|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
January 5, 2019, 04:57 PM | #1 |
Senior Member
Join Date: September 2, 2010
Location: Plainview , Long Island NY
Posts: 3,863
|
Weak 8 round magazine spring.
Using this magazine for practice only , I only load 5 in the magazine anyway so I was thinking if I dropped a block 1/2" high at the base of the mag wouldn't that tighten the spring to fire the fifth round 100% until new springs arrixe ?
|
January 5, 2019, 05:38 PM | #2 |
Senior Member
Join Date: March 1, 2000
Location: Boise, ID
Posts: 8,518
|
Some people put empty cases under the spring.
You could also load eight and shoot five.
__________________
Runs off at the mouth about anything 1911 related on this site and half the time is flat out wrong. |
January 5, 2019, 06:31 PM | #3 |
Senior Member
Join Date: March 20, 2014
Location: Kinda near Phoenix, AZ
Posts: 1,254
|
Which mag spring? 1911? FYI, its about $7-$8 for a single 1911 mag spring. No need to jerry rig a fix if the spring is that cheap.
|
January 5, 2019, 07:31 PM | #4 |
Senior Member
Join Date: September 2, 2010
Location: Plainview , Long Island NY
Posts: 3,863
|
Thanks guys for answering so fast springs are on order but just in a pinch by blocking up the mag bottom to increase tension for the 5th round not for a permanent fix. Will give it a try if new springs don't arrive in time. Thanks Again.
Chris |
January 6, 2019, 02:41 PM | #5 |
Senior Member
Join Date: February 12, 2000
Posts: 210
|
Just pull the spring out and stretch it and put it back in.Repeat as nessasary.
|
January 6, 2019, 03:05 PM | #6 |
Senior Member
Join Date: April 7, 2006
Posts: 10,985
|
When wire springs get weak, they are developing micro cracks along their length. They will break soon after.
|
January 6, 2019, 03:29 PM | #7 |
Member
Join Date: January 3, 2019
Posts: 69
|
If it is a 1911 .45, I use Chip McCormick, and it takes a lot to weaken those springs. I have had one loaded for 5 years, and I don't think it has affected the spring.
And I think Mec-Gar is about the same. I would buy an extra mag myself. |
January 6, 2019, 03:53 PM | #8 |
Senior Member
Join Date: March 1, 2000
Location: Boise, ID
Posts: 8,518
|
Leaving them loaded doesn't wear them, using them does.
I left a Wilson 8-rounder loaded for 20 years, and it worked. I wore-out a Shooting Star 8-rounder, two of them, in a year of weekly use.
__________________
Runs off at the mouth about anything 1911 related on this site and half the time is flat out wrong. |
January 7, 2019, 12:51 AM | #9 |
Senior Member
Join Date: April 7, 2006
Posts: 10,985
|
I have pistols that have been loaded for 40+ years that work just fine.
|
January 7, 2019, 09:30 AM | #10 |
Senior Member
Join Date: September 2, 2010
Location: Plainview , Long Island NY
Posts: 3,863
|
Use for sure weakens mag. springs , carry mags will work forever it seems just remove the lint.
|
January 7, 2019, 11:35 AM | #11 | |
Senior Member
Join Date: February 15, 1999
Location: Winston-Salem, NC USA
Posts: 6,348
|
Quote:
Stretching the spring, as suggested, just speeds up the micro-fracturing process. Metal doesn't heal or get stronger with rest, and stretching the spring just adds additional stress to the metal that is already weakening. When you stretch a coil spring, you notice an improvement the first time you use it, than you'll see an even faster decline in the spring's functional abilities.Magazine springs can be replaced. You should see if sources like Wolff carry a spring for your magazine. (If they don't have one, you might be able to find an 8-round magazine that is dimensionally similar, and it's possible that spring -- which they might carry -- will work in your mag. Anything else you do will work only temporarily -- and the springs will continue to degrade, and in some cases do it more rapidly. . Last edited by Walt Sherrill; January 7, 2019 at 11:59 AM. |
|
January 7, 2019, 12:38 PM | #12 |
Senior Member
Join Date: December 5, 2010
Posts: 196
|
I have used these Tripp springs to replace Checkmate OEM springs without having to also replace the follower http://www.trippresearchinc.com/ms-14c-042/. They are the strongest springs I've come across and have run flawlessly.
