|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
November 1, 2011, 11:21 PM | #1 |
Junior Member
Join Date: November 1, 2011
Posts: 3
|
Ruger Hawkeye Accuracy Improvements
What is the best way to improve Accuracy for these guns. I just bought a new one in 7mm-08. With factory ammo I get around a 3" group at 100 yards. With a 175grain hand load I can get a 1" group at 100yards. This is fine for where I hunt in the southeast, but I would like to improve the overall accuracy of the gun.
I have heard that some rugers behave badly when free floated. I also have synthetic stock. Should I bet the action? Any suggestions would be appreciated thanks |
November 2, 2011, 04:34 AM | #2 | |
Senior Member
Join Date: November 26, 2006
Posts: 1,161
|
Quote:
|
|
November 2, 2011, 05:05 AM | #3 |
Senior Member
Join Date: June 15, 2008
Location: Georgia
Posts: 10,805
|
Rugers are more senstive to action screw torque than most. Most guys report better accuracy by loosenig all screws. First tighten the front screw as tight as you can possibly get it. Tighten the rear screw almost as tight. The middle screw should be snugged up just tight enough so as not to fall out. I've read of some improvement after this. Worth a try.
I'd try some different bullet weights and different factory loads. Also, if it is a new rifle it will shoot better after it's had had several boxes of ammo shot through it. Don't give up too soon. Rugers aren't known as tack drivers. I've only seen 1 that would consistently shoot groups of around 1/2", but I've also never seen one that was worse than a 1.5" gun either. |
November 2, 2011, 06:04 AM | #4 |
Junior member
Join Date: February 11, 2005
Posts: 822
|
things that help other rifles like a trigger job and glass bedding and floating help rugers too. Best bet though is to keep trying differnt bullet, powder and primer combos.
|
November 2, 2011, 06:25 AM | #5 |
Member
Join Date: September 21, 2011
Location: Idaho
Posts: 92
|
Tighten your stock as seen on this video
http://www.youtube.com/watch?v=8KGAYS91BDk When I first purchased mine it had 'play' in the stock. I just took the whole rifle apart and tightened everything. The new Hawkeye is free floated with some pressure system ( don't ask me, this is what ruger told me ) My Hawkeye will place three shots inside 1" at 100. Not bad for a .358 winchester |
November 2, 2011, 09:46 AM | #6 |
Senior Member
Join Date: December 13, 2009
Location: central Wisconsin
Posts: 2,324
|
I'd try these guys suggestions. My Ruger M77 MkII all-weather .300 Win Mag is always under an inch at 100 yards. Usually cloverleaf groups. It does that with any brand factory ammo I feed it and any weight factory ammo. It's maybe one in a million. Never will sell it.
|
November 2, 2011, 10:05 AM | #7 |
Senior Member
Join Date: March 30, 2011
Location: Milwaukkee, WI
Posts: 152
|
jmr40,
I am confused by your instructions!!! You say most Ruger shoot best with the screws loose, but then you say to tighten the front and back screw tight and just snug on the middle screw. Bob |
November 2, 2011, 11:41 AM | #8 |
Senior Member
Join Date: January 6, 2011
Location: Thornton, Texas
Posts: 3,998
|
I put a new stock on mine (Hogue, with aluminum bedding channel), had a lighter trigger spring installed ($10), and found just the handload that it liked. It's not a 7-08, so my load data won't help you. The rifle shoots wonderfully now. I'll admit that I don't think the stock was the problem, since I put that synthetic stock (with the barrel channel opened up) on a Ruger short action 260 I have, and the 260 shoots great. The Hogue stock now on the Hawkeye is a bit heavier than I'd prefer, but the gun shoots so good now that I'm not changing anything. One other thing to mention is that it appeared to me that the barrel needed to be 'seasoned' or 'shot in' or whatever you want to call it, and that took a couple of hundred rounds. I guess I had to lay down some copper. The experts on the forum may have more and better info on that.
As for the action screws, I did what the Ruger website suggested, which is tightened (after first being loosened) just as jmr40 suggests. |
November 2, 2011, 01:59 PM | #9 | |
Senior Member
Join Date: June 15, 2008
Location: Georgia
Posts: 10,805
|
Quote:
The angled action screw Ruger uses can work, but it works different. By tightening the front screw 1st, it pulls the gun down into the stock snugly. Then you tighten the others. If you don't loosen the others fist, you will just be getting the screw tight, but with the other screws already tightened they will not allow the action to move down and back into the stock properly. |
|
July 10, 2013, 12:20 AM | #10 |
Member
Join Date: May 16, 2013
Posts: 29
|
JMR40
So for a new Hawkeye would you suggest loosening then tightening the action screws even before being shot?... I am just curious because I am looking to buy a Hawkeye sporter in .308. |
July 10, 2013, 12:56 AM | #11 |
Senior Member
Join Date: January 22, 2012
Posts: 304
|
I'll tell you something that might **** off a few 7mm-08 fans here but the 7mm-08 is a finicky cartridge despite what the books say, took me seven months to get mine dialed in right. I don't load 175gr the heaviest thing I load is 160gr Deep Curls and Game Kings but they do really well with H380 powder (consult your Lyman #49 for load data) The only two powders that shoot worth a darn for me are Big Game and H380 it took me a long time to figure that out. H414, RL19, and IMR4350 would hardly stay on the paper at 100 yards. So long story short it might not be the rifle, I know several experienced handloaders who had trouble with their 08s.
|
July 10, 2013, 07:28 PM | #12 |
Senior Member
Join Date: January 27, 2010
Location: AR
Posts: 1,401
|
knifeguy posted
What is the best way to improve Accuracy for these guns. I just bought a new one in 7mm-08. With factory ammo I get around a 3" group at 100 yards. With a 175grain hand load I can get a 1" group at 100yards. This is fine for where I hunt in the southeast, but I would like to improve the overall accuracy of the gun. I have heard that some rugers behave badly when free floated. I also have synthetic stock. Should I bet the action? Any suggestions would be appreciated thanks --------------------------------------------------------------- I think you have the answer -- reloading. In all my days of shooting, I have seen my share of bolt guns that would shoot 3-6 inch groups with factory ammo. Conversely, I do realize there are those that will shoot sub MOA groups with the factory fodder. Years ago I acquired a Rem 700 in 243 that no matter what factory ammo I used, best I could get was a 4" group. With Sierra bullets, my first reloads gave me a 3/4" group and saved the rifle from being sold or traded. |
Tags |
ruger |
Thread Tools | Search this Thread |
|
|