|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Search this Thread |
October 14, 2001, 07:28 AM | #1 |
Senior Member
Join Date: June 17, 2001
Location: MA
Posts: 780
|
Which Reloading Kit For Beginner?
I never thought of reloading yet because I only own one firearm right now But after trying to find ammo for it lately I realize that besides saving money it also allows you to have fresh ammo on hand when the stores don't.Couls someone recommend a reloading kit for a beginner?I would be reloading .45ACP and 12 gauge and maybe .308 within the next few months.
Thanks, Kris |
October 14, 2001, 07:57 AM | #2 |
Senior Member
Join Date: November 20, 2000
Location: Ohio
Posts: 258
|
IIRC, there's no press around that'll do pistol, rifle and shotgun. You'll need a separate operation for the big shot shells.
I started with a Lee Anniversary ($79.00) set for pistol & rifle that came with a good book, a scale, powder measure, primer tool, and a press. You'll need to buy caliber-specific dies ($25.00) and a Lee Factory Crimping Die for pistol rounds. ($20.00, also caliber-specific.) This set-up will reload all the pistol and rifle calibers. You'll hear a lot about Dillon progressives and such on this board. They're great presses, but expensive and complicated. Start with a cheapy like this Lee single-stage set and work your way up to the big guys. You need to see and learn from all the mistakes that you and the machinery can make before you move up to high-volume automation. For shotgun, the stores I go to emphasize the MEC stuff......don't know anything about them, except their equipment seems to be reasonably priced. I think I've seen a starter set for about $100.00
__________________
We are born naked, wet, and hungry. Then it gets worse. |
October 14, 2001, 09:17 AM | #3 |
Senior Member
Join Date: June 17, 2001
Location: MA
Posts: 780
|
Thanks.I was looking at the Lee Anniversary kit.Good price and reputation.I have read that beginners should stay away from the progressive presses.
|
October 14, 2001, 10:09 AM | #4 |
Senior Member
Join Date: October 9, 1998
Location: Ohio USA
Posts: 8,563
|
While I personally recommend both Lee equipment, and also that beginners stay away from progressives, it's more from the standpoint of $$$, than anything else. Reloading on a progressive doesn't have to more complex or difficult than using a single stage, or a turret press like Lee offers.
I've been turning out reloads in .38, 9mm, .44 and ,45 colt and .45 acp for 20 years on my Lee turret press. IIRC, my original cost for just the press was $50 or $60 way back then. It stil works fine after years of service. When it does finally go, or maybe sooner if I decide to use it as a dedicated to one calber press, I plan on replacing it with a Dillon 550 simply because I'm able to afford one. In the grand scheme of things though, the cost of the press is just a small part of the total cost. The anniversary kit is a good econonical way to start. Lee carbide dies are among the best bang for the buck going, and the Lee factory crimp die is outstanding. zanthope is correct, you'll need a seperate setup for shot shells. |
October 14, 2001, 01:00 PM | #5 |
Senior Member
Join Date: July 27, 2000
Location: Over the Hills and Through the Woods, Tennessee
Posts: 1,207
|
Can't believe nobody's mentioned the RCBS Rockchucker kit. After doing my homework, that's the one I'm going for as soon as I find the cash. (Been busy spending all my spare cash on long guns.)
It will upgrade to progressive with a Piggyback II add on, and most folks say a Rockchucker will last a lifetime. Features listed at the RCBS page are: -Heavy-duty cast-iron construction for easy case resizing -1 in. ram held in place by 12 1/2 sq. in. of ram-bearing surface -Toggle block of ductile iron -Compound leverage system -Pins ground from hardened steel -1 1/4" x 12 thread for shotshell reloading dies and Piggyback II -7/8" x 14 thread adapter for standard dies and accessories -Milled slot and setscrews accept optional RCBS auto primer feed Now, I'm pretty curious about the two different thread sizes. If the 1 1/4" threads will fit shotshell reloading dies, can't you use this press for shotshell dies as well as standard dies with the thread adapter? Or does this mean that the Rockchucker comes in two different versions, one for shotshells and one for standard dies? Either way, you can't go wrong with the Rockchucker. Natchez usually has some good prices, though the bastards won't sell to me here in TN (or to my mom in AL, or to my uncle in GA....ggggrrrrr!!!!).
