The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Bolt, Lever, and Pump Action

Reply
 
Thread Tools Search this Thread
Old October 13, 2012, 08:54 PM   #1
LaramieHirsch
Junior Member
 
Join Date: October 13, 2012
Posts: 1
Nagant Corrosion

Howdy, all.

Just learned about this forum today. I think I have an urgent question.

I have a Mosin Nagant. I shot 20 military-grade rounds through it last Friday.

I took it home and cleaned it, but there was a lot going on in the house, and I couldn't clean it to greasy perfection. There was a tiny bit of black on the cotton when I finished up.

A week has passed.

I intend to clean the gun again tonight. But after a week of cleaning it last, do you fellas think there is severe corrosion damage in the barrel, now?

Is the gun safe to shoot?

Should I take it to a gunsmith, now?

Time to clean it again.


Ignorant of gun cleaning,
-L.H.
LaramieHirsch is offline  
Old October 14, 2012, 08:04 AM   #2
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 41,374
There's no way to answer that question adequately.

You have to make that determination yourself through examination.

Corrosion from corrosive primed ammunition depends on the amount of moisture in the air (humidity) to activate it.

If the ambient humidity is low enough, the corrosion won't happen. If it's high enough, it can happen very, very quickly.

The only way to adequately remove corrosive fouling is with hot soapy water. The soap removes any oil or grease that might be in the bore, and the hot water dissolves the fouling.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old October 14, 2012, 09:37 AM   #3
amx4080
Member
 
Join Date: December 10, 2011
Posts: 67
Corrosion is due to salts in the power and primer. To neutralize the salts, use ammonia. Windex is a common source a lot of people use. Always assume surplus ammo in 7.62x54r is corrosive.
__________________
The GunStockMarket
amx4080 is offline  
Old October 14, 2012, 12:14 PM   #4
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 41,374
Ammonia does NOT neutralize potassium chloride.

Ammonia contains a significant portion of water, which dissolves the salts. Ammonia also can remove oils and grease which is a benefit.

However, ammonia can contribute to hydrogen embrittlement of the barrel steel over time.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old October 14, 2012, 12:41 PM   #5
DnPRK
Senior Member
 
Join Date: August 24, 2001
Location: LC, Ca
Posts: 1,917
During WWII, American troops were trained to clean their rifles 3 days in a row after shooting to prevent corrosion. They used a solvent that was formulated to work on salts from the primer mix.
DnPRK is online now  
Old October 14, 2012, 12:46 PM   #6
coyota1
Senior Member
 
Join Date: April 6, 2008
Location: West Michigan
Posts: 663
Wouldn't cleaning and oiling prevent the potassium salts from allowing the moisture to attack the bore? I would think so.
coyota1 is offline  
Old October 14, 2012, 01:54 PM   #7
tobnpr
Senior Member
 
Join Date: August 1, 2010
Location: Tampa Bay
Posts: 4,556
Powder fouling left in the barrel is not an issue just as it wouldn't be with any other rifle.

Plain water (preferably hot) will dissolve the corrosive primer salt. Some guys use Windex, not really necessary IMO.

No way you did any severe damage to the barrel in a week's time, but you need to dissolve the salts completely, clean and then lightly oil the bore before you put it up.

Do a search, many discussions on this. Never a consensus (window cleaner, water, Hoppes #9) just like barrel break-in and "normal" barrel cleaning.

Me, I take a vial of Windex/water to the range and pour some down the breech after shooting, and then hot water down the bore followed by cleaning and an oiled patch when I get home when shooting corrosive ammo.

And.. don't forget about the boltface...
tobnpr is offline  
Old October 14, 2012, 02:09 PM   #8
tahunua001
Senior Member
 
Join Date: July 21, 2011
Location: Idaho
Posts: 7,839
quick answer is your gun is fine. I shoot surplus out of my mosin nagants regularly and only clean them every few weeks, I have no rust in my rifles, the rust takes a while to form, one week especially when it was already cleaned out fairly well is not enough to rust a barrel to the point that it's unsafe to shoot. maybe if you fired those 20 rounds and left it in a dank basement for a year it might but not after a week with a field cleaning applied.
__________________
ignore my complete lack of capitalization. I still have no problem correcting your grammar.
I never said half the stuff people said I did-Albert Einstein
You can't believe everything you read on the internet-Benjamin Franklin
tahunua001 is offline  
Old October 14, 2012, 08:14 PM   #9
kilotanker22
Senior Member
 
Join Date: October 14, 2012
Location: North Central, PA
Posts: 2,117
I think you are alright these things take time. Also for future reference you can squire 7.62 x 54 r ammo that is non corrosive for very cheap. By the way that is one h*%l of a deer cartridge.
kilotanker22 is offline  
Old October 14, 2012, 08:47 PM   #10
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 18,486
Quote:
Wouldn't cleaning and oiling prevent the potassium salts from allowing the moisture to attack the bore? I would think so.
No.
The report that identified the cause of barrel corrosion, after years of off the wall theories about "acid gases" from smokeless powder "in the pores of the steel" was titled "Corrosion Under Oil Films."

Corrosive primers contain potassium chlorate. This "burns" to leave potassium chloride, which is somewhat more reactive than sodium chloride = table salt.
I worked in R&D on fertilizers which use a lot of potassium chloride as a cheap source of potash plant nutrient. We were constantly on guard against corrosion whereever we could not use stainless steel. All it takes is water. it doesn't have to be hot, it doesn't have to be soapy, it doesn't have to have secret ingredients. Look how easily salt dissolves in water. That is what you are doing, dissolving and washing out salts. There is about 50 milligrams (.77 grain) of priming compound in a typical primer, not all of that potassium chlorate. It doesn't take a lot to get it out.
Wash, dry and oil.

