The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Semi-automatic Forum

Reply
 
Thread Tools Search this Thread
Old June 13, 2018, 08:00 PM   #1
RemoWilliams
Junior Member
 
Join Date: June 24, 2012
Posts: 10
10MM Valor

I picked up a new 10MM Valor today. Very nice pistol, It looked perfect at the gun store, but when I got it home and made a more through inspection, I found a machining scar across the surface of the slide near the firing pin. I guess I will be making a trip back to the store tomorrow, but after reading about the quality of the craftsmanship with this series of pistol, it is disappointing to have to deal with something that should have been caught by the machinist when the part was made. Other than that, the slide was smooth and tight, the trigger pull is very nice, and the outer finish was excellent.
Attached Images
File Type: jpg Slide_1.jpg (42.2 KB, 104 views)
RemoWilliams is offline  
Old June 13, 2018, 10:26 PM   #2
HisSoldier
Senior Member
 
Join Date: August 9, 2007
Location: Oregoncoast
Posts: 1,658
It's brand new? Is it a "Blem"? They used to sell blems at one time, maybe still do, reports were that the actual blemishes were hard to find. It's been too long, but I seem to recall there being a serial number tag on blems, and tehy sold several hundred dollars below normal price.
__________________
CNC produced 416 stainless triggers to replace the plastic triggers on Colt Mustangs, Mustang Plus II's, MK IV Government .380's and Sig P238's and P938's. Plus Colt Mustang hardened 416 guide rods, and Llama .32 and .380 recoil spring buttons, checkered nicely and blued.
HisSoldier is offline  
Old June 14, 2018, 12:56 AM   #3
FrankenMauser
Senior Member
 
Join Date: August 25, 2008
Location: Where you wish you were
Posts: 10,935
It's fine.
Shoot it and move on with life.

A: The store had nothing to do with the "problem". Leave them out of it.
B: Sending it back to the manufacturer just makes them spend money on a non-issue (if they even do anything about it), which drives up the cost of future purchases.

It's fine.
Shoot it and move on with life.
Don't be anal-retentive about trivial crap like a minor machining mark that doesn't affect function and can't even be seen unless you're looking for it.
__________________
Don't even try it. It's even worse than the internet would lead you to believe.
FrankenMauser is offline  
Old June 14, 2018, 05:47 AM   #4
straight-shooter
Senior Member
 
Join Date: June 12, 2007
Location: North Central Indiana
Posts: 412
$1,500 dollar gun, I wouldn't be too happy either. Thus the reason I always inspect before taking it home.

Even though it won't affect function or maybe it won't seeing how the brass is going to be sliding across that imperfection during ejection, I would demand perfection for that kind of dollar spent.

Since you left the gun shop with it, it's pretty much now on the manufacturer to take care of you. Exactly the reason they have their warranty so I'd make use of it. May be some time without your new purchase but in the end it will be worth it and you'll be glad you did.
straight-shooter is offline  
Old June 14, 2018, 10:42 AM   #5
RickB
Senior Member
 
Join Date: March 1, 2000
Location: Western WA
Posts: 7,474
I wouldn't be happy with the appearance, but if the gun is a good, reliable shooter, you risk messing that up with a slide change.
They messed up once, why give them the opportunity to do so again?
__________________
Runs off at the mouth about anything 1911 related on this site and half the time is flat out wrong.
RickB is online now  
Old June 14, 2018, 12:24 PM   #6
RemoWilliams
Junior Member
 
Join Date: June 24, 2012
Posts: 10
I am the kind of guy that never gets rid of any gun I buy. The only time that a slight imperfection on the breech face would bother me is if I was going to sell it. That is when the potential buyer, who normally wouldn’t care at all about the mark would make a big deal about it to try to knock down the selling price. The outside of the gun is perfect, and as was pointed out, sending it back to the factory may leave me with a slide that is not mated as well to the frame as this one seems to be, or worse, they just buff out the breech face that leaves a slight depression in the face. I haven’t shot it yet, so if they were willing to just make an even trade for a different new one, then I will do it. Otherwise, I’ll just live with it. And make a much greater effort inspecting my next pistol before I walk out the door. Sadder but wiser. Thank you all for your input.
RemoWilliams is offline  
Old June 14, 2018, 12:29 PM   #7
gbclarkson
Senior Member
 
Join Date: January 4, 2014
Location: None of yer business, sonny
Posts: 269
Remo,
Is the rear sight is off-center?
gbclarkson is offline  
Old June 14, 2018, 05:11 PM   #8
RemoWilliams
Junior Member
 
Join Date: June 24, 2012
Posts: 10
No, it is centered. The photo just makes it look like it is off center.
RemoWilliams is offline  
Old June 15, 2018, 09:02 AM   #9
robert1804
Member
 
Join Date: May 5, 2015
Posts: 39
I've inspected lots of guns before purchase and like to think I'm fairly good at it. But I easily see how something like this could easily be missed. You just wouldn't expect a big tool mark on the breech face. The mark would bother me unless I had bought the pistol at a steep discount. I would send that photo to DW customer service. They would likely replace that slide for you unless that pistol was a blem because of that mark.
__________________
They'll have to pry my Illudium Q36 Explosive Space Modulator from my cold dead gripping appendages.
robert1804 is offline  
Old June 15, 2018, 10:53 PM   #10
dakota.potts
Senior Member
 
Join Date: February 25, 2013
Location: Broward County, Florida
Posts: 2,846
As a machinist I would not be happy about that either and I would be loathe to let something like that leave my shop.

On the other hand you still have well over 90% case support on the breech so if their engineering/QC decided it was safe and you bought it as a blem then that's all there is to it.
__________________
Please consider taking a look at my website Potts Precision.
Recent interesting articles include:
Why a .22LR is an Important Tool
And A Very Cool Model 70 .35 Whelen
dakota.potts is offline  
Old June 19, 2018, 10:32 AM   #11
RemoWilliams
Junior Member
 
Join Date: June 24, 2012
Posts: 10
As a follow-up on this issue with this pistol, I purchased this pistol from a local dealer. I purchased it as a new, first class condition pistol, not a blemished pistol. I did not pay a discounted price for the pistol. I ordered it from him, it came in, and I bought it. When I discovered the issue, I went back and asked if he could help. He didn’t have another one in stock, so he said he would see what he could do. Long story short, he got another one in, called me, and asked if I would want to make an exchange. I told him yes, and that I had not fired the pistol. I went back, filed out the paperwork, and made the exchange. He would send the pistol back to the factory to have them repair it. The point to the story is that while you may find a better price on line, doing business in person face to face has value. The dealer did right by me, and he did it to keep earning my business. Will I go back to him? You bet.
RemoWilliams is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:50 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05501 seconds with 10 queries