The Firing Line Forums

Go Back   The Firing Line Forums > The Conference Center > General Discussion Forum

Reply
 
Thread Tools Search this Thread
Old January 3, 2020, 08:41 PM   #1
Doc Holliday 1950
Senior Member
 
Join Date: June 16, 2014
Location: Bout as south as it gets
Posts: 1,220
damage by squib repaired

I just got my G43x back from Glock. They replaced the barrel for $20.00.
Went to my range & found that it shoots a tad lower than the the original but that's to be expected. I added a laser guide rod as a Holiday treat for myself & I've been practicing quick placement without aiming saving 2 or 3 seonds to fire. I found that my accuracy is in the center of the target not in tight groups but i'm hitting the the meat of the target.The accuracy is good up to 25 feet & I have no complaints & that's without using the laser. The Firing Line is a font of wisdom & information. Just ask the question in the correct manner & you will get some super information. Thanks everyone who shared Squibs with me.
One heck of a way to start the New Year.
If any of the responders have had similar actions please feel free to add your comments to my post.
__________________
Shoot well and be Accurate,

Doc
Doc Holliday 1950 is offline  
Old January 5, 2020, 02:07 AM   #2
44 AMP
Staff
 
Join Date: March 11, 2006
Location: Upper US
Posts: 20,850
I will add this, anytime you are shooting and ANYTHING not "usual" happens, then training is done, plinking is done, that gun is done, until you find out what happened, and why.

If you have to cycle the slide, by hand, you're done, until you have cleared the pistol, AND checked the bore.

Tap, rack, bang is for when people are shooting at you. (and for planned failure drills) an automatic response may be "good training" but its poor safety.

Tap, rack, KA-BOOM is possible if you don't STOP, and make sure the bore is unobstructed.

I've never had a squib with rimfire ammo, though I have had many fail to fire, and some complete duds. Been reloading since the early 70s, and to date, I have had one squib (and it was my fault) a couple years ago. And, it was in a Desert Eagle .44 Mag.

Apparently somehow, Murphy got the best of me and the round had no powder. Slide did not cycle. Bullet stuck in the barrel just ahead of the chamber. It happened on the first round from a box I had loaded some months previously. Scared the crap out of me, and made me really worried about the rest of the rounds in the box. Desert Eagle retired for the day...

Some time later, I did shoot that ammo, from a Super Blackhawk, paying extra attention for anything out of the norm. They were all fine. To this day, I don't know why it happened, first time in over 35 years anything like that had ever happened, to me. Humbling, and proof I am not immune to mistakes.

ANYTIME anything is "off" STOP, and check the gun especially the barrel. If you're being shot at, then, of course all bets are off, but if you aren't being shot at, NOTHING is more important that making sure the gun is completely ok before the next round gets fired. And, if it means losing a match, or having the worlds greatest trophy get away, that's what it means.

My opinion, and worth what you paid for it.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better.
44 AMP is offline  
Old January 5, 2020, 08:03 AM   #3
Sevens
Senior Member
 
Join Date: July 28, 2007
Location: Central Ohio
Posts: 11,449
The procedure you described above is what was ingrained in me from the earliest shooting days of my life when I started as a teenager. And I began my handloading career only a handful of months after I started shooting.

It wasn’t until the training trends became popular a decade or more later that it became (seemingly?) the norm to just speed through any form of a stoppage like an industrial machine designed for throughput and it is an internal conflict that I have had for the latter half of my short three decades as an enthusiast handgunner.

I would say that I have chosen to stick to my roots and approach a stoppage methodically but to be honest, I don’t believe I have chosen it, it was more developed and I haven’t altered that development.

It would limit my success in competition and would get be yelled at in an intense training class I’m sure.
__________________
Attention Brass rats and other reloaders: I really need .327 Federal Magnum brass, no lot size too small. Tell me what caliber you need and I'll see what I have to swap. PM me and we'll discuss.
Sevens is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:04 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.04037 seconds with 8 queries