|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
January 21, 2002, 02:46 PM | #1 |
Senior Member
Join Date: October 13, 2001
Location: Louisville KY
Posts: 298
|
Revolver timing problem?
If the primer (.38 Special) is being hit off center, does that indicate a timing problem on a revolver?
The primer is being struck about halfway from dead center to the outer edge of the primer. The gun seems to be reliable and accurate. Should I be concerned? THANKS! |
January 21, 2002, 03:27 PM | #2 |
Senior Member
Join Date: February 19, 2001
Location: Iowa
Posts: 141
|
Is it off center to the right or left, or up and down? Could be a off center fireing pin too.
|
January 21, 2002, 03:34 PM | #3 |
Senior Member
Join Date: October 13, 2001
Location: Louisville KY
Posts: 298
|
I just noticed it. I am not any kind of expert about this. I just wondered if this might be a sign of a developing problem.
I will look at it again after work. If I can't see what it is doing, I will take it back to the range in the next day or two. THANKS! |
January 21, 2002, 06:19 PM | #4 |
Senior Member
Join Date: October 29, 1999
Location: Dewey, AZ
Posts: 12,858
|
Might just be the way that gun strikes em.
Have somebody (with glasses on of course) hold a sheet of paper bout six inches out from the side, center even with the cylinder to barrel gap. Nuther sheet for other side. Both sheets should shot lots of powder n junk but NO pieces of bullet. No bullet pieces, no gross timing problem. Sam |
January 22, 2002, 12:42 AM | #5 |
Member In Memoriam
Join Date: March 17, 1999
Posts: 24,383
|
It should be easy to determine, using an empty gun, whether the cylinder is coming into alignment and locking up properly. If the gun uses a firing pin on the hammer, alignment can also be checked simply by looking down the barrel (EMPTY GUN!) and seeing if the chambers line up.
Also, what brand of revolver is it? This should not happen with a modern American revolver or something like a Korth, but such things are common with some of the cheap revolvers imported a while back or with some of the Spanish guns of the 1920 period. Jim |
January 22, 2002, 09:57 AM | #6 |
Senior Member
Join Date: October 13, 2001
Location: Louisville KY
Posts: 298
|
Sounds like GREAT advice! I will try these things ASAP.
The gun is a .38 special F.I.E. Titan Tiger with 4-in barrel. I bought it new about 20 years ago. It probably has less than 600 rounds in it. (It wasn't fired for several years.) I just like this gun. I guess after reading a lot of posts here on TFL, I may be getting a bit paranoid about malfunctions and reliability. From what I am hearing there may be nothing wrong with it but I will check it out as you guys have instructed. I REALLY appreciate the advice. Maybe one day I can do a better job of contributing ideas to the board but I still have a lot to learn. Thanks! Logistar |
January 22, 2002, 01:48 PM | #7 |
Member In Memoriam
Join Date: March 17, 1999
Posts: 24,383
|
Hi, Logistar,
I am glad your Titan revolver works OK, but it is not one of the high quality revolvers. If it is reliable and functions well, there really is no problem. As a personal matter, I would prefer something a bit better for serious purposes. Also, your revolver is not rated for +P or +P+ ammunition, so stick to moderate power .38 Special and you should be OK. Jim |
|
|