|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
August 29, 2009, 11:21 PM | #1 |
Senior Member
Join Date: September 6, 2008
Posts: 1,777
|
Lyman .44 pistol round ball size??
I have this .44 lyman pistol.. What size roundball do I need?? On the barrel it says .44 cal... I do not have a manual and I cannot find one other than the ones for the .50 and .54 cal models... Thanks
|
August 29, 2009, 11:41 PM | #2 |
Senior Member
Join Date: March 19, 2008
Location: High & Dry in Missouri Ozarks
Posts: 2,113
|
Generally, for patched round ball, you go with a ball ,010 smaller than bore diameter. In the case of a 44 single shot, you'd use a .430 roundball and .010 patch to start and adjust patch thickness and ball diameter combinations to dial it in for best accuracy. Fot my Pedersoli .54 Tryon rifle and Pedersoli .54 Kentucky I started with a .530 ball and .010 patch. After a few years of shooting and trying various combinations, I found that they both favor a .535 roundball with .005 lubed patch.
__________________
Fingers (Show Me MO smoke) McGee - AKA Man of Many Colts - Alter ego of Diabolical Ken; SASS Regulator 28564-L-TG; Rangemaster and stage writer extraordinaire; Frontiersman, Pistoleer, NRA Endowment Life, NMLRA, SAF, CCRKBA, STORM 327, SV115; Charter member, Central Ozarks Western Shooters Cynic: A blackguard whose faulty vision see things as they are, not as they should be. Ambrose Bierce |
August 30, 2009, 12:23 AM | #3 |
Senior Member
Join Date: March 15, 2005
Location: Central Connecticut
Posts: 3,166
|
Track of the Wolf has a selection of cast round balls:
http://www.trackofthewolf.com/(S(y5j...=25&styleID=58 The best ball & patch combination to use is based on the actual bore diameter and depth of the rifling. A .433 round ball and a .005 or .007 lubed patch could work. And a .429 round ball and .010 lubed patch could be just about right, but if it's too tight or lose than use a thinner or thicker patch. A .424 round ball and a .015 lubed patch is another option. And the next thicker patch size is .018 pillow ticking. The thicker the patch and larger the ball, the harder it will be to load. Always use a short ball starter. Last edited by arcticap; August 30, 2009 at 12:28 AM. |
August 30, 2009, 03:19 AM | #4 | |
Senior Member
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,188
|
Quote:
|
|
August 30, 2009, 05:27 AM | #5 |
Senior Member
Join Date: October 8, 2006
Location: Northern Michigan
Posts: 2,772
|
A short ball is what I play golf with, usually when putting. It always stops short of the hole.
|
August 30, 2009, 05:16 PM | #6 |
Senior Member
Join Date: March 15, 2005
Location: Central Connecticut
Posts: 3,166
|
It's what results when a short starter goes out on a date with a ball starter, then a while later out pops a short ball starter!
It gets even more confusing when one of them is long starter! Last edited by arcticap; August 30, 2009 at 05:23 PM. |
September 3, 2009, 09:22 PM | #7 |
Senior Member
Join Date: October 1, 2004
Location: Remote Utah desert
Posts: 224
|
The long starters are generally only available in African Ironwood.
Occasonally you see one in American White Pine but it's not as common.
__________________
"And lo, did I see an ugly cat. Smoke. Brimstone. Holes in parchment. And this ugly cat was much amused." --- The Prophesies of Gatodamus (1503 - 1566) |
September 5, 2009, 09:42 PM | #8 |
Senior Member
Join Date: December 14, 2004
Location: Northern Indiana
Posts: 6,117
|
Always use a short ball starter.
OK if no one is going to explain what that means to the novas black powder shooter I will. A ball starter is a round wooden ball about 2 1/2 inches in diameter. A good one will have two brass rods sticking out of the ball. The shorter one which is 1/2 inch long is used to start the patched ball just deep enough to cut the patch if you’re not using pre-cut patches. The other rod is normaly 4 to 6 inches and is used to get the bullet and patch started down the barrel deeper and it saves wear on your wooden reamer. They just make loading a muzzle loader much easier. |
September 6, 2009, 12:39 PM | #9 |
Member
Join Date: February 27, 2008
Posts: 41
|
I had the rifle version of that pistol several years ago and I had to use a .429 sized ball and really thin patch.
|
January 9, 2010, 05:32 PM | #10 |
Junior Member
Join Date: January 9, 2010
Posts: 1
|
Lyman 44 cal
I have a weapon that looks exactly like your picture. I received it about 25 years ago. There is a USA quarter embeded in the butt. What can you tell me about thes weapon? How old is it? The barrel appears to be about 10" and is chrome.
Any help would be appreciated. |
Thread Tools | Search this Thread |
|
|