October 11, 2018, 12:42 AM | #1 |
Senior Member
Join Date: September 10, 2015
Posts: 152
|
Optimum Brinell Hardness
I recently purchased my first two boxes of 135 grain round nose and DEWC hi-tek coated .358 diameter bullets from Bayou Bullets. They were more accurate than the coated Missouri 125 and 158 gr coated bullets which I have loaded in the past, which were also good. My problem is that I had a lot of leading using the same powders and similar mid-range charges. The bullets do not seem as soft as swagged bullets which I have also reloaded without excessive leading. Does anyone know the Brinell hardness number for the Bayou bullets?
|
October 11, 2018, 12:58 AM | #2 |
Senior Member
Join Date: December 10, 2014
Posts: 1,965
|
I don't know what is happening, but the reason for coating is to prevent leading.
Regarding hardness, you might be prudent to contact Bayou and ask the horse instead of unreliable internet dribble. |
October 11, 2018, 06:21 AM | #3 |
Junior member
Join Date: February 2, 2010
Posts: 6,846
|
"I don't know what is happening, but the reason for coating is to prevent leading."
me too |
October 11, 2018, 06:27 AM | #4 |
Senior Member
Join Date: June 17, 2010
Location: Virginia
Posts: 6,883
|
From their website: "Our bullets are cast from certified 92/6/2 alloy with a Brinell hardness of 16-17" ... above Lyman #2
If the bullet is even slightly undersize (and/or if a cylinder throat is under groove diameter/base is beveled), low-mid pressure loads will tend not to seal. |
October 11, 2018, 11:24 AM | #5 | |
Senior Member
Join Date: October 23, 2005
Location: US
Posts: 3,652
|
BH usually isn't a huge factor in leading as long as you are in a range acceptable for your application. Anything even moderately hard cast (say, BH of 12 or so) should not give major leading up to mid-.357 mag loads if everything else is right.
Quote:
__________________
Support the NRA-ILA Auction, ends 03/09/2018 https://thefiringline.com/forums/sho...d.php?t=593946 |
|
October 11, 2018, 11:32 AM | #6 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,060
|
DMY,
I suspect this is more likely to be a coating problem than a hardness problem, especially if it's a thick coating that requires them to make the bullet undersized to still be able to fit in the throat of the gun. In such an instance, gas cutting could be an issue.
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
October 11, 2018, 01:14 PM | #7 |
Senior Member
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
|
"...the reason for coating is to prevent leading..." Nope. It's to try and keep lead out of the air of an indoor range. Painting your bullets isn't going to prevent leading your barrel if you try to drive 'em too fast. Mind you, neither will hardening 'em.
__________________
Spelling and grammar count! |
October 11, 2018, 03:23 PM | #8 |
Senior Member
Join Date: March 28, 1999
Location: Tucson, AZ
Posts: 3,800
|
DMY. You didn't specify if you were shooting a revolver or semi but I'd guess a revolver. With that said, measure the diameter of the offending bullets. slug your bore for the groove diameter and last of all, run some of the bullets through the cylinder chambers. What we're looking for is first the groove diameter. Example: .38 Spl. .358". Bullets should be at least .358", preferably (at least in my guns) .359". Comes the tricky part, the throats of the cylinder should be at least .358" to .359" agin preferably .359" based on my guns. If the bullet is smaller than .358", say .357" or the throats are smaller than .358" the bullets will be sized down to the smaller size that will lead the barrel. I can shoot a properly size 158 gr. SWC at BHN 8 which is close to pure lead at full powder from my .357 Mag. and no leading. Cylinder throats and groove diameter are compatible so proper sizing finishes the triad.
I cast my own bullets and my normal alloy run 11 on the BHN scale. It can be water dropped to reach a hardness of 32 on the BHN scale should I need to do so. Properly sized rarely do any of the bullets deposit any lead in my barrels. Paul B.
