The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools Search this Thread
Old March 29, 2019, 05:56 PM   #1
GarandTd
Senior Member
 
Join Date: June 15, 2016
Location: Rural PA
Posts: 1,639
Ruger Mark III 22/45 stiff bolt and bolt stop lever

I replaced the mag disconnect safety with a TandemKross hammer bushing. Now the bolt is getting slowed down by something and the bolt stop lever is very stiff unless I relieve it while holding the bolt back. The gun fires and ejects, but now needs a bump to finish the bolt returning to battery. I can't figure out what's causing the problem. Pistol still shoots accurately.
__________________
22lr, 20 gauge, 8mm Mauser, 35 Remington, 30-06, 5.56x45/223, 9mm, 380acp
GarandTd is offline  
Old March 29, 2019, 06:00 PM   #2
GarandTd
Senior Member
 
Join Date: June 15, 2016
Location: Rural PA
Posts: 1,639
Here is a picture of the bolt after firing a round and a picture of the 1/2 loaded round in chamber.
Attached Images
File Type: jpg rps20190329_185801_765.jpg (145.1 KB, 71 views)
File Type: jpg rps20190329_185822_270.jpg (96.4 KB, 62 views)
__________________
22lr, 20 gauge, 8mm Mauser, 35 Remington, 30-06, 5.56x45/223, 9mm, 380acp
GarandTd is offline  
Old March 29, 2019, 06:04 PM   #3
GarandTd
Senior Member
 
Join Date: June 15, 2016
Location: Rural PA
Posts: 1,639
10 rounds at 50 yards. 8 of them were within the space of a target clay. These, today were the 1st rounds I've fired at 50 yards with this pistol. Remington Thunderbolt bulk.
Attached Images
File Type: jpg rps20190329_190321_609.jpg (148.8 KB, 51 views)
__________________
22lr, 20 gauge, 8mm Mauser, 35 Remington, 30-06, 5.56x45/223, 9mm, 380acp
GarandTd is offline  
Old March 30, 2019, 05:50 AM   #4
Mobuck
Junior member
 
Join Date: February 2, 2010
Posts: 6,846
Something wasn't re-assembled correctly.
Mobuck is offline  
Old March 30, 2019, 08:27 AM   #5
GarandTd
Senior Member
 
Join Date: June 15, 2016
Location: Rural PA
Posts: 1,639
At this point I've gone through the process several dozen times. It seems to me all parts are in where they belong. I suspect something got tweeked ever so slightly.

I did have an "oops" moment the last disassembly before installing the hammer bushing. I was having difficulty removing the barrel/receiver from the grip frame. Per manual instructions, I tapped with a rubber mallet several times before realizing that I still had a magazine in the grip frame. Once the magazine was out, the receiver came right off. It was a rubber mallet and I wasn't pounding on it like a rail spike, but that is the only thing I can think of that may have goofed something up. It's ironic since part of the reason for the modification was to eliminate the magazine from the takedown process.
__________________
22lr, 20 gauge, 8mm Mauser, 35 Remington, 30-06, 5.56x45/223, 9mm, 380acp
GarandTd is offline  
Old March 30, 2019, 12:50 PM   #6
GarandTd
Senior Member
 
Join Date: June 15, 2016
Location: Rural PA
Posts: 1,639
I'm really not sure what I did differently, but on takedown/reassembly #57, the bolt seems to be returning to battery uninhibited. I'll update after a test at the range.
__________________
22lr, 20 gauge, 8mm Mauser, 35 Remington, 30-06, 5.56x45/223, 9mm, 380acp
GarandTd is offline  
Old March 30, 2019, 05:24 PM   #7
GarandTd
Senior Member
 
Join Date: June 15, 2016
Location: Rural PA
Posts: 1,639
I wouldn't say I figured it out, but after many, many series of messing with the Ruger, the pistol is running proper now. I had one fail to lock-up in the 1st of 6 mags. The rest went smooth.
2 green targets: left was first mag, right was 2nd
Paper plate: 2mags (clover sticker is 1.5")
All at 25 yards from bench, Remington Thunderbolt bulk
Attached Images
File Type: jpg rps20190330_182027_149.jpg (154.9 KB, 29 views)
File Type: jpg rps20190330_182043_802.jpg (155.1 KB, 23 views)
__________________
22lr, 20 gauge, 8mm Mauser, 35 Remington, 30-06, 5.56x45/223, 9mm, 380acp
GarandTd is offline  
Old April 2, 2019, 08:31 AM   #8
SGW Gunsmith
Junior member
 