I have used Tripp's Super 7 upgrade hits to replace the guts (spring and follower) of CMC and Checkmate magazines http://www.trippresearchinc.com/super-7-upgrade-kit/. These have also run 100%. |
January 7, 2019, 01:54 PM | #13 | |
Senior Member
Join Date: November 20, 2008
Posts: 11,132
|
Quote:
|
|
January 7, 2019, 02:19 PM | #14 | |
Senior Member
Join Date: February 15, 1999
Location: Winston-Salem, NC USA
Posts: 6,348
|
Quote:
Working (cycling) isn't the only thing that can weaken a coil spring. Hi-cap mag springs, depending on their design and how they're used, can also weaken from being left loaded for long periods. Note: rotating carry mags doesn't prolong magazine spring life -- it just shifts the work to a different set of magazines. And if the unused mags are stored loaded, it possible that you've done NOTHING to delay wear. (It depends on the mag design and how the springs are used.) While working a spring can cause wear, the only part of the work cycle that causes significant wear is when the spring is fully compressed the the spring is ALSO near its design limit (also called it's elastic limit). That isn't the case with many magazine designs. But it does happen with many hi-cap mags.That's why Wolff Springs (in the FAQ section of their site) generally recommends downloading high-cap mags a round or two for long-term storage. (They don't suggest that for the mags IN a carry gun.) The same kind of spring degradation can occur with recoil springs, if a slide is left locked back for extended periods. When a coil spring is bent too far for too long (at or near it's "design limits", the metal can begin to fracture when held in that position, and continued use at that compression level will cause the damage to slowly cascade, as more and more metal slowly breaks (and the remaining metal must do the same work). It's bending (compressing) the coil spring's metal that damages the metal, not bending and releasing it. (The releasing part is good and NOT work.) The farther the metal is bent the more likely it is to be damaged. Metal fatigue is one way of describing it, but that's an oversimplification. When coil springs in guns fail they will generally degrade (SOFTEN) and quit working properly before they break; they're replaced before they can break. Coil springs in car suspensions, on the other hand, don't keep a car from being driven, so they might eventually continue to be used until they break (from fatigue);l then they're replaced. On the other hand, if, when a mag is fully loaded, the spring isn't near or at its "design" limit, that spring may outlive the gun in which it's used. 7-round 1911 magazines are like that -- they seems to almost never wear out. And many standard (non high-cap) mag springs in full-size guns also tend to have long service lives. Last edited by Walt Sherrill; January 7, 2019 at 03:04 PM. |
|
January 7, 2019, 02:31 PM | #15 | |
Senior Member
Join Date: October 28, 2006
Location: South Central Michigan...near
Posts: 6,501
|
Quote:
|
|
January 7, 2019, 02:46 PM | #16 |
Senior Member
Join Date: April 7, 2006
Posts: 10,985
|
I have no link.
I can tell you that I have replaced thousands of springs with springs that I hand make. Most are leaf springs, some are coils. |
January 7, 2019, 03:46 PM | #17 | |
Senior Member
Join Date: February 15, 1999
Location: Winston-Salem, NC USA
Posts: 6,348
|
Quote:
Here's a good place to start. https://thefiringline.com/forums/sho...ne+spring+life There have been MANY such discussions on this forum, including input from aeronautical engineers, technicians who work with spring specifications, and metallurgists. One of the more interesting discussions starts in the link above, provided by one of the staffers here on TFL JohnKsa. John is also an engineer, and a long-time air gun (spring powered) enthusiast, as well as someone familiar with handguns. Another member who has provided great technical citations is Danez71, who worked with springs at different times on the job. Do a search on "magazine springs", "spring life" for a number of discussions. Most of them have links to technical or scientific sites, but the older ones have "cold" links. Wikipedia is cited with good technical explanations of the concepts and terms being discussed. Here are some of the definitions, and I may be able to find others: http://en.wikipedia.org/wiki/Elasticity_(physics) http://en.wikipedia.org/wiki/Plasticity_(physics) http://en.wikipedia.org/wiki/Viscoelasticity http://en.wikipedia.org/wiki/Creep_(deformation) |
|
January 7, 2019, 10:14 PM | #18 |
Senior Member
Join Date: October 28, 2006
Location: South Central Michigan...near
Posts: 6,501
|
My question is about micro-cracks causing magazine spring weakening...not about metallurgical definitions. I would have thought it would have been something more exotic, like some of the Martensitic space lattice reverting back to a Ferritic space lattice due to the physical working of the steel during cycling.
|
January 8, 2019, 03:17 PM | #19 |
Senior Member
Join Date: February 15, 1999
Location: Winston-Salem, NC USA
Posts: 6,348
|
This is a topic that has been discussed by various folks, over the years.
