July 16, 2011, 10:36 AM | #1 |
Senior Member
Join Date: December 26, 2004
Location: Louisville KY
Posts: 13,805
|
Cleaning my AR
I have an embarrassing question about my M&P Sport.
Very little of this gun sees any carbon buildup, except for the 'Hershey's kiss' shaped part of the bolt, and the chamber it sits in. Is there a specialized brush to scrape the junk out of the chamber? What is the best way to get it off the curved piece on the right? It's very hard, almost like concrete. |
July 16, 2011, 11:00 AM | #2 |
Senior Member
Join Date: March 17, 2008
Location: Indiana
Posts: 2,857
|
When I get to cleaning that grimy little nub (about every 600rds or when the mood strikes me), I stand up the bolt in a shotglass with some CLP or other mild cleaning agent in it. Wait 24hrs+, then go at it with one of those gun-toothbrush type deals. I don't worry about getting it spotless, just cleaning off the majority of BBQ-grill deposits that tend to build up over time.
The oriface in the bolt carrier I usually clean with Hoppe's #9 and big patches. Sometimes it gets a brushing with a big-bore brass barrel brush if it's really crusty.
__________________
"A human being is primarily a bag for putting food into; the other functions and faculties may be more godlike, but in point of time they come afterwards." -George Orwell |
July 16, 2011, 06:36 PM | #3 |
Senior Member
Join Date: May 4, 2001
Posts: 7,477
|
There are several ways to clean the carbon off the bolt "tail" and the inside of the bolt carrier.
The fastest ways are: Buy special carbon removal tools. These cut or scrape the carbon out: http://www.brownells.com/.aspx/pid=1...CARBON_SCRAPER http://www.brownells.com/.aspx/pid=3...RADIUS_SCRAPER http://www.brownells.com/.aspx/pid=3...N_REMOVAL_TOOL (CRT-15 for the AR-15). http://www.brownells.com/.aspx/pid=3...M16_CAT_M4TOOL http://www.brownells.com/.aspx/pid=1...CARBON_SCRAPER (Number 016 for the AR-15) The second method is to buy a big jar of Slip 2000 Carbon Cutter. This is a safe chemical that dissolves the carbon by just soaking the part. http://www.brownells.com/.aspx/pid=2..._2000_SOLVENTS If you don't have time to fool around with soaking for hours in various solvents like bore solvents and scrubbing with bore brushes, and you want it cleaned fast and without harming the parts, these are the best methods. |
July 17, 2011, 03:46 PM | #4 |
Senior Member
Join Date: March 29, 2009
Location: NW Ohio
Posts: 569
|
I have actually had really good luck with using a razor utility knife scraping off the carbon. Scrape off as much as you possibly can by hand before using any chemicals that way the chemicals really have a chance to dig in and do their thing.
I imagine ultrasonic cleaners are probably good at removing the carbon as well, so if you have one maybe poke around and see how well they work on the bolts. |
July 17, 2011, 06:04 PM | #5 |
Senior Member
Join Date: May 4, 2001
Posts: 7,477
|
Ultrasonic cleaners don't do very well on this type of hard carbon deposits.
Unless you use a solvent that in itself attacks the carbon ultrasonics don't really help much. Never use a steel scraper to remove carbon unless it's a tool specifically designed for that purpose. If you scratch the metal with a steel blade, the carbon will adhere to the scratched part even worse and faster. |
Thread Tools | Search this Thread |
|
|