Join Date: December 31, 2014
Location: Northwest Wisconsin
Posts: 285
Those who you bought the hammer bushing from do not make those bushings, they just resell those that they have made by someone else.
Quality Control is therefore NOT on the sellers menu. When a faulty part is returned, you get a replacement from the very same batch.
In the past, and they've admitted this, on another forum in a post that I have a hard copy of, that they have gotten some of these hammer bushings from the company that makes 'em, that are too friggen long and the left end of the bushing rides/drags on the inside face of the safety plate. That effect will slow down the forward motion of the bolt. Not good. Check that for yourself.

I have seen this multiple times and have replaced their hammer bushings with a "good" properly fitted, hammer bushing on a regular basis. Consider this. Ruger uses manufacturing tolerances. What that means when replacing hammer bushings, is, "one size does not fit all".
The bushings I use are fit to each specific hammer bushing hole diameter and the "over-all length" is closely held, and often adjusted, so it doesn't drag on the safety plate.
SGW Gunsmith is offline  
Old April 2, 2019, 09:14 AM   #9
GarandTd
Senior Member
 
Join Date: June 15, 2016
Location: Rural PA
Posts: 1,639
SGW Gunsmith, thanks for that response. It seems to be working much better now. I may have to take a closer look next time I have it apart. I imagine if the overall length is an issue, there will be marks on the inside face of the safety plate, right?
__________________
22lr, 20 gauge, 8mm Mauser, 35 Remington, 30-06, 5.56x45/223, 9mm, 380acp
GarandTd is offline  
Old April 7, 2019, 10:08 AM   #10
SGW Gunsmith
Junior member
 
Join Date: December 31, 2014
Location: Northwest Wisconsin
Posts: 285
Yes, you should see some bluing wear, or if stainless, there will be rub marks from that end of the bushing.
SGW Gunsmith is offline  
Old January 16, 2020, 05:12 PM   #11
GarandTd
Senior Member
 
Join Date: June 15, 2016
Location: Rural PA
Posts: 1,639
UPDATE: I thought I had gotten this Ruger 22/45 running properly with the TK hammer bushing, but I was wrong. It's been plagued with several jams per magazine for quite a while now. I finally decided the benefits offered by the bushing were not worth the problems it created. I returned the Ruger to stock form and it is now functioning smoothly without the jamming. Relatively inexpensive lesson learned.

This Ruger is a target pistol/plinker/range toy for me. Although I'm not a big fan of the mag disconnect, for this pistol and it's uses, it doesn't bother me to have it reinstalled. Whatever differences the bushing made in the trigger pull were trivial. And, having torn this thing apart and put it back together so many times, the Xtra steps required for cleaning don't even phase me now. I think the one thing I'll miss the most is going to be the mags dropping free, but not that big of a deal. I'm glad to have it operating smoothly again and because of that, I expect to take it out more often.
__________________
22lr, 20 gauge, 8mm Mauser, 35 Remington, 30-06, 5.56x45/223, 9mm, 380acp
GarandTd is offline  
Old January 16, 2020, 06:56 PM   #12
Blindstitch
Senior Member
 
Join Date: April 14, 2013
Location: Milwaukee, Wisconsin
Posts: 2,685
Good to hear it's working again. I picked up a Mark 4 hunter in October and can't wait to get it back to the range. I've been shooting cci minimags but cycle thunderbolts in the mix and haven't noticed any difference.
__________________
NRA Lifetime Member
Blindstitch is offline  
Old January 16, 2020, 09:41 PM   #13
GarandTd
Senior Member
 