__________________
COMPROMISE IS NOT AN OPTION! |
October 11, 2018, 11:32 PM | #9 |
Senior Member
Join Date: September 10, 2015
Posts: 152
|
Thanks for all of your replies. I have not slugged the barrel of my revolvers, but the thing which makes me suspect the hardness may be the culprit is this. Using similar mid-range charges of W231, Bullseye and TightGroup, I had significant (not severe) leading with the Bayou. The Missouris had vritually no leading. Both were Hi-Tek coated, although I suspect the Bayou coating may be a little thicker because none of it comes off during seating. If I don't align the Missouri perfectly before seating, a little coating will scratch off, but that could also be caused by the different round nose profile. I would like to make the Bayous work because they are more accurate out of my 3" and 6" L-frames.
|
October 12, 2018, 05:38 AM | #10 |
Senior Member
Join Date: June 17, 2010
Location: Virginia
Posts: 6,883
|
(Assuming cylinder throat isn't major problem)
Shoot`em hotter, and with a faster powder. (as paradoxical as that might seem) |
October 12, 2018, 08:15 AM | #11 | |
Senior Member
Join Date: November 14, 2017
Location: Finger Lakes Region of NY
Posts: 1,442
|
Quote:
Don
__________________
NRA Life Member NRA Certified Metallic Cartridge Reloading Instructor |
|
October 12, 2018, 08:42 AM | #12 |
Senior Member
Join Date: December 22, 2015
Posts: 887
|
Not sure why the MBCs worked well and the Bayou Bullets leave some lead behind. Looks like the Bayou Bullets are BN16-17, whereas the MBCs are available in either BN12 or BN16 (not sure which you used previously). The finished diameters might be different (which you could measure). The coating thicknesses could be different, or the coating processes could be different between the brands.
At this point, rather than chasing all the stuff that may be the issue, I would probably try some of MBC's coated 148gr. wadcutters. They are BN12 which is appropriate for midrange loads. |
October 12, 2018, 09:22 PM | #13 |
Senior Member
Join Date: July 5, 2013
Location: Arlington, TX
Posts: 127
|
Best piece of advice I can give you is quit using Bayou bullets and keep using Missouri Bullets until you find another bullet you like.
|
October 12, 2018, 09:30 PM | #14 |
Senior Member
Join Date: September 12, 2015
Location: Issaquah WA. Its a dry rain.
Posts: 1,774
|
Mic the bullets and get back to us.
__________________
Just shoot the damn thing. |
October 12, 2018, 10:43 PM | #15 |
Senior Member
Join Date: October 23, 2005
Location: US
Posts: 3,652
|
Chainsaw said it. Mic the diameter. And about a 95% chance this isn't a hardness issue. Too much is made of BH unless you're trying to push high velocities in a rifle, but even then paper patching is really a better route (I'm gonna do that one day).
Matt Dardas had a decent explanation of the importance of bullet fitment on his web page when his company was open. He even offered slugs to slug a barrel, and iirc be would measure it for you if you mailed it to him. He didn't have options for different hardness, he had options for projectile diameter.
__________________
Support the NRA-ILA Auction, ends 03/09/2018 https://thefiringline.com/forums/sho...d.php?t=593946 |
October 14, 2018, 12:17 AM | #16 |
Senior Member
Join Date: September 10, 2015
Posts: 152
|
Follow up
I took Dufus' advice and perused Bayou's website and Missouri's. The Missouris I used were all Cowboy action bullets (105 gn TC, 125 gn TCFP, 140 TCFP & 158 gr RN) with a listed Brinell hardness of 12. The Bayous are listed at 16-17. Checking my range results, the Bayous gave a higher feet per second with the similar charges, although the different profile, weight and seating depth explains some of the higher FPS. Bottom line is that I will try to push the bullet a little faster (around 850 fps for a 135 gr RN & DEWC) and see what happens. Still have about 1300 Bayous to load and shoot.
|
October 14, 2018, 11:57 AM | #17 |
Senior Member
Join Date: September 13, 2011
Location: SW Florida
Posts: 890
|
One of the bullet makers had a formula on their website that calculated the maximum BHN for reliable obturation in barrels. For 17 BHN it comes out to 24,000 psi for obturation. For 12 BHN it is only 17,000 psi. For the harder bullets, especially if they are even slightly undersized for your cylinder throats, you need more pressure. So either be more precise with your bullet diameters, or use the softer bullets.
|
October 14, 2018, 06:30 PM | #18 | |
Senior Member
Join Date: November 14, 2017
Location: Finger Lakes Region of NY
Posts: 1,442
|
Quote:
Don
__________________
NRA Life Member NRA Certified Metallic Cartridge Reloading Instructor |
|
Thread Tools | Search this Thread |
|
|