The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools Search this Thread
Old December 7, 2018, 05:59 AM   #1
dhom
Member
 
Join Date: January 13, 2013
Posts: 19
357 mag revolvers

The loads for 357 Mag are somewhat reduced pressure wise from what they used to be early on. My question is this------- Can you load a 158 HPXTP to 1350 fps in a 6" revolver? I am talking about staying in todays recommended pressure limits.
dhom is online now  
Old December 7, 2018, 06:33 AM   #2
105kw
Member
 
Join Date: June 30, 2017
Posts: 77
Loads for the .357 have gotten lighter in the past 30 years, just look at the old reloading manuals.

Hornady says their top load , with a powder I've never used, hits 1400 at their max.
They used a 8in Python, and Power Pro 300 MP.

Every gun is a little different, with one of my older Smith N frames, I'd start at mid range load and work up. Look for pressure signs.

Remember the manuals are a guideline.
105kw is offline  
Old December 7, 2018, 07:16 AM   #3
mete
Senior Member
 
Join Date: June 14, 2004
Location: NY State
Posts: 6,558
One of my reloading books tested a bunch of 357s with the same ammo -velocities ranged from 1200-1600 fps ! S&W had some problems when they made their 357 in a K frame. That was worsened when a big police shootout showed the need to train with more full loads , all 357 instead of 10% full and 90% 38s .
Start with mild and slowly increase that. We now have better ammo so a premium bullet helps as do +P loads in the 38 .
__________________
And Watson , bring your revolver !
mete is online now  
Old December 7, 2018, 08:02 AM   #4
rambo60+
Member
 
Join Date: June 27, 2018
Posts: 61
I have a rossi .38spl as my ccw five shot the 357 version is the same size if memory serves me correctly its big enough it fits my hands and small enough its concealable in almost whatever i wear i recommend getting a nemmisis pocket holster theyl set you back about 20 but are good pocket holsters
as far as the handling of the revolver it has an exposed hammer double or single action about 5lb pull da and goes down to about 2 if you use it single action and for being a 2 inch barrel its very accurate i can keep softball sized groups at 25m
cost me about $300
rambo60+ is offline  
Old December 7, 2018, 10:00 AM   #5
MSD Mike
Senior Member
 
Join Date: October 16, 2009
Posts: 179
You might get there depending on the gun. I load that bullet with 13.5 gr of 2400 and get right at 1200 fps out of my Model 28 with a 6" barrel. Heavier loads are shown in some manuals, I just haven't had a reason to try them out. So, you could try working up a higher 2400 load or go to 296 for a bit more velocity. Just be sure and work up to it watching for pressure signes in your gun.
Lol, my answer is maybe.

Mike
MSD Mike is offline  
Old December 7, 2018, 11:52 AM   #6
HighValleyRanch
Senior Member
 
Join Date: July 15, 2005
Posts: 3,108
I chronographed some Buffalobore .38 Special +P out of my brother's 6.5" blackhawk and got:
4. Ruger BlkHwk 6.5”/ BB .38 +P 158 grain Outdoorsman/ 1239 fps, 1218 fps

so I am sure that you could get much higher with .357!
__________________
From the sweet grass to the slaughter house; From birth until death; We travel between these two eternities........from 'Broken Trail"
HighValleyRanch is offline  
Old December 7, 2018, 03:23 PM   #7
SIGSHR
Senior Member
 
Join Date: September 13, 2005
Posts: 4,144
Is the reduction in 357 loads due to the proliferation of lighter framed revolvers ?
SIGSHR is offline  
Old December 7, 2018, 04:00 PM   #8
Hanshi
Senior Member
 
Join Date: April 23, 2017
Posts: 146
I only fire full power .357 rounds in my "N" frame S&Ws, and then sparingly. I normally shoot .38spl in the .357s. My everyday .357 load is a 150 to 168 grn swc over 12.5 grains of 2400 for 1150 fps to 1205 fps depending on barrel length. 15 grains of 2400 with a 158 jhp gets to 1280 fps.
__________________
Young guys should hang out with old guys; old guys know stuff.
Hanshi is offline  
Old December 7, 2018, 09:20 PM   #9
Eddietruett
Member
 