WW II era GI bore cleaner contained soluble oil and water. Water to dissolve the potassium chloride, oil to protect the bare steel.
Jim Watson is online now  
Old October 14, 2012, 08:58 PM   #11
Amsdorf
Junior member
 
Join Date: July 24, 2011
Location: Saint Louis, Missouri
Posts: 849
"you can squire 7.62 x 54 r ammo that is non corrosive for very cheap"

And where would one obtain this "cheap" non-corrosive 7.62 x 54R ammo?
Amsdorf is offline  
Old October 14, 2012, 09:05 PM   #12
MrGoodwrench
Member
 
Join Date: September 27, 2012
Location: Northern Missouri
Posts: 22
I have the same question as above. I sure would like to find some non corrosive stuff. And brass cased to boot if possible?
MrGoodwrench is offline  
Old October 14, 2012, 09:11 PM   #13
the rifleer
Senior Member
 
Join Date: March 5, 2008
Location: Sunny California
Posts: 1,281
There is no flippin way you damaged the barrel in just over a weeks time, especially if you cleaned it last week. Did a little bit of rust form somewhere? maybe. Did you destroy your rifle? no way. Just clean it and it's fine.

In a weeks time with no cleaning whatsoever I would expect some mild surface rust at the most.
__________________
There is no such thing as a stupid question, only stupid people.
the rifleer is offline  
Old October 15, 2012, 08:42 AM   #14
jrothWA
Senior Member
 
Join Date: November 11, 2006
Posts: 2,519
Use HOT soapy water for..

cleaning the barrel and action and HOTTER water for flushing and drying from retained heat.
Then use standard solvent and oil for finishing.

Or locate and next gunshow old GI bore cleaner from WWII and use it.
jrothWA is offline  
Old October 15, 2012, 08:55 AM   #15
coyota1
Senior Member
 
Join Date: April 6, 2008
Location: West Michigan
Posts: 663
An old trick I use when cleaning black powder guns is to mix some soluble oil with hot water when you clean. The hot water evaporates fast, and the dash of soluble oil leaves a nice thin film of oil on the bare mettle surfaces.
coyota1 is offline  
Old October 15, 2012, 12:10 PM   #16
kilotanker22
Senior Member
 
Join Date: October 14, 2012
Location: North Central, PA
Posts: 2,117
My local shop has wolf ammo. Given it is Russian but the box says non corrossive. About 8 bucks a box.
kilotanker22 is offline  
Old October 15, 2012, 12:17 PM   #17
coyota1
Senior Member
 
Join Date: April 6, 2008
Location: West Michigan
Posts: 663
I used to shoot wolf in my SKS with out a problem.
coyota1 is offline  
Old October 15, 2012, 05:01 PM   #18
tobnpr
Senior Member
 
Join Date: August 1, 2010
Location: Tampa Bay
Posts: 4,556
Quote:
I sure would like to find some non corrosive stuff
Not as cheap as surplus (nothing is) but is made by Novosibirsk:

http://www.aimsurplus.com/product.as...Box&groupid=40
tobnpr is offline  
Old October 16, 2012, 03:19 PM   #19
Erno86
Senior Member
 
Join Date: September 22, 2012
Location: Marriottsville, Maryland
Posts: 1,738
You can never get a barrel totally clean...or you would be cleaning forever.
Before I use copper remover: I use cotton flannel patches soaked with Simple Green solution --- or a solution of --- 1/3 Simple Green, 1/3 hydrogen peroxide, 1/3 rubbing alcohol.

For some of my muzzleloaders, or breaking in a barrel, I use hot soapy Simple Green, and hot boiling water --- poured down the barrel --- so as too open up the pores in the metal, followed by cotton patches; and a oily patch.
Erno86 is offline  
Old October 16, 2012, 03:39 PM   #20
DE Shooter
Senior Member
 
Join Date: January 20, 2009
Posts: 215
I took several M91s to the range. Shot them with the spam can Russian milsurp stuff I always use. Got home, cleaned them as usual...hotwater down barrel and over bolt assembly, then normal cleaning with Hoppes & light Rem Oil finish. About two weeks later, I goth them out again, was going to sell one or a couple. Pulled the bolts out and checked the bores...LO & BEHOLD ! I had missed cleaning one.... the barrel was full of fuzz. Ran a wet patch thru and it came out covered with rust. So, I cleaned as mentioned above and the bore came out looking as good as before...not bad for a near 100 year old, multi-war rifle. I have since shot it and it still groups pretty good, 3-4" MOA. The rifling isn't shiny or sharp....but I don't see any pitting, which is what I would call heavy rust damage. I have seen some old M91s that were area-pitted to the point where the rifling could barely be seen. Your rifle should be fine.
DE Shooter is offline  
Old October 16, 2012, 05:49 PM   #21
warbirdlover
Senior Member
 
Join Date: December 13, 2009
Location: central Wisconsin
Posts: 2,324
I think you're fine. You cleaned it.
warbirdlover is offline  
Old October 17, 2012, 02:50 AM   #22
Bamashooter
Senior Member
 
Join Date: March 12, 2010
Posts: 1,860
Post #7 nailed it. Your rifle is fine. Just a little different cleaning procedure when corrosive ammo is involved. Enjoy your mosin nagant. They are very cool rifles. I have three.
Bamashooter is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:38 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.13629 seconds with 10 queries