The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools Search this Thread
Old August 15, 2010, 07:38 PM   #1
davem
Junior member
 
Join Date: October 4, 2004
Posts: 458
44/40

I am sort of interested in the old 44/40 but have avoided the cartridge because of all the stories you hear about bulging the case while crimping a reload. In any event there's some reasons I would like the 44/40. First, it is a historically correct cartridge that could be used in both a revolver and lever action rifle. Second, I am told that with a modern case the 44/40 can SAFELY be reloaded to much higher pressures, maybe not up to 44 Magnum but certainly higher than the traditional loads. That would be of interest if a 1873 Winchester could safely handle the load, then the gun could be used for deer hunting.
In any event, I am interested in anything "44/40", if any off you reload and shoot this cartridge.
davem is offline  
Old August 15, 2010, 07:46 PM   #2
MJN77
Senior Member
 
Join Date: April 27, 2009
Location: on a hill in West Virginia
Posts: 789
While not the best choice in ammo, I have killed several deer with factory .44-40 "cowboy" loads out to 70 yards. Never took more than one shot, and none of them went more than 50 feet before they went down. You just have to hit them in the right spot. I have moved on to full charge black powder loads.
MJN77 is offline  
Old August 16, 2010, 12:01 AM   #3
olyinaz
Senior Member
 
Join Date: February 24, 2009
Location: Arizona
Posts: 877
You might want to ask the same question here:

http://www.levergunscommunity.com/viewforum.php?f=1

Oly
olyinaz is offline  
Old August 16, 2010, 02:38 AM   #4
Rusty.it
Member
 
Join Date: May 29, 2007
Posts: 50
I reload 44/40 for a '73 replica and for a revolver remington '75 replica!
You can bulge one or two case the first time for setting the dies and no more!
44/40 has a better seal of the chamber in lever action, and has no blow from action, the 45 colt sometime has it.
I reload sometimes with black powder, but my favourite load is with smokeless, i can't give you a recipe why i use european powder like vhitavuori, or the cheap rex powder.
A fiend of mine reload for a '66 yelloboy with 18-20 grains of N105, i think is too heavy for the toggle link action of '66-'73 winchester, but he is happy with this strong rounds!
ciao
Rusty
Rusty.it is offline  
Old August 16, 2010, 07:34 AM   #5
MJN77
Senior Member
 
Join Date: April 27, 2009
Location: on a hill in West Virginia
Posts: 789
It has been said for years (true or not) the .44-40 round has killed more deer than any other cartridge except the .30-30.
MJN77 is offline  
Old August 16, 2010, 08:42 AM   #6
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 41,375
I used to reload the .44-40 for a friend.

It was pretty frustrating at first, as I really smashed a couple of cases, but once you get the hang of it, that becomes a non issue.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old August 16, 2010, 09:02 AM   #7
salvadore
Junior member
 
Join Date: January 1, 2007
Location: Idaho
Posts: 2,282
I don't reload or have ever owned a 44/40. As a 32/20 fan however I strongly recommend a lee crimp die.
salvadore is offline  
Old August 16, 2010, 12:11 PM   #8
shafter
Senior Member
 
Join Date: December 23, 2009
Posts: 1,624
I can't imagine what hunting deer with a 44-40 '73 would be like. Someday.....
shafter is offline  
Old August 16, 2010, 12:41 PM   #9
RickB
Senior Member
 
Join Date: March 1, 2000
Location: Boise, ID
Posts: 8,513
I've loaded more than a few hundred .44-40 rounds, and usually expect to lose 2%-3% of the cases during a reloading session. I've never loaded it hot, but do remember Col. Askins wondering what all the fuss was about the .44 Special, when the WCF could do the same things.
RickB is offline  
Old August 16, 2010, 10:20 PM   #10
davem
Junior member
 
Join Date: October 4, 2004
Posts: 458
Well that's sort of where I was headed. As I understand when the 44/40 first came out it had a balloon case, the black powder 40 grain charge of the day was about maximum. Nowadays the 44/40 cases aren't balloon, they are the same type case (full web- if that's the right term-as with the 44 special. 44 magnum, etc- so the case can be loaded to a higher level, at least that's my understanding. The issue is in a 1873 Winchester, I'm not sure if the action is strong enough to accept more pressure. A modern manufactured Colt Peacemaker however might be able to take the higher pressure, if it is the same steel as in one rated for 44 magnum. In any event, just wondering what some of you have done.
davem is offline  
Old August 17, 2010, 02:26 PM   #11
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 41,375
At one time Winchester offered a series of HS - High Speed - cartridges in a variety of calibers, including .32-20, .38-40, .44-40, and possibly others.

Essentially they were +P versions of those cartridges and were intended for use in the 1892 Winchester, NOT in the 1873 or older Colt revolvers.

People didn't bother reading the warnings on the boxes, though. Dropping an HS cartridge into an 1873 would normally blow the side plates off.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old August 17, 2010, 09:02 PM   #12
davem
Junior member
 
Join Date: October 4, 2004
Posts: 458
Thanks Mike, I think that answers my question in the respect that a plus P type load would not be suitable for a 1873 Winchester.
davem is offline  
Old August 21, 2010, 04:00 PM   #13
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 16,180
The biggest problem with reloading 44-40 is originals used .427 bullets and modern 44-40's use .429's. Most resizing dies stil size cases to .427. Trying to stuff a .429 bullet into a .427 case isn't easy as thin as they are. RCBS makes cowboy dies that do size to .429 but I just take a punch and bell mine a little.
Hawg is offline  
Old August 21, 2010, 11:06 PM   #14
Fingers McGee
Senior Member
 
Join Date: March 19, 2008
Location: High & Dry in Missouri Ozarks
Posts: 2,113
I've loaded thousands of 44-40 rounds with BP, Subs and that newfangled powder that don't smoke on a Hornady L-N-L using RCBS dies. Once you get the dies set right in a progressive press, crunching cases isn't a problem. I use the expander plug out of a .44 mag set of dies and haven't found a pressing need to use a factory crimp die. The roll crimp die works just fine.
__________________
Fingers (Show Me MO smoke) McGee - AKA Man of Many Colts - Alter ego of Diabolical Ken; SASS Regulator 28564-L-TG; Rangemaster and stage writer extraordinaire; Frontiersman, Pistoleer, NRA Endowment Life, NMLRA, SAF, CCRKBA, STORM 327, SV115; Charter member, Central Ozarks Western Shooters
Cynic: A blackguard whose faulty vision see things as they are, not as they should be. Ambrose Bierce
Fingers McGee is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:50 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.08495 seconds with 10 queries