The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools Search this Thread
Old January 3, 2011, 02:23 PM   #1
cornbush
Senior Member
 
Join Date: September 29, 2008
Location: The retarded place below Idaho
Posts: 1,408
Hand chamber with finish reamer

Has anyone reamed a chamber by hand with out taking the barrel off.
Thinking about Ackley improving a 1903 Springfield, but dont want to remove the barrel.
Can I get a finish reamer and very slowly open it up by hand?
__________________
The best shot I ever made was an accident
cornbush is offline  
Old January 3, 2011, 02:50 PM   #2
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
This is a very common use for pull-through reamers. But be careful, or you may end up taking the barrel off anyway.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Scorch is offline  
Old January 3, 2011, 03:01 PM   #3
James K
Member In Memoriam
 
Join Date: March 17, 1999
Posts: 24,383
Yes, of course. It was done that way before pull through reamers ever existed.

Jim.
James K is offline  
Old January 3, 2011, 04:03 PM   #4
cornbush
Senior Member
 
Join Date: September 29, 2008
Location: The retarded place below Idaho
Posts: 1,408
I couldn't figure why it wouldn't work, just wanted to see if anybody had done it, I know if I go too deep.....the barrel comes of anyway.
thanks
__________________
The best shot I ever made was an accident
cornbush is offline  
Old January 3, 2011, 11:19 PM   #5
James K
Member In Memoriam
 
Join Date: March 17, 1999
Posts: 24,383
Use an extender to reach through the action. Take it very slowly and use lots of cutting oil. After a few times, you get a feel for when you are getting close, but on a one-time job, just take it slow, make a turn, flush, use the GO gauge, do another turn, etc. Tedious.

Jim
James K is offline  
Old January 3, 2011, 11:27 PM   #6
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 18,486
Aren't you supposed to set the barrel back a turn for an AI anyhow?
Jim Watson is offline  
Old January 4, 2011, 12:53 AM   #7
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 15,248
Quote:
Aren't you supposed to set the barrel back a turn for an AI anyhow?
Technically yes, but I have seen them done without it. It leaves a very small area at the base of the neck uncut, but it will make little or no difference.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Scorch is offline  
Old January 4, 2011, 12:41 PM   #8
brickeyee
Senior Member
 
Join Date: December 29, 2004
Posts: 3,351
The problem is cutting to the base of the neck without going even the slightest bit deeper.

Precision chambering is done with dial indicators to monitor depth throughout the cut.
brickeyee is offline  
Old January 4, 2011, 02:07 PM   #9
HiBC
Senior Member
 
Join Date: November 13, 2006
Posts: 8,274
I have had good results hand turning a reamer.Between the reamer pilot and the old chamber to follow.The reamer will want to self center and cut true.What will mess that up is if you are appying any side loads as you turn it.A Crescent wrench is not OK.You need a tee handle.There is a feel to rotating around the axis without applying side loads.It would not hurt if your driver extension had a portion that is about bolt diameter to be supported by the rear receiver ring.You need to be able to draw the reamer out of the cut as you are turning it in the clockwise cutting direction.This means the driver needs to hold on tight to the reamer.Seems like a tool I made was bored/reamed to a close slip fit to just accept the reamer shank diameter.I then drilled and tapped for a couple of set screws to engage the square shank of the reamer.The other end of this driver was cross drilled for the tee handle,I think I used a 10 inch ejector pin.This worked good.
I suggest having a 1 lb coffee can with some solvent and a toothbrush handy.Every time you withdraw the reamer,wash all chips off with the toothbtush,and use a cleaning rod,patches,air,to make sure all chips are clear before you go back in with the reamer.You really do not want a chip bridged across a cutting edge.
Ackley designedd the AI's to use the juncture of the shoulder and neck as an alternate headspacing feature for fireforming or using factory ammo in a pinch.
I load long bullets into the rifling to hold my brass to the bolt face when I form cases.I also headspaced the chamber tight,mine was not a conversion.

You might evaluate how tight/loose the original headspace is before you begin.If it is tight,just don;t cut too deep and you will be fine.If it is already loose,the setback idea is worth consideration.If this is a personal rifle that you will keep,and you are carefully handloading fireformed ammo,it is workable.I think headsp-ce gages specific to the AI's are available
HiBC is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:31 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.06502 seconds with 8 queries