August 30, 2014, 10:14 PM | #1 |
Senior Member
Join Date: February 28, 2014
Location: Washington (Dry Side)
Posts: 116
|
Counter Bore Question
Does anybody have experience with deeply "inches" counterbored rifles? I'm building a pistol caliber bolt rifle and I don't want to deal with the tax stamp for a short barrel so I was was wondering if there were any tests on barrels with about 4" of essentially free bore at the muzzle end. Accuracy results?
|
August 30, 2014, 10:26 PM | #2 |
Junior member
Join Date: February 2, 2010
Posts: 6,846
|
Don't know what round you're planning to use but I've found 16" of barrel is still advantageous even with a 9x19mm.
|
August 30, 2014, 11:22 PM | #3 |
Senior Member
Join Date: December 26, 2004
Location: Louisville KY
Posts: 13,806
|
I'm not sure what purpose this would serve.
|
August 30, 2014, 11:38 PM | #4 |
Senior Member
Join Date: February 28, 2014
Location: Washington (Dry Side)
Posts: 116
|
Because I want 12" of rifling and need 4 more inches of barrel length. SBR is not an option.
|
August 30, 2014, 11:46 PM | #5 |
Senior Member
Join Date: November 18, 2005
Location: On the Santa Fe Trail
Posts: 8,248
|
Sounds like a waste of 4" of fps to me. If you want a 12” barrel cut it off at 12” and add a 4" flash suppressor permanently affixed. That's what they do with AR-15 rifles, bug it's usually just a 2" flash suppressor.
__________________
NRA Life Member |
August 31, 2014, 01:34 AM | #6 |
Senior Member
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,424
|
No point in doing so. It's just a waste of barrel length, and a great way to introduce undesirable variables.
Chop the barrel where you want it, thread it, and permanently install a muzzle device (brake, comp, suppressor, whatever...).
__________________
Don't even try it. It's even worse than the internet would lead you to believe. |
August 31, 2014, 04:16 AM | #7 |
Senior Member
Join Date: February 15, 2009
Posts: 8,927
|
Bloop tubes have been used on rifles for many years with great success. It increases sight radius to make the front sight appear sharper and better in focus:
http://www.accurateshooter.com/gear-...om-norm-houle/ https://www.google.ca/search?q=bloop...w=1187&bih=552 Anschutz made .22 rimfire match rifles with them; did very well in the Olympics. I've seen 'em on some high power match rifles 10 inches long. While one changes the resonant frequency of the barrel, it's still very repeatable from shot to shot so accuracy's not impaired. I don't know where folks get the idea that adding anything to the muzzle will add another variable. All barrels, with or without something hanging onto their muzzles, vibrate with the same frequencies and harmonics thereof depending on their material, shape and length. It's the same for every shot fired. Adding something to the muzzle will change the frequencies it vibrates at, but they'll be at the new frequency for every shot thereafter. There are no variables in that new frequency; the physical properties of the barrel and its attachments don't change from shot to shot. Just counterbore the barrel back as far as you want to the diameter the barrel can withstand. It'll work the same as bloop tubes and not come loose. And you want 12 inches of rifling? Why? Starting from the breech face, chamber mouth or where to the end of it? Last edited by Bart B.; August 31, 2014 at 11:29 AM. |
September 1, 2014, 10:35 AM | #8 |
Senior Member
Join Date: May 27, 2007
Posts: 5,261
|
I have a featherweight 270 Win barrel on a pre 64 that someone must have fired a round through it when there was mud or something in the bore. The bulge was within two inches of the muzzle. Would always get a flyer.
Gunsmith reamed the last two inches to remove the rifling. So I have a rifled smooth bore rifle! I have only put a Lyman 48 on the thing, it is very handy, but since the front is a bead, can't say it is a target rifle, it shoots around 3 MOA at 100 yards. But the group is round. Can't say it is a velocity champ. Code:
Pre 64 M70 100 grain PSP Remington Factory 21-Jan-03 T = 48 °F Ave Vel = 3055 Std Dev = 66 ES = 165 Low = 2982 High = 3147 N = 7 130 grain Nosler BT 55.0 grains H4350 wtd R-P cases WLR OAL 3.30" 24-Mar-04 T = 70 °F Ave Vel = 2839 Std Dev = 33 ES = 123 Low = 2784 High = 2907 N = 19 I have buds with bloop tubes on their AR 15 actioned 6.5 Grendels. These guys assemble the rifle each match, shoot outstandingly with the things. I don't trust bloop tubes, but the guys around me shoot good scores with the things. Last week, an AMU shooter next to me shot a perfect small bore prone score, with irons, and his rifle must have had two extra feet of bloop tube. It did not hurt that his eyes are great, he probably sees with naked eyes, what I see through a scope!
__________________
If I'm not shooting, I'm reloading. |
September 1, 2014, 08:45 PM | #9 |
Senior Member
Join Date: August 1, 2010
Location: Tampa Bay
Posts: 4,556
|
I'm not understanding how having a long amount of rifling missing would not affect accuracy.
Couldn't the expanding gases push past the bullet before it exits the muzzle, or at least push the base unevenly? Just seems that a bullet with the ability to wobble inside the bore would be detrimental... If not, where's the limitation? Surely, a couple inches of rifling and two feet of counterbore wouldn't cut it...
__________________
Remington 700/Savage Rebarreling /Action Blueprinting 07 FFL /Mosin-Nagant Custom Shop/Bent Bolts Genuine Cerakote Applicator www.biggorillagunworks.com |
September 2, 2014, 07:55 AM | #10 |
Senior Member
Join Date: February 15, 2009
Posts: 8,927
|
Gas flow and direction around bullets in bloop tubes is very repeatable from shot to shot. If not, how do such things allow rifles to win matches and set records? If it wasn't, their poor effect on accuracy would convince top ranked competitors not to use them.
|
September 5, 2014, 05:02 PM | #11 |
Senior Member
Join Date: February 28, 2014
Location: Washington (Dry Side)
Posts: 116
|
Thanks I'll look into the bloop tubes.
|
|
|