said clips and mags for. the entire dictionary discussion here is started from one person taking offense at at a statement that was never made. a vast majority of guns have magazines however that does not mean that they do not also use clips nor does a question involving both terms require a lecture on terminology.
my post though it contained basic definitions was not meant to chastise or add to the existing discussion. I was merely pointing out that clips have virtually no area of improvement with use do to their simplistic design features.
__________________
ignore my complete lack of capitalization. I still have no problem correcting your grammar. I never said half the stuff people said I did-Albert Einstein You can't believe everything you read on the internet-Benjamin Franklin |
December 3, 2012, 01:58 PM | #22 |
Senior Member
Join Date: March 15, 2010
Posts: 8,237
|
I didn't have a problem with the people explaining the correct usage of the term, I don't think someone should be chastised over it.
Many don't know the proper terms for certain car parts, does that mean they don't deserve the right to own and operate one. I lot of people think there's only one accelerator in a car. Fix your mags or throw them away.
__________________
Woohoo, I’m back In Texas!!! |
|
|