The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting > Bullet Casting

Reply
 
Thread Tools Search this Thread
Old September 14, 2020, 10:16 AM   #1
burbank_jung
Senior Member
 
Join Date: December 5, 2019
Posts: 472
Looking for a test

I'm did a quick search for cast rifle bullets with the front being pure lead and the base a hardcast and maybe water dropped. I've read one article of someone casting such a bullet but no results or photos of whether it works. Does anyone know of a source?
burbank_jung is offline  
Old September 14, 2020, 10:21 AM   #2
FrankenMauser
Senior Member
 
Join Date: August 25, 2008
Location: Potatoes and Hops
Posts: 12,496
I can't cite a source, but I've seen some reports on both sides.
Some say it's too much of a pain to be worthwhile, and the failure rate is very high.
Others say it works great.

There was at least one somewhat recent article (last year or so?) about doing such, in either Handloader or Successful Hunter magazine.
The author there used the two-mold method, where the nose is poured in its own mold. Then it is placed into the other mold, for the second alloy to be poured.
Photos looked good. Text of the article claimed it was the 8th wonder of the world.
I believe hogs were also used as ballistic test media.
__________________
Don't even try it. It's even worse than the internet would lead you to believe.
FrankenMauser is offline  
Old September 14, 2020, 12:04 PM   #3
burbank_jung
Senior Member
 
Join Date: December 5, 2019
Posts: 472
2 piece mold

I've seen images of the two piece molds and how the parts are suppose to be epoxied together. The most common methods I've read of are the hollow points and the softening the tip by submerging the base and shank in cold water and softening the tip with a propane torch. I think a pure lead buckshot at the tip and encased at the base with an alloyed lead/ GC would act like a softnose or like a paper patched bullet. It's something on my "want-to-do" list.
burbank_jung is offline  
Old September 24, 2020, 12:09 AM   #4
reloader28
Senior Member
 