Join Date: June 15, 2016
Location: Rural PA
Posts: 1,639
The 1st time I let the bolt slam shut after restoring the gun to stock I could tell the problem was solved. The problems were definately not ammo specific. And so far, this pistol has not showed signs of being picky. Not picky as far as operating, accuracy varies from one brand to the next. It shoots 40gr CCI blazer exceptionally well and Thunderbolts impressively too. Armscor is ok. I have some federal and some 38gr CCI Blazer that I haven't tried in it yet. I'm confident the Blazer will perform. Time will tell on the Federal.
__________________
22lr, 20 gauge, 8mm Mauser, 35 Remington, 30-06, 5.56x45/223, 9mm, 380acp
GarandTd is offline  
Old January 17, 2020, 09:41 AM   #14
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 21,022
Try the CCI or Federal standard velocity 40-grain RN loads. You can even try CCI Green Tag which is intended for pistol, but which is reduced velocity to let guns get back on target faster during rapid fire. Overall, I've found the CCI and Federal standard velocity loads to do best in my Ruger pistols. The only thing that ever showed signs of grouping tighter for me were some CCI hollow points, but they would produce about one flier in every 8 shots, neutralizing the advantage to the rounds that grouped better. If I had ever figured out how to sort the bad ones out, I'd have had a new 50-yard load to use.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Benefactor Member and Golden Eagle
Unclenick is offline  
Old April 2, 2020, 03:16 PM   #15
SGW Gunsmith
Junior member
 
Join Date: December 31, 2014
Location: Northwest Wisconsin
Posts: 285
Quote:
Originally Posted by GarandTd View Post
UPDATE: I thought I had gotten this Ruger 22/45 running properly with the TK hammer bushing, but I was wrong. It's been plagued with several jams per magazine for quite a while now. I finally decided the benefits offered by the bushing were not worth the problems it created. I returned the Ruger to stock form and it is now functioning smoothly without the jamming. Relatively inexpensive lesson learned.

This Ruger is a target pistol/plinker/range toy for me. Although I'm not a big fan of the mag disconnect, for this pistol and it's uses, it doesn't bother me to have it reinstalled. Whatever differences the bushing made in the trigger pull were trivial. And, having torn this thing apart and put it back together so many times, the Xtra steps required for cleaning don't even phase me now. I think the one thing I'll miss the most is going to be the mags dropping free, but not that big of a deal. I'm glad to have it operating smoothly again and because of that, I expect to take it out more often.
The replacement hammer bushings intention was to replace the magazine disconnect, only. They don't have anything to do with trigger pull weight reduction. Sear angle work or a replacement sear will get that done for you.
How tightly did that replacement bushing fit into the hammer bushing hole? Was it tight or sloppy? Most all I've found involving that brand were quite loose and able to drift side to side.
SGW Gunsmith is offline  
Old April 2, 2020, 07:48 PM   #16
GarandTd
Senior Member
 
Join Date: June 15, 2016
Location: Rural PA
Posts: 1,639
The replacement was loose in the hammer bushing hole.
The pistol works better without it. I've been shooting alot more of it lately.
__________________
22lr, 20 gauge, 8mm Mauser, 35 Remington, 30-06, 5.56x45/223, 9mm, 380acp
GarandTd is offline  
Old April 2, 2020, 10:33 PM   #17
Jim567
Senior Member
 
Join Date: January 4, 2014
Location: NE FL
Posts: 655
When I installed my bushing then pistol jammed almost ever round.
I tried everything.
Upgraded extractors, recoil springs, removed the loaded chamber indicator.
Removing the bushing was the fix.
It was a huge waste of time and effort except that I now know the 22/45 inside and out.
Jim567 is offline  
Old April 3, 2020, 08:00 AM   #18
GarandTd
Senior Member
 
Join Date: June 15, 2016
Location: Rural PA
Posts: 1,639
Jim567, I had basically the same results as you.
__________________
22lr, 20 gauge, 8mm Mauser, 35 Remington, 30-06, 5.56x45/223, 9mm, 380acp
GarandTd is offline  
Old April 3, 2020, 08:08 AM   #19
ammo.crafter
Senior Member
 
Join Date: June 25, 2006
Location: The Keystone State
Posts: 1,967
Upgrading

If you are inclined to upgrade you Ruger, I suggest Volquartsen as a good source for quality products.
__________________
"Peace is that brief glorious moment in history when everybody stands around reloading".
--Thomas Jefferson
ammo.crafter is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:17 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.06233 seconds with 9 queries