The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools Search this Thread
Old March 14, 2013, 10:58 PM   #1
Palmetto-Pride
Senior Member
 
Join Date: May 31, 2009
Location: Charleston, SC
Posts: 2,071
Loaded my first rifle rounds.

Well I finally loaded my first 308WIN rifle rounds.

My load............................

Case: 308WIN Hornady Match
Primer: Federal NO. 210 Large Rifle (Not the 210M, but its all I could find)
Bullet: 168 GR. Sierra MK HPBT (First choice was AMAX , but beggars can be choosy)
Powder: Benchmark (Not my first choice, but once again had to settle)
Charge: 42.0 GRS
C.O.L: 2.800

I am nervous and excited at the same time......

I measured, measured, and remeasured the powder charge about 20 times before I proceeded to fill all the cases.

Going to the range tomorrow hope I come back with all my fingers....
__________________
“The problem with socialism is that you eventually run out of other people's money.”

-Margaret Thatcher-
Palmetto-Pride is offline  
Old March 14, 2013, 11:13 PM   #2
Fire_Moose
Senior Member
 
Join Date: January 16, 2013
Posts: 211
Re: Loaded my first rifle rounds.

Didja check each.case for power before setting the bullet on top?

Good on ya, good luck. That first round is nerve racking.
Fire_Moose is offline  
Old March 15, 2013, 12:31 AM   #3
Palmetto-Pride
Senior Member
 
Join Date: May 31, 2009
Location: Charleston, SC
Posts: 2,071
Yea what I did was take each case and zero it out on the scale dropped the powder checked to make sure each one was getting 42.00 grs none got below 41.80 and the ones that went slightly over 42.00 I dumped the powder and redid them. I have never reloaded before, but I cant see where .20 of a grain of powder will make a huge difference in FPS. I tried to trickle them up, but keep going a little over so for now I can live with it until I see how these shoot.
__________________
“The problem with socialism is that you eventually run out of other people's money.”

-Margaret Thatcher-
Palmetto-Pride is offline  
Old March 15, 2013, 03:33 AM   #4
Fire_Moose
Senior Member
 
Join Date: January 16, 2013
Posts: 211
Re: Loaded my first rifle rounds.

That's a round n about way to do it...you have a pan for the scale?
Fire_Moose is offline  
Old March 15, 2013, 05:34 AM   #5
hooligan1
Senior Member
 
Join Date: July 18, 2010
Location: Independence Missouri
Posts: 4,582
Have you tested this load?
__________________
Keep your Axe sharp and your powder dry.
hooligan1 is offline  
Old March 15, 2013, 05:39 AM   #6
sourdough44
Senior Member
 
Join Date: October 17, 2007
Location: WI
Posts: 621
The Hodgdon site shows a charge range of 38-42 grns of Benchmark for a 168 grn bullet. Other sources may vary, but why the need to go right to max charge weights with your 1st loads? Not ripping on you but the target won't care, your gun, brass & a few other things may thank you for lower charges. Just asking.


OBTW, my Sierra manual tops out at 41.4 with that bullet. Yes, the kids say I drive like a Grandpa at times too.
sourdough44 is offline  
Old March 15, 2013, 05:56 AM   #7
Dave P
Senior Member
 
Join Date: August 16, 1999
Location: North Florida
Posts: 1,346
"Yea what I did was take each case and zero it out on the scale dropped the powder checked to make sure each one was getting 42.00 grs none got below 41.80 and the ones that went slightly over 42.00 I dumped the powder and redid them."

Whew - that wears me out just reading it! I think you are over-doing it.

If 42 grains is a safe load, then +- .5 grains will be fine too. Maybe weigh every tenth one if you have to, and eyeball the rest with a flashlight.

I only weight the first one (for run of the mill loads).
__________________
I think this country is screwed.
Dave P is offline  
Old March 15, 2013, 11:18 PM   #8
Palmetto-Pride
Senior Member
 
Join Date: May 31, 2009
Location: Charleston, SC
Posts: 2,071
Quote:
The Hodgdon site shows a charge range of 38-42 grns of Benchmark for a 168 grn bullet. Other sources may vary, but why the need to go right to max charge weights with your 1st loads?
I was wanting to duplicate the federal factory ammo with this same bullet that pushes this bullet at 2650. I have used this same ammo in my rifle and it is very accurate. Hoping to duplicate or do better with these hand loads........and I cant lie if you tell me I can go 100 MPH I would try and go 101 MPH that just the way I am
__________________
“The problem with socialism is that you eventually run out of other people's money.”

-Margaret Thatcher-
Palmetto-Pride is offline  
Old March 17, 2013, 02:02 PM   #9
Palmetto-Pride
Senior Member
 
Join Date: May 31, 2009
Location: Charleston, SC
Posts: 2,071
So I shot four five shot groups yesterday and I didn't do too bad I would get 3-4 to touch each other and then have one or two touch away from the other three, over all not bad, but I am gong to "work it down a little" anyway no blown up gun...lol
__________________
“The problem with socialism is that you eventually run out of other people's money.”

-Margaret Thatcher-
Palmetto-Pride is offline  
Old March 17, 2013, 04:32 PM   #10
Bart B.
Senior Member
 
Join Date: February 15, 2009
Posts: 8,927
Palmetto, your 2/10ths grain spread in charge weight's plenty good enough.

.308 Win. ammo with 3/10ths grain spread in charge weight's shot sub 3-inch 30-shot test groups at 600 yards.

There's many things more important that that much charge spread.
Bart B. is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:54 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.03989 seconds with 10 queries