The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools Search this Thread
Old December 8, 2018, 12:33 AM   #1
wmg1299
Senior Member
 
Join Date: March 14, 2013
Location: DFW Metroplex
Posts: 122
New vs. Classic S&W Model 19

I was discussing my newfound appreciation of revolvers while shooting with my father-in-law. He worked as a police officer for a few years after returning home from Vietnam, and mentioned how he loved shooting his duty-issued Model 19 (most likely an early 70's model). The way he raved about that pistol made me consider picking one up. Are the current Model 19's significantly different than the one he carried? If picking up an older Model 19 is recommended, are there any versions or production years that should be avoided? Lastly, was the gun really that good, or has his fondness for the pistol been affected by nostalgia?
wmg1299 is offline  
Old December 8, 2018, 01:45 AM   #2
10-96
Senior Member
 
Join Date: October 19, 2005
Location: Tx Panhandle Territory
Posts: 3,722
The classic 19's reputation kinda grew bigger than the pistol in some ways. It is, and was, a very fine handgun. It fit the hand well with a whole slew of grips available, and it was unheard of to have accuracy issues. It's drawback was it's frame strength. S&W recommended that they be shot way much more with .38SPL loads and only qualifications be carried out with full house .357 loads. They were a far sight more comfortable to carry than the bigger N-framed pistols. I wouldn't give my 19-4 up for a whole truck load of speckled pups.

The smoothness of the action was better than the Ruger. And, in my experience, they felt better than a great many Colt Trooper I's, II's, and III's that I've felt. A good trigger job could bring it on par with some of the other Colts. The benefit over the Colts were the number and operation of the interior parts- there were fewer and simpler parts in a S&W. The Colt had a habit of making parts do two or three different things, and it took a fairly well trained man to diagnose and correct Colt problems once they wore 'out of time'.

And, I wish I could remember, but early Silhouette and/or other target shooters use to either put Colt Barrels on S&Ws or vicey versy.

I assume the new ones are as good or maybe even better than the old ones. I just can't bring myself to appreciate not seeing a firing pin nose on a new hammer. And, there are still plenty of folks who bemoan the MIM parts used on modern firearms. I don't like it, but then again- I have never seen such a part fail.
__________________
Rednecks... Keeping the woods critter-free since March 2, 1836. (TX Independence Day)

I'm going to use the words "clip" and "Long Colt" every chance I get. It grinds my gears to see new members attacked when we all know dang good and well what's being refered to.
10-96 is offline  
Old December 8, 2018, 06:44 AM   #3
mk70ss
Senior Member
 
Join Date: January 12, 2008
Location: Tennessee
Posts: 957
There is nothing like an early vintage Model 19 in terms of a quality, classic, classy wheelgun.
__________________
Say when.....
mk70ss is offline  
Old December 8, 2018, 08:31 AM   #4
jar
Senior Member
 
Join Date: March 8, 2001
Location: Deep South Texas
Posts: 974
There has to be at least one M-19 in the DFW area you can try out. Call around to the different ranges and see if there is one you can rent.

Warning, they can be like potato chips.
__________________
To be vintage it's gotta be older than me!
jar is offline  
Old December 8, 2018, 11:10 AM   #5
pete2
Senior Member
 
Join Date: May 15, 2012
Location: Texas
Posts: 1,791
The Model 19 is still my favorite handgun. I have a 6" and a 2-1/2", need the 4" but I have 2 4" L frames and a Model 15. An older S&W revolver, K or N frame , are the best there is. The newer ones I have are dang good too. The later L frame guns are also shooters, again the older the better. I have a 586 no dash that prolly shoots better(double action) than anything else I own. Colt and Ruger guns are good but the S&W action is way better.
pete2 is offline  
Old December 8, 2018, 11:14 AM   #6
Driftwood Johnson
Senior Member
 
Join Date: January 3, 2014
Location: Land of the Pilgrims
Posts: 1,745
Howdy

This is my Model 19-3 that I bought brand-spanky new in 1975. The action is still as silky smooth as it was when I bought it.








Quote:
It's drawback was it's frame strength. S&W recommended that they be shot way much more with .38SPL loads and only qualifications be carried out with full house .357 loads.
Not quite correct. It is not the frame, it is the forcing cone that can be the issue. S&W K frame 38 Special revolvers have a clearance cut at the bottom of the forcing cone. They have had this feature since about 1905. The reason is there needed to be clearance for the gas ring on the yoke to clear the bottom of the barrel. With 38 Special revolvers this was never a problem.

