October 10, 2012, 01:00 PM | #1 |
Member
Join Date: March 8, 2012
Location: NY
Posts: 33
|
1911 question
Just this morning I noticed by grip safety is not operative on my 1911. It has approx. 12k rounds through it. I'm guessing it's time for a new sear spring. Is there anything else I should be checking?
Thanks jjcbuck |
October 10, 2012, 01:23 PM | #2 |
Senior Member
Join Date: October 28, 2006
Location: South Central Michigan...near
Posts: 6,501
|
Has it worked since the last time you had the gun apart? You can get the finger of the spring that is supposed to operate the grip safety over the grip safety instead of under...then it does not work. Or, you might have bent it... In any event, take it apart and look at the spring; I cannot imagine it not working if it is not broken off.
|
October 10, 2012, 01:31 PM | #3 |
Member
Join Date: March 8, 2012
Location: NY
Posts: 33
|
1911 question
It is in the right place - it appears to have a slight roll to the left that may be caused by the contact point on the grip safety which also seems to be slightly rounded to the left. Bending that right tang back a little seemed to activate the grip safety again buy after a few times it ceased working again.
|
October 10, 2012, 03:20 PM | #4 |
Senior Member
Join Date: June 24, 2012
Posts: 1,055
|
Both sear spring and grip safety are inexpensive replacement parts,they show signs of wear and they don't work,bending the grip leaf temporarily resolves the issue it could be that it has lost functionality and in addition may have damaged the grip safety.New ones are likely the solution.
|
October 10, 2012, 03:39 PM | #5 |
Junior member
Join Date: February 2, 2008
Posts: 3,150
|
If you're saying you bent the spring back and it immediately went weak again then that spring has no temper and is junk. Buy new one from Brown, Wilson or any of the big names. Factory springs are mostly junk. Is it the orginal factory spring? How old is it?
|
October 10, 2012, 09:09 PM | #6 |
Member
Join Date: March 8, 2012
Location: NY
Posts: 33
|
1911 question
As I mentioned the gun has approx. 12k rounds through it and has never been refurbished except for a new extractor. All other components are original and about 8 years old. A local smith built it for me and has now moved away. Caspian race ready frame (Commander) and a Caspian slide. Mostly Ed Brown guts. I have no complaints.
Thanks for the input |
October 11, 2012, 09:52 AM | #7 |
Senior Member
Join Date: March 26, 2005
Location: Osborn, Missouri
Posts: 2,697
|
In all my years of working on 1911's I've never had a sear spring lose it's tension.
However I'm not saying that can't happen. If Caspian cut the frame for the grip safety sometimes the radius cut they do is very generous, thus allowing the grip safety a lot of wobble. This along with other things may be the problem. Here's something else to check. The slot in the grip frame that the tab on the sear spring fits into to hold it in place may be to large allowing the sear spring to walk to the left. If this is the case stake the slot in the frame on the left side of the tab. Also check to make sure the tab on the sear spring is not sheared off the spring. Best Regards Bob Hunter www.huntercustoms.com |
October 11, 2012, 10:31 AM | #8 |
Junior member
Join Date: February 2, 2008
Posts: 3,150
|
Maybe it just needs a little more "bend".
|
October 11, 2012, 10:38 AM | #9 |
Senior Member
Join Date: June 24, 2012
Posts: 1,055
|
The Occam's Razor principle states that when there are two solutions to a problem the simplest one is the right one.Eight years and 12,000 rounds later is a fairly long period of time for a machining traced issue to show up.Odds on a new sear spring does it,I would also replace the safety because of the wear signs,however failing that I would then proceed to stake things on but then I would be staking new parts and not be out that much.
|
October 12, 2012, 09:11 AM | #10 |
Member
Join Date: March 8, 2012
Location: NY
Posts: 33
|
1911 question
spring appears to be seated and riding the grip safety properly.
I have an Ed Brown sear spring on the way - I will keep you posted. Thanks for the time and input. |
October 12, 2012, 03:46 PM | #11 |
Member
Join Date: March 8, 2012
Location: NY
Posts: 33
|
1911 Question
OK - the Ed Brown sear spring arrived an hour ago and my problem is solved. Grip safety is once again fully functional.
Brownell's service was exceptional - regular mail. Thanks to those offering advice. |
October 13, 2012, 12:24 AM | #12 |
Senior Member
Join Date: April 3, 2005
Location: Seattle
Posts: 827
|
Gunsmith.
__________________
"Huh?" --Jammer Six, 1998 |
October 15, 2012, 04:45 AM | #13 | |
Senior Member
Join Date: May 17, 2004
Location: NC Piedmont/Foothills
Posts: 666
|
Springy
A quick test.
Cock the hammer and apply light upward pressure on the underside of the grip safety tang. Pull the trigger. If the hammer falls, you have a grip safety problem. If it doesn't, you have a spring problem. Quote:
Um...Yer gonna hafta 'splain that one. You can get the left leg under the sear, and have the hammer fail to cock...but the right leg over the grip safety? That'd be a trick.
__________________
If your front porch collapses and kills more than three dogs...You just might be a redneck Last edited by 1911Tuner; October 15, 2012 at 04:51 AM. |
|
Thread Tools | Search this Thread |
|
|