May 10, 2013, 12:16 PM | #1 |
Senior Member
Join Date: March 2, 2013
Posts: 132
|
Cannelure on cases?
I have some 3-D remanufactured 38 Specials that I bought at a range about 20 years ago. I never paid attention back then, but now that I'm reloading, I noticed that some of the cases have circumferential grooves that look very similar to cannelures on bullets. They're knurled and some cases have 2 or 3, but most only have one or none. They're all different brands. Can anyone tell me why this was done and whether I should bother reloading them? Or whether I should be concerned at all? I'm worried that it would weaken the case.
|
May 10, 2013, 12:51 PM | #2 |
Senior Member
Join Date: January 6, 2011
Location: Thornton, Texas
Posts: 3,998
|
I personally have no idea why the lines/grooves are there, but since I have plenty of those cases (mostly in 38 special) and have reloaded them about a zillion times, it apparently isn't something to worry about. On the other hand, if it is something to worry about, maybe you and I will soon learn why from other folks.
|
May 10, 2013, 12:53 PM | #3 |
Senior Member
Join Date: September 22, 2011
Location: Middle America
Posts: 518
|
I've reloaded and shot many of .38 Spec brass with those canalures many time. I can't remember any case failures that I could contribute to them.
The 'makers' don't do anything that would cost more or take time with out reason. I just don't know what those reasons may have been. After the fact - reloads - it is a non event. Load with safety, OSOK |
May 10, 2013, 01:04 PM | #4 |
Senior Member
Join Date: October 28, 2006
Location: South Central Michigan...near
Posts: 6,501
|
There are some channelures that coincide with the base of the bullet in the case. If there are more than that one in that position, I suspect (but cannot prove), that it was used instead of a roll crimp on the mouth of the case for some reason.
|
May 10, 2013, 01:05 PM | #5 |
Senior Member
Join Date: April 23, 2006
Location: South Texas
Posts: 2,010
|
Yes, I'm going to ask the same question so that I can easily spot this thread. I've got them on 45 Colt, .357 and .38 and do not understand the reason they exist.
|
May 10, 2013, 01:05 PM | #6 |
Senior Member
Join Date: June 18, 2004
Location: Minden , Nebraska
Posts: 1,407
|
the grooves in the cases were there to prevent bullet set back. some companies did this and some didn't and even then only on some loads. how much of a problem in revolver rounds (or auto rounds for that matter) that really was or is now is probably open for debate.
|
May 10, 2013, 01:10 PM | #7 |
Senior Member
Join Date: October 14, 2009
Location: Sunshine and Keystone States
Posts: 4,461
|
IIRC the cannelures correspond to cases stamped as "wadcutters" and the cannelures may indeed correspond to the bottom of the wadcutter bullet when loaded. They may save the manufacturer a step in processing. However, those cases are identical in every other respect to standard .38 special cases and I have loaded them with non-wadcutter bullets, crimped as usual and never had a problem. I never crimp wadcutters that I press into any case, the long bearing area on the sides of the bullet and the mild loads are more than enough to hold them in place.
I can't recall seeing them on any cases other than .38 special, which also leads me to believe they are definitely wadcutter-related. |
May 10, 2013, 01:13 PM | #8 |
Senior Member
Join Date: March 2, 2013
Posts: 132
|
There seems to be no consistency in where they are located. They never seem to be closer together than about 1/4" to each other and not closer than 1/4" to the mouth or the base, but other than that, they're located all over.
|
May 10, 2013, 01:18 PM | #9 |
Senior Member
Join Date: March 2, 2013
Posts: 132
|
I just checked some from reloaded .357s that I got from my FIL. They had the grooves too. They were DE wadcutters, just like the 3-D, but reloaded by a friend of his.
|
May 11, 2013, 06:26 PM | #10 |
Senior Member
Join Date: December 1, 2002
Posts: 2,832
|
"Or whether I should be concerned at all? I'm worried that it would weaken the case."
No. And the cannalures won't weaken cases. |
May 11, 2013, 07:27 PM | #11 | |
Senior Member
Join Date: March 2, 2013
Posts: 132
|
Quote:
|
|
May 11, 2013, 07:33 PM | #12 |
Senior Member
Join Date: January 24, 2013
Location: NC
Posts: 545
|
I have loaded these type cases for many years without issue. I believe they are grip marks from tooling that needs them to retain the case in manufacturing processes.they don't line up with any bullets I have loaded.
|
May 11, 2013, 09:26 PM | #13 |
Senior Member
Join Date: May 26, 2000
Location: Hastings, Nebrasksa - the Hear
Posts: 2,209
|
Mostly bullet placement
In semi-automatic pistol rounds, the cannelure in the case kept the bullet from being seated deeper in the process of 1. getting slammed back and forth in the magazine, and 2. bumping up the feed ramp.
In revolver rounds, one can often see a cannelure at the base of the (original factory loaded) bullet. Why escapes me, as typically revolver bullets don't get seated deeper, but rather 'pulled' while the preceding rounds are being fired. I have seen some - older ammunition - where the cannelure appeared to be a form of crimping. Again, this applies only the original factory loading. Currently manufactured ammunition doesn't seem to have cannelures in the cases. At least not as much. As noted by others, I've reloaded cannelured and plain cases with no remarkable difference between the two categorical groups.
__________________
There ain't no free lunch, except Jesus. Archie Check out updated journal at http://oldmanmontgomery.wordpress.com/ |
May 11, 2013, 10:17 PM | #14 |
Senior Member
Join Date: March 20, 2013
Location: Benton, Arkansas
Posts: 120
|
Interesting. I've reloaded these as well. I've seen them way too far down the case for them to be associated with a seating depth.
|
May 12, 2013, 03:45 PM | #15 |
Senior Member
Join Date: September 22, 2011
Location: Middle America
Posts: 518
|
eldermike's got the best excuse so far. More plausible than anything I can think of.
Enjoy, OSOK |
May 12, 2013, 03:47 PM | #16 |
Senior Member
Join Date: May 29, 2011
Location: Fort Worth
Posts: 500
|
They showed up on different makes of ammo and were, as stated above, to stop bullet setback. I have GI 45 brass from several makers that have them also.
__________________
Education teaches you the rules, experience teaches you the exceptions (Plagiarized from Claude Clay) |
May 12, 2013, 05:33 PM | #17 |
Senior Member
Join Date: September 2, 2012
Location: N.central Pa.
Posts: 302
|
I have noticed them on a lot of the 9mm brass that I have accumulated also.
__________________
Gun control means: Being able to hit what you are shooting at. |
|
|