__________________
Gun control should just be about hitting your target. |
October 14, 2001, 01:09 PM | #6 |
Senior Member
Join Date: July 27, 2000
Location: Over the Hills and Through the Woods, Tennessee
Posts: 1,207
|
Found a couple of threads over at shooters.com that might interest you:
http://talk.shooters.com/room_47/6076.cfm#30555 http://talk.shooters.com/room_49/1730.cfm#5769
__________________
Gun control should just be about hitting your target. |
October 14, 2001, 03:45 PM | #7 |
Staff Emeritus
Join Date: November 23, 1998
Location: a small forest in Texas
Posts: 7,079
|
Folks,
We have a Handloading and Reloading Forum. The folks over there should be of more help than you'll find here in the General Forum. So, I'll move this thread over there. |
October 14, 2001, 06:33 PM | #8 |
Senior Member
Join Date: December 9, 1999
Posts: 4,131
|
KPS, although I'm a Dillon 50B user, and also own a Lyman Spartan (single stage) I believe that the first press a new handloader should consider is a good quality turret press (I have a Lyman Spart-T). They are strong press that won't break the bank, but will be considerably faster than a single stage. Later, if you get a progressive, you can still use the turret for unique operations.
As far as the shotshell press goes, you can look for an old Pacific press. A friend just purchased one for $25 and Hornady has all the bushings, so it's supportable. They're old, but work great...he cranked out about 75 shells in about 35 minutes his first time using it.
__________________
Favor the X. Steve Smith NRA Life Member |
October 14, 2001, 09:53 PM | #9 |
Member
Join Date: August 27, 2001
Location: Indiana
Posts: 70
|
The lee reloading kit is a great way to start, as others have said. About four months ago I decided to get into reloading. I was advised by many to get something other than lee. However I bought the lee anivesary kit and have had a great time reloading since. It is a very affordable and great way to learn about reloading. I can't think of anything bad to say about the lee kit.
|
October 15, 2001, 05:52 AM | #10 |
Senior Member
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,324
|
BUY BEST BUY ONCE
Suggest higher satisfaction with RCBS or REDDING starter kits; much higher quality, longer life expectancy.
__________________
. "all my ammo is mostly retired factory ammo" |
October 15, 2001, 11:22 AM | #11 |
Senior Member
Join Date: December 9, 1999
Posts: 4,131
|
I forgot to add this...search Ebay for great deals.
__________________
Favor the X. Steve Smith NRA Life Member |
October 16, 2001, 06:05 AM | #12 |
Senior Member
Join Date: October 6, 2001
Location: S.W. Michigan
Posts: 560
|
Hit the search button up in the right corner and search for Dillon. My first and only press for pistol and rifle has been a Dillon. I suggest you look at Hornady, RCBS, and Dillon progressives since your shooting pistol.
Try this site: http://dillonprecision.com |
October 17, 2001, 05:32 AM | #13 |
Senior Member
Join Date: June 17, 2001
Location: MA
Posts: 780
|
Natchez has the Rockchucker reloading kit for $119 on sale and that is quite a bit cheaper than everyone elses price.Is that a decent kit or should I hold off for a turret press kit?
|
October 17, 2001, 07:10 PM | #14 |
Senior Member
Join Date: September 4, 2001
Location: atlanta GA
Posts: 107
|
KPS, I would also recommend the Lee Anniversry Kit. I got one last year and I love it. Very strong, very simple and great instructions. Also it comes with everything except the dies and the powder and bullet components. Check out www.leeprecision.com. Good Luck, Weagle
|
October 17, 2001, 09:52 PM | #15 |
Member
Join Date: December 1, 1999
Location: Sherman,Tx,USA
Posts: 40
|
If thats $119 for the Master Reloading Kit then it is an excellent buy, but I bet its a misprint or just the press.
|
October 18, 2001, 05:22 AM | #16 |
Senior Member
Join Date: June 17, 2001
Location: MA
Posts: 780
|
catalog misprint
Yep, checked their website and see the kit is $219.95.Not the $119.95 advertised in their flyer.
|
October 18, 2001, 06:09 AM | #17 |
Senior Member
Join Date: April 24, 2000
Location: Northern Indiana
Posts: 519
|
Also may try
Try ihuntishoot.com. It's my local dealer and they had some close-outs on RCBS. Stuff was WAY cheap. When they were pricing, they took Midway & Cabella's lowest price and took another 25-30% off that. They have complete kits, dies, case cleaners, etc. They UPS anywhere. Phone is 219-462-4412.
Also, you might search around for a Dillon dealer in your area. I have a dealer that gets "used" in sometimes. I bought a Dillon that was older but never used. Got it for 1/3rd of new price. |
Thread Tools | Search this Thread |
|
|