Join Date: June 15, 2017
Posts: 40
I shoot 158gr xtp's and Speer JPH over 1605gr of H110 and was getting over 1300 fps out of my 8 3/9" Model 686 IIRC. The same load of powder was giving about 150fps faster with the HyTek Coated Lead 158gr bullet. I also was getting around 1350fps with 180gr HyTek Coated Lead with 13.5gr of H110. I don't have the exact data as my chronograph got stolen out of the storage building by my backyard range and all of my records were in the case with it. Of course, the Coated lead will give higher velocity than the Jacket bullet with the same load of powder.
Eddietruett is offline  
Old December 8, 2018, 06:24 AM   #10
dhom
Member
 
Join Date: January 13, 2013
Posts: 19
I should have included this---I am shooting a GP100 6" and I have on hand 2400, 296, Imr4227, HS-6, and Unique. I am trying to get a load around 1350 fps+ with a 158 xtp for deer hunting. [with accuracy] So far I am going to start with 2400 @ 14-14.5 gr and 16.5 with 296. I have used similar loads with a nosler 158 gr HP [slightly less] and found the bullet to be too soft for my liking. I have and shoot revolvers from 357 mag up to 475 L so recoil is not a consideration. It seems to me with the new SAAMI standards you cannot reach this velocity range.

Last edited by dhom; December 8, 2018 at 06:31 AM. Reason: add info
dhom is online now  
Old December 8, 2018, 10:26 AM   #11
NoSecondBest
Senior Member
 
Join Date: December 7, 2009
Location: Western New York
Posts: 2,065
Quote:
I should have included this---I am shooting a GP100 6" and I have on hand 2400, 296, Imr4227, HS-6, and Unique. I am trying to get a load around 1350 fps+ with a 158 xtp for deer hunting. [with accuracy] So far I am going to start with 2400 @ 14-14.5 gr and 16.5 with 296. I have used similar loads with a nosler 158 gr HP [slightly less] and found the bullet to be too soft for my liking. I have and shoot revolvers from 357 mag up to 475 L so recoil is not a consideration. It seems to me with the new SAAMI standards you cannot reach this velocity range.
I've shot over fifty deer with the .357mag in a variety of revolvers. Some custom built and some off the shelf. Most were shot using the Hornady 158g XTP JHP bullet. I can tell you for a fact that keying in on velocity is not going to give you any significant edge in killing deer with a handgun. Spend your time looking for the most accurate load for your gun at mid-to-top velocity. A hundred feet per second won't give you a significant edge. The bullet you have chosen is one I keyed in on many years ago. I have found many bullets that work well, but none that actually worked any better. They are readily available, shoot with the best, and perform well on deer at just about any velocity. This bullet will expand very well at any reasonable range. I have dozens of recovered bullets and I have noted the difference in expansion a various distances. The .357mag, regardless of a hundred or so feet per second difference, will start to lose expansion properties beyond fifty yards. That's regardless of the velocity difference you can get out of your handgun. If you stick with handgun hunting you'll find that out over time. Spend your time looking for the most accurate load you can get, not the fastest. Speed doesn't kill, bullet placement does. Eddietruett posted a reply to your question. FWIW, I've communicated with him quite a bit over the last year and he's about as knowledgible an individual on this subject as you'll find. Send him a PM if you'd like to know more. He's spent a lot of time becoming an expert on this subject. Good luck hunting with your handgun.....it's a lot of fun.
Note: this year I shot three deer with a .357MAX rifle using the Hornady 158g XTP. This rifle was driving that bullet at 2300fps and the bullet held up well. In spite of shooting this bullet out of a rifle, it only expanded about .1" more than it did out of a handgun at considerable less velocity. It peeled back better and made a nice exit hole. I only recovered one in a deer, and it was .602" and still weighed 125g recovered. That's about as well as it does out of my 686 driven at 1275fps.