Here's a link to a simple explanation of the various ways that metal responds to stress -- from shattering, to deforming, to bending; but the metal will inevitably break if the source of the stress is not removed. The last part of the linked article below is the appropriate part, but I'll post that section, below. Reading the whole article, which isn't a lot, is worth the effort. (Note: in the first paragraph cited below, their use of "yield point" is the same as "elastic limit." Rather than call the part of the metal structure affected by stress a micro-fracture this article calls it a FAULT, but it's phenomenon. i.e., a change in how the material holds itself together at the molecular level. Keep in mind that springs are considered a DUCTILE metal. https://www.thebalance.com/metal-str...lained-2340022 From the link: Metal Fatigue Resulting from Metal Strain Last edited by Walt Sherrill; January 8, 2019 at 10:25 PM. |
January 9, 2019, 09:19 AM | #20 | |
Senior Member
Join Date: October 28, 2006
Location: South Central Michigan...near
Posts: 6,501
|
Quote:
|
|
January 9, 2019, 07:08 PM | #21 | |
Senior Member
Join Date: February 15, 1999
Location: Winston-Salem, NC USA
Posts: 6,348
|
Quote:
Some metals (such as stainless steel and many other alloys) yield under stress. It allows them to bend, or deform, without breaking. Other metals, such as cast iron, fracture and break quickly under stress. Even stainless steel, however, finally weakens and breaks under enough stress.That same article, when addressing BRITTLE STEELS, says: Some metals are intrinsically brittle, which means they are particularly liable to fracture. Brittle metals include medium and high carbon steels. Unlike ductile materials, these metals do not have a well-defined yield point. Instead, when they reach a certain stress level, they break.Wikipedia says the following with regard to spring steel: These steels are generally low-alloy manganese, medium-carbon steel or high-carbon steel with a very high yield strength. This allows objects made of spring steel to return to their original shape despite significant deflection or twisting.Coil spring do a lot of bending and twisting, so while some springs might have a relatively high carbon steel content, stainless steel is an alloy mixed with other metals that offset the high carbon . Stainless steel is apparently used in gun springs because of its greater rust/corrosion resistance -- as a rusting spring loses it physical integrity more quickly than one that doesn't rust. Stainless Steel seems to include a number of components, tweaked to address the specific needs of the task at hand:
http://www.whitesounddefense.com/pag...Materials.html In general, the greatest danger to guns springs is corrosion. Springs are typically the thinnest metal in the firearm and as such they are extremely vulnerable to catastrophic failure from corrosion. This is why when design parameters allow for it, the best choice for firearm springs that are expected to function in the field is a stainless steel.If you have other sources, particularly ones that suggest a different interpretation, please share them with us. Last edited by Walt Sherrill; January 9, 2019 at 07:57 PM. |
|
January 9, 2019, 07:59 PM | #22 | |
Senior Member
Join Date: October 28, 2006
Location: South Central Michigan...near
Posts: 6,501
|
Quote:
These steels are generally low-alloy manganese, medium-carbon steel or high-carbon steel..." As for making springs out of Stainless Steels, that may be the practice now, but when John Browning invented his 1911 (and its spring-loaded magazine), it was still two years before the first stainless steel was invented (1913). Alloy steels do date back somewhat earlier. Last edited by dahermit; January 9, 2019 at 08:18 PM. |
|
January 9, 2019, 08:20 PM | #23 |
Senior Member
Join Date: September 23, 2013
Location: Alabama
Posts: 2,969
|
as cheap as magazine springs are I'd just buy new ones before I tried to monkey around with a gimmick.
|
January 9, 2019, 11:35 PM | #24 | |
Senior Member
Join Date: October 28, 2006
Location: South Central Michigan...near
Posts: 6,501
|
Quote:
|
|
January 10, 2019, 02:47 AM | #25 |
Senior Member
Join Date: April 7, 2006
Posts: 10,985
|
I use mostly 1095 high carbon steel for springs.
Occasionally, I use O-1, or 1084 high carbon. |
|
|