August 8, 2011, 10:19 AM | #1 |
Senior Member
Join Date: October 4, 2010
Location: Chattanooga, TN
Posts: 466
|
Bolt Handle Repair
I have a older Remington Targetmaster single shot .22 (Model 510); yesterday when I removed it from the case I found the bolt handle broken (about halfway down the "neck" - there's about an inch left on the bolt, and an inch yet on the bolt knob).
I would like to repair this if possible; it was my mother's .22, and my uncle engraved both the receiver and the bolt handle. Is there an adhesive (JB Weld or the like) that would be strong enough to reattach the bolt knob and adhere under use? Or do I need to just find another Targetmaster, use it's bolt, and keep the original bolt for sentiment / display purposes?
__________________
NRA Life Member |
August 8, 2011, 10:24 AM | #2 |
Senior Member
Join Date: June 20, 2007
Location: Rainbow City, Alabama
Posts: 7,167
|
No adhesive would come close to being strong enough. Yes, it can be rewelded. A cheaper solution is to find a used bolt. I'd hit Numrich first, then Gunbroker. A bolt from a 510, 511, or 512 will work (they are all the same bolt).
|
August 8, 2011, 10:47 AM | #3 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,063
|
If you want to keep the original, find someone who is a good TIG welder. See if he can do the welding without touching the engraving and can clean the weld up flush with the outside afterward. Some of those guys can weld a crack in car body steel. With an inch of extra room to spare, the heat won't likely spread to the bolt, though you want to strip it and get the springs and firing pin out before proceeding. The gun will need refinishing afterward, which is why you don't want to braze it. The brazing filler won't accept the same finish.
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
August 8, 2011, 04:09 PM | #4 |
Member In Memoriam
Join Date: March 17, 1999
Posts: 24,383
|
That is an inexpensive .22 and trying to keep it "original" by welding will cost a lot more than just replacing the bolt handle, which Gun Parts lists at around $30. Sure a good welder can do it, but not for that price.
Jim |
August 9, 2011, 07:59 AM | #5 |
Senior Member
Join Date: October 4, 2010
Location: Chattanooga, TN
Posts: 466
|
I think I'm going to purchase a replacement bolt handle from Numrich, and next month have the original bolt handle rewelded. I'm also starting to keep an eye out on the various auction sites for another 510 Targetmaster - it's usually the most popular rifle when I introduce newbies to shooting, and it would be handy to have another.
James: I agree it isn't worth the value of the gun to have it rewelded, but it's more than worth the value of the gun's sentiment.
__________________
NRA Life Member |
August 9, 2011, 04:24 PM | #6 |
Senior Member
Join Date: December 6, 1999
Location: Richmond, Virginia USA
Posts: 6,004
|
What's a tig welder charge these days to fix a bolt handle, $25 or $40?
Check this guy's work. www.straightshotgunsmithing.com |
August 29, 2011, 12:13 PM | #7 |
Senior Member
Join Date: October 4, 2010
Location: Chattanooga, TN
Posts: 466
|
Good news! The gunsmith that works with my LGS will have a professional TIG welder refasten the broken bolt handle together. Cost is around $25, so not too bad
__________________
NRA Life Member |
|
|