Last edited by NoSecondBest; December 8, 2018 at 10:33 AM.
NoSecondBest is offline  
Old December 8, 2018, 10:38 AM   #12
Buckeye!
Senior Member
 
Join Date: September 1, 2008
Posts: 747
https://www.underwoodammo.com/produc...=7865902497849

Seems like Underwood has it under control... I have a few boxes ...

https://youtu.be/bJk_YHO6hDk

You tube vid shows testing in 4 inch barreled GP100 and 18inch barrelled carbine

Last edited by Buckeye!; December 8, 2018 at 10:45 AM.
Buckeye! is offline  
Old Yesterday, 06:46 AM   #13
dhom
Member
 
Join Date: January 13, 2013
Posts: 19
Thanks for your replies. Based on the responses I gather you can not get 1350 fps out of a 158 XTP at todays pressure limits.
dhom is online now  
Old Yesterday, 09:20 AM   #14
HighValleyRanch
Senior Member
 
Join Date: July 15, 2005
Posts: 3,108
Sure you can.
From BB's own website and their chrono results are from real world guns and I have found them to be realistic.

4-inch S&W L frame Mt. Gun

a. Item 19A/20-180gr. Hard cast LFN = 1375 fps
b. Item 19B/20-170gr JHC = 1411 fps
c. Item 19C/20-158gr. Jacketed Hollow Point = 1485 fps
d. Item 19D/20-125gr. Jacketed Hollow Point = 1603 fps
__________________
From the sweet grass to the slaughter house; From birth until death; We travel between these two eternities........from 'Broken Trail"
HighValleyRanch is offline  
Old Yesterday, 10:14 AM   #15
Real Gun
Senior Member
 
Join Date: May 19, 2004
Location: SC
Posts: 2,576
Quote:
Thanks for your replies. Based on the responses I gather you can not get 1350 fps out of a 158 XTP at todays pressure limits.
The first response to your post refuted that.


Alliant load data for a 158 Gold Dot HP includes:

Minimum OAL(inches) -Bbl Length - Primer - Powder - Charge Weight(grains) - Velocity
(fps)

1.575 - 10 - Fed 100 - 300-MP - 18.6 - 1,686
Factoring 10" barrel to 6", you'd think would still be well above 1350 fps.
__________________
Not an expert, just a reporter.
Real Gun is offline  
Old Yesterday, 12:07 PM   #16
laytonj1
Senior Member
 
Join Date: June 1, 2005
Location: Alabama
Posts: 4,149
Quote:
Sure you can.
From BB's own website and their chrono results are from real world guns and I have found them to be realistic.
It's my understanding that BB uses a special powder blend, not available to reloaders.

Jim
laytonj1 is offline  
Old Yesterday, 12:57 PM   #17
HighValleyRanch
Senior Member
 
Join Date: July 15, 2005
Posts: 3,108
Oh, I didn't know we were in the "reloading" forum!
If it's available in a commercial load, why not just use it? You're not going to be shooting a ton of it.
__________________
From the sweet grass to the slaughter house; From birth until death; We travel between these two eternities........from 'Broken Trail"
HighValleyRanch is offline  
Old Yesterday, 01:15 PM   #18
laytonj1
Senior Member
 
Join Date: June 1, 2005
Location: Alabama
Posts: 4,149
Quote:
Oh, I didn't know we were in the "reloading" forum!
Quote:
Can you load a 158 HPXTP to 1350 fps in a 6" revolver? I am talking about staying in todays recommended pressure limits.
Sure sounds like that was what the OP was asking.
Anyway, the point was you can't always match what a specialty ammo maker can obtain velocitywise as they have access to powders we don't.

Jim

Last edited by laytonj1; Yesterday at 09:24 PM.
laytonj1 is offline  
Old Today, 12:59 AM   #19
DWFan
Senior Member
 
Join Date: April 25, 2008
Posts: 282
According to Western Powder, a 158gr XTP-HP over 13.8gr of AA#9 will generate 1350+ fps from a 6" S&W. I can't verify this. I haven't used AA#9 in years.

Last edited by DWFan; Today at 01:07 AM.
DWFan is offline  
Old Today, 06:36 AM   #20
dhom
Member
 
Join Date: January 13, 2013
Posts: 19
I need to ask, have you chronod that load with 300 MP to know that is real world figures?
dhom is online now  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:56 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.11383 seconds with 9 queries