The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools Search this Thread
Old January 23, 2020, 06:30 AM   #1
trapper.44shooter
Junior Member
 
Join Date: January 18, 2020
Posts: 8
LEE Production IV Casting Furnace

Hey fellas will this be a good one for me to start out with I am a total greenhorn on bullet casting BUT I am learning quickly by reading & watching some of the good casting vids on YouTube I am going to buy all LEE equiptment to start I am on a VERY TIGHT BUDGET the lead is much higher than I thought it would be oh I can get those "WHEEL WEIGHTS " all I want but how do I get them casted into good shooting round balls for my .44 1858 Bison 12" revolver
trapper.44shooter is offline  
Old January 23, 2020, 07:04 AM   #2
BBarn
Senior Member
 
Join Date: December 22, 2015
Posts: 858
Make sure the wheel weights are lead. The vast majority of wheel weights used in recent years are iron or zinc alloy and are not suitable for casting bullets. Many previous sources of lead wheel weights have disappeared in recent years.
BBarn is offline  
Old January 23, 2020, 11:36 AM   #3
mikld
Senior Member
 
Join Date: February 7, 2009
Location: Southern Oregon!
Posts: 2,889
Don't clean your wheel weights or scrap lead in your casting pot. Leaks are common with "dirty" alloy due to the design of the valve (not a bad thing, just something to remember). Get a Lyman Cast Bullets Handbook and read the "How To" section. Then practice, practice, practice. Then when you have problems, or just gathering info, look here; http://castboolits.gunloads.com/ Discussions on every aspect of lead bullets (alloys, lubes, methods, sizing, coating, loading and shooting to name a few)...

Good read;http://www.lasc.us/castbulletnotes.htm
__________________
My Anchor is holding fast!
I've learned how to stand on my own two knees...
mikld is offline  
Old January 23, 2020, 12:26 PM   #4
USSR
Senior Member
 
Join Date: November 14, 2017
Location: Finger Lakes Region of NY
Posts: 887
Quote:
Leaks are common with "dirty" alloy due to the design of the valve (not a bad thing, just something to remember).
Yep. There's a reason Lee pots are called "drip-o-matics".

Don
__________________
NRA Life Member
NRA Certified Metallic Cartridge Reloading Instructor
USSR is online now  
Old January 23, 2020, 11:36 PM   #5
Dufus
Senior Member
 
Join Date: December 10, 2014
Location: Texas
Posts: 1,876
Just a note: your wheel weights might be a little too hard for easy loading in a black powder gun, but it has been done.
Dufus is offline  
Old January 24, 2020, 07:09 PM   #6
kmw1954
Senior Member
 
Join Date: June 11, 2016
Location: SE Wisconsin
Posts: 1,346
For just a discussion on pots. The Lee Pro IV has it's own advantages and disadvantages and much of it depends on how you plan to use it. If you are going to at any time try to use a ladle you will find it very cramped and restricted. If casting a big bunch of bullets you will find it small and wanting. If all you are going to do is cast a few hundred at a time it will work great and melt alloy quickly and keep up.

So keep those issues in mind when making a decision. The Lee Pro 4-20 or the Magnum pots may be a better choice.
kmw1954 is offline  
Old January 24, 2020, 07:50 PM   #7
pete2
Senior Member
 
Join Date: May 15, 2012
Location: Texas
Posts: 2,131
I have 2 of the small Lee pots, a large one would be better but I was kind of poor when setting up for casting. The Lee pots work well in spite of the leaking valve. I do prefer Lyman bullet molds over the Lee's but the Lees will work, be gentle, they are made of aluminum. The only time I tried hard led round balls in my muzzle loader it was bad, real bad. I found that pure soft lead was the only way to go, it may not matter in your revolver but it did with the patched ball. Enjoy.
pete2 is offline  
Old January 24, 2020, 07:59 PM   #8
David R
Senior Member
 
Join Date: January 2, 2015
Location: The swamps of WNY
Posts: 700
I had one. Get casting a few. Add more lead and instant slush. Wait.... wait, mild is cool , start over.

I had much better luck with a Coleman stove and a cast iron pot.

Just MY $.02.

David
David R is offline  
Old January 24, 2020, 08:56 PM   #9
DukeConnor
Senior Member
 
Join Date: May 6, 2016
Posts: 184
Don't be put off by the Lee haters. you can be very successful casting with Lee products Round balls should be cast with pure soft lead.
DukeConnor is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:33 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05169 seconds with 9 queries