The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Gear and Accessories

Reply
 
Thread Tools Search this Thread
Old September 28, 2021, 09:52 AM   #1
Prof Young
Senior Member
 
Join Date: August 21, 2007
Location: Illinois - down state
Posts: 2,207
I can't find a holster that . . .

I have search all over the internet for a holster that fits a Sig 365, is OWB, clips on to belt, made of leather, and has a thumb break.

I've got a kydex paddle, but it's just uncomfortable.

Help?

Life is good.
Prof Young
Prof Young is offline  
Old September 28, 2021, 10:52 AM   #2
Doc Intrepid
Senior Member
 
Join Date: May 22, 2009
Location: Washington State
Posts: 948
You might take a look at Mitch Rosen's 'Premier-FD'. It can be ordered with a thumb break (see the 5JR-TB in photos on the link below).

https://mitchrosen.com/products/holsters/belt-holsters/

"Instead of traditional belt slots, the PREMIER-FD has two wide straps that loop over the belt and lock up with sturdy snaps. A great feature for those who prefer not to thread the belt through holster slots to put on and take off the rig. Quick on, quick off, with excellent security."

Not sure if this will work for you, but Rosen holsters I've used are a quality product.

Just an opinion.
__________________
Treat everyone you meet with dignity and respect....but have a plan to kill them just in case.
Doc Intrepid is offline  
Old September 28, 2021, 06:11 PM   #3
dahermit
Senior Member
 
Join Date: October 28, 2006
Location: South Central Michigan...near
Posts: 6,370
There a lot of hobby leather workers out there that may be induced to make what you want. Here is a basket-weave, full-flap, clip-on that I made for my S&W I frame .32 S&W Long.


I made it a clip-on because of expediency and intended use (on my own property, in my own woods). It can also be slipped on via belt loop behind the clip.

Last edited by dahermit; September 29, 2021 at 01:32 PM.
dahermit is offline  
Old September 29, 2021, 06:05 AM   #4
Lt.Nick
Junior Member
 
Join Date: July 12, 2021
Posts: 13
Almost all of my holsters are custom made.
Some I made myself, once you learn the process it's not hard, well not that hard.
I started using glue on the seams, just to hold while doing the sewing, and it helps a lot.
Lt.Nick is offline  
Old October 3, 2021, 12:49 PM   #5
KyJim
Senior Member
 
Join Date: July 26, 2005
Location: The Bluegrass
Posts: 9,061
I have a Mitch Rosen Premier referred to in post 2. Mine is for commander-sized 1911s. Great quality and very comfortable. It does ride a bit lower than most of my concealed carry holsters so you have to consider that when wearing a covering garment
KyJim is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:42 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2020 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.04318 seconds with 9 queries