|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
November 28, 2005, 10:39 AM | #1 |
Member
Join Date: October 25, 2005
Posts: 65
|
.444 marlin reload question
I am totaly new to reloading, (have no gear, haven't read any books YET new)
the main 3 calibers atm that i am looking to reload is .444marlin. 38 spl, 45lc i have not found any bullets on any web site i have been too that say .444 i have seen several .44 as well as plenty for the 38 & 35 the 38 uses a.357 and 45 a .451 bullet correct. what should i look for in diamiter on a bullet that will work for the .444 marlin? |
November 28, 2005, 11:22 AM | #2 | |
Senior Member
Join Date: October 15, 2004
Posts: 934
|
Quote:
If you try cast bullets, they absolutely must be oversized. The lead alloy is so soft that as long as the loaded cartridge will chamber freely, it's safe to shoot. The smallest even worth trying in the .38 is .358, .430 in the .444, and .452 in the .45. |
|
November 30, 2005, 04:54 PM | #3 |
Senior Member
Join Date: July 14, 2002
Location: Marilla, N.Y. (outside Buffalo N.Y.)
Posts: 113
|
If you use the 444 for hunting you have to make sure the bullet is contructed well enough to take the additional velocities in the rifle. A 44 mag bullet is the same diameter as the 444, but might not work well on a tough game animal.
__________________
The shortest distance between two politicians is through your wallet. Don N. |
November 30, 2005, 05:10 PM | #4 |
Senior Member
Join Date: November 13, 2004
Location: PacWest
Posts: 455
|
Buy a few manuals - Hornady, Nosler and such
As noted the .444 Marlin will take .44 pistol bullets and overdrive them to failure on game.
There are twist issues with the .444 which is sort of an express design (though not to be confused with a blackpowder express the intent was somewhat the same) so the longer heavier rifle bullets may well be unsatisfactory. Buy some manuals by the various major bullet manufacturers and start with their suggestions - or read the books at the store or better the library. |
November 30, 2005, 09:46 PM | #5 |
Member
Join Date: March 15, 2005
Posts: 77
|
If you are using an older .444 with the Micro-Groove rifling, you will need to stay below 300 grs. of bullet weight. The slow 1 in 38 twist rate will not properly stabilize the heavier and longer bullets. The newer .444s use a more conventional land and groove arrangement and have a faster twist rate that should stabilize most if not all .429/.430 bullets.
|
November 30, 2005, 11:01 PM | #6 |
Senior Member
Join Date: August 11, 2001
Location: Utah
Posts: 1,462
|
A good slug in the 444 marlin is the 265 grain hornady. It will handle the 444 marlins velocity. Why? Because it was designed FOR the marlin, not the 44 mag. VERY tough slug.
__________________
From my cold dead hands......... NRA certified rifle, pistol and shotgun instructor. Hunter education instructor |
December 1, 2005, 12:32 AM | #7 |
Member
Join Date: July 4, 2005
Location: Savannah, GA
Posts: 27
|
Ben Shepherd says it all reference the 265 Hornady
|
December 1, 2005, 10:35 PM | #8 |
Senior Member
Join Date: August 11, 2001
Location: Utah
Posts: 1,462
|
How do I know this, you ask? Easy- Says so in the hornady manual.
There, not so tough to figure out, eh? Good shooting, that's a fun caliber.
__________________
From my cold dead hands......... NRA certified rifle, pistol and shotgun instructor. Hunter education instructor |
December 29, 2005, 01:47 AM | #9 |
Member
Join Date: November 30, 2004
Location: kansas city area at the present, but Colorado and Wyoming have been home. Lived 2 years in the middle east.
Posts: 33
|
.444 Marlin
Been loading .444 Marlin for years. Have used 240, 265 and 300 grain bullets but the 265 Hornady have been the most accurate by far. Anything that big and that slow tears up a lot of meat what ever bullet is used. I figure accuracy helps in selecting what I want to dismember.
|
|
|