July 5, 2020, 03:24 PM | #1 |
Member
Join Date: June 29, 2020
Posts: 25
|
Slugging a barrel
Got meister barrel slugging kit. https://www.meisterbullets.com/AWSPr...-Rate-Included
Directions were pretty clear but still have a couple questions. I plan to call them, but it being Sunday, thought I'd see if I can get some answers here first. 1.I bought the number 5 kit which lists as correct for 9mm on thier site. .352-.364. The wooden rods that came with the kit do not fit in my barrels. I assume I'm not supposed to just pound them in. The are just barely to big to fit. Think they just sent the wrong size rods? Or am I missing something? 2.I assume I will need a hammer (with the correct size rod) to pound it through right? Just use a standard hammer or maybe a hard plastic one? Should I put the muzzle end on a wood block when I do it? |
July 6, 2020, 11:00 AM | #2 |
Senior Member
Join Date: February 15, 2009
Posts: 8,927
|
SAAMI specs for the 9mm Luger state bore diameter of .346 inch.
I think the wood rods are too big. |
July 6, 2020, 11:19 AM | #3 |
Staff
Join Date: September 25, 2008
Location: CONUS
Posts: 18,460
|
Bart B. is correct. The bore of a 9mm Parabellum is specified at .346 inches. Same for .38 Super.
9x18 (9mm Makarov) is .3543.
__________________
NRA Life Member / Certified Instructor NRA Chief RSO / CMP RSO 1911 Certified Armorer Jeepaholic |
July 6, 2020, 11:25 AM | #4 |
Senior Member
Join Date: August 25, 2008
Location: In the valley above the plain
Posts: 13,424
|
Wrong dowels.
But... Pounding a slug once it's in the bore is a great way to get it stuck, and/or shatter the dowels and wedge them in place. Wood is also not a great idea, since the dowels tend to split length-wise and act as wedges in the bore. Once a slug is started (by tapping, not pounding), you should be able to push it with only hand pressure on an appropriate rod. Pushing by hand is also how you feel for constrictions or loose spots. (Brass rods are best. But I usually use O-1 drill rod, because I have 36" lengths in nearly every bore size from .218" to .466".) Pounding and/or wooden dowels are a great way to end up panicking, doing something bad, and looking like an idiot:
__________________
Don't even try it. It's even worse than the internet would lead you to believe. |
July 6, 2020, 01:16 PM | #5 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,061
|
Run a patch with a little light oil on it through the bore before slugging—just enough to barely touch the bore surface with it. It makes the slug start more easily and then makes it easier to push it the rest of the way through. I also always slug both from the breech end and from the muzzle, as the feel of moving the slug through the bore from the wider end will be different and reveal more faults than starting at the narrow end does. This is because the narrow end makes the slug too narrow to drag at all on the rest of the bore.
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
July 6, 2020, 05:47 PM | #6 |
Senior Member
Join Date: March 21, 2018
Location: AZ
Posts: 236
|
If you don't have a "kit" do you just use a lead bullet of caliber size? If it's unknown, do you guess ay the proper size slug?
Most people don't have different cal lead just lying around. |
July 8, 2020, 02:58 PM | #7 |
Member
Join Date: June 29, 2020
Posts: 25
|
Got a couple brass rods. Meister also responded to let me know he tested some rods and are going to send some replacements to me. The brass rods I ordered from Amazon are 6mm. I think they should do the trick.
THanks for the help! |
July 9, 2020, 06:08 AM | #8 |
Senior Member
Join Date: October 1, 2014
Posts: 314
|
I use hdy 50 cal round ball
|
July 9, 2020, 06:20 AM | #9 | |
Senior Member
Join Date: October 23, 2005
Location: US
Posts: 3,652
|
Quote:
Now I cast lead so I don’t have to go seeking fishing sinkers anymore.
__________________
Support the NRA-ILA Auction, ends 03/09/2018 https://thefiringline.com/forums/sho...d.php?t=593946 |
|
July 9, 2020, 06:58 AM | #10 |
Senior Member
Join Date: April 3, 2010
Location: Texas
Posts: 1,394
|
I've used the egg sinkers for fishing if you don't have any slugs available also.
__________________
ONLY TWO DEFINING FORCES HAVE GIVEN UP THEIR LIVES FOR YOU. ONE IS JESUS CHRIST FOR YOUR SOUL AND THE OTHER IS THE AMERICAN SOLDIER FOR YOUR FREEDOM. |
July 10, 2020, 07:02 PM | #11 |
Member
Join Date: June 29, 2020
Posts: 25
|
Barrels slugged.
CZ TSO: .3555-.356 Glock 17 Gen 5: .355-.3555 So can I use .356 in both of these barrels? Measuring was tougher than I thought. Last edited by mpmo; July 10, 2020 at 07:40 PM. |
July 11, 2020, 12:10 AM | #12 |
Senior Member
Join Date: October 23, 2005
Location: US
Posts: 3,652
|
If using lead I would go .3565 or .357 personally. As always, heed the lead through a Glock barrel warning. I know guys who have shot lead in factory Glock barrels and had no issues but they kept an eye on the fouling. I’m on the fence as to whether I would personally do it. Just so you are aware to keep an eye on it.
__________________
Support the NRA-ILA Auction, ends 03/09/2018 https://thefiringline.com/forums/sho...d.php?t=593946 |
July 11, 2020, 12:59 AM | #13 | |
Senior Member
Join Date: March 21, 2018
Location: AZ
Posts: 236
|
Quote:
that. Easy to bump up by light tapping, or shrink by rolling fetween 2 hard surfaces. Much cheaper than buying a bag of shot or box of bullets. |
|
July 11, 2020, 01:35 PM | #14 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,061
|
They are if they are pure lead. Unfortunately, due to lead hysteria, the ones I see now at Wallyworld or other general outlets are usually no longer lead. Make sure you can dent it significantly with your thumbnail before you buy.
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
|
|