This is a photo of the clearance cut on the forcing cone of a S&W K-38. You can see the flat cut reduces the thickness of the forcing cone at that point.






This is the clearance cut on my 19-3.






What can happen with a K frame revolver that is chambered for 357 Magnum, if firing high velocity, light weight bullets, such as 125 grain bullets, the forcing cone can crack at its thinnest point. This is a well documented problem with K frame 357 Magnums and light weight, high velocity ammunition.

Like this:





I have had my Model 19 for over 40 years and it is still going strong. However I will admit that the great majority of ammunition I have put through it over the years has been 38 Special.

S&W developed the L frame for exactly this reason. It allows for a little bit more space for the gas ring, and it is not necessary to relieve the bottom of the forcing cone.

Regarding the Model 19s presently being offered by S&W, they may have addressed this problem, I am not sure about that.
Driftwood Johnson is offline  
Old December 8, 2018, 11:26 AM   #7
CajunBass
Senior Member
 
Join Date: May 6, 2005
Location: North Chesterfield, Virginia
Posts: 4,490
I'm not the guy to ask if one is "better" than the other. I've got an "old" one, and a "new" one. I think they're different, but I couldn't tell you which one is "better."

I like both.

19-4





19-9





Many years ago, a guy named Skeeter Skelton convinced me that the best all around handgun was a medium frame 357 with a 4" barrel. I haven't seen anything since then to make me change my mind.
__________________
For God so loved the world, that He gave His only begotten Son, that whoever believes in Him should not perish, but have everlasting life.
John 3:16 (NKJV)

Last edited by CajunBass; Yesterday at 10:45 AM.
CajunBass is offline  
Old December 8, 2018, 11:52 AM   #8
mrcharlie3531
Member
 
Join Date: February 22, 2013
Posts: 79


This is my 19-3. I recently got. I love it.
mrcharlie3531 is offline  
Old December 8, 2018, 04:11 PM   #9
riverdog
Senior Member
 
Join Date: August 11, 2000
Posts: 819
I have two Model 19’s, a 4” 19-5 former duty piece which is very smooth with an excellent trigger and noticeable holster wear; and a 6” 19-4 with target sights & trigger, and no holster wear. I shoot .38 Spl +P in the 4” 19-5 and .38 Spl target ammo only in the 19-4. Neither is really better, they’re just set-up differently.

The .357 Mag ammo here is all 158 gr., but is only for my L and N-frames.

Last edited by riverdog; December 8, 2018 at 07:10 PM.
riverdog is offline  
Old Yesterday, 07:42 AM   #10
shurshot
Senior Member
 
Join Date: August 25, 2006
Posts: 1,017
Bill Jordan was responsible for S&W introducing the model 19, as a Lawman's sidearm. As previously mentioned, it was designed primarily to be shot with .38's, and used sparingly and carried with .357 Magnums. I have owned quite a few 19 and 66's over the years and belted tons of 125 Magnums through them too (before knowing any better... LOL!), without any issue, aside from ringing ears. Now my vintage 19-3 Combat Magnum snubby and 80's Taurus 66, 6"(copy of 19), are regulated to only .38's and occassionally 158 Magnums.
My Ruger GP-100 3" can shoot up all my remains stock of 110 and 125 .357 Magnums.

Last edited by shurshot; Today at 05:26 AM.
shurshot is offline  
Old Yesterday, 10:08 AM   #11
Crunchy Frog
Senior Member
 
Join Date: December 26, 2008
Location: Greenville, SC
Posts: 521
The current Model 19, like the reintroduced Model 66 that preceded it, has a two piece barrel. It sort of reminds me of the Damon Wesson revolver that had a reputation for accuracy.
Crunchy Frog is offline  
Old Yesterday, 08:06 PM   #12
dannyb
Senior Member
 
Join Date: June 19, 2008
Location: SE PA
Posts: 289
My first center fire handgun was a model 19. I still have it, still take it to the range (today in fact), and once cleaned it goes back on my nightstand. Action is smooth as silk. I qualified for my Florida carry permit with it (despite the range officer telling me how much better I would do if I were using one of their rented Glock 17s).
__________________
Moron Lave (send a Congressman through the car wash)
dannyb is offline  
Old Yesterday, 08:27 PM   #13
44caliberkid
Senior Member
 
Join Date: May 15, 2017
Location: Iowa
Posts: 202
They're the greatest, my favorite Smith after the Model 29's. Currently have a stainless 2 1/2 inch and a blued 6 inch. Both were made in the the 80's.
44caliberkid is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:51 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06676 seconds with 9 queries