The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools Search this Thread
Old September 15, 2018, 02:05 AM   #1
mellow_c
Senior Member
 
Join Date: January 7, 2008
Location: Colorado
Posts: 1,739
J.C. Higgins model 103.18, need buttplate

Title pretty much says it all. I can't find one anywhere online. I'd like to if I could.

Otherwise I'd be happy to make one, or fit one from a different rifle to this rifle.

It's just a cheap old single shot that I'd like to freshen up.

The end plate needs to be at least 4 & 9/16th inches tall and about 1 & 9/16th inches wide. Screw holes are 3/4 inch bellow top of stock to center of top hole and 1 & 1/16th inches above bottom of stock to center of bottom hole. With 2 & 3/4 inches between center of two holes.

If anyone knows of anything that will fit, or of something that I can make fit, or an original replacement, I would greatly appreciate you letting me know!

Thanks.
mellow_c is offline  
Old September 15, 2018, 12:35 PM   #2
T. O'Heir
Senior Member
 
Join Date: February 13, 2002
Location: Canada
Posts: 10,135
The J.C. Higgins Model 103.18 is a Marlin M100 made from 1936 to 1941. Isn't listed on Gunparts 'Cross Reference' page.
However, Gunparts wants $15.20 for a repro.
https://www.gunpartscorp.com/products/432990F
__________________
Spelling and grammar count!
T. O'Heir is offline  
Old September 16, 2018, 02:30 PM   #3
mellow_c
Senior Member
 
Join Date: January 7, 2008
Location: Colorado
Posts: 1,739
Thanks for the info. Looks like Numrich is the only place selling them. I'm tempted to buy it, but $15.00 + $7ish for shipping to buy a buttplate to go on an $80 rifle... Well, I don't know.

Maybe I'll just go for it. Or possibly wait till I have $75 worth of other stuff I need to order from them so I can get free shipping.

Thanks again for the help locating just what I need!
mellow_c is offline  
Old September 17, 2018, 02:59 PM   #4
gwpercle
Senior Member
 
Join Date: November 30, 2012
Location: Baton Rouge, Louisiana
Posts: 744
When I needed a butt plate for a Western Auto single shot bolt action 410 shotgun....not a whole lot of parts available for these , let me tell you . I found a slab of walnut about 1/2 inch thick and carved one . Shaped it just like the original plastic one and cut a thin white spacer from a white plastic bottle to make a white line spacer...looked good and cost $0.00.
I even got fancy , cut some coarse/crude checkering in it ...Bubba at it again !
Gary
gwpercle is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:29 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05087 seconds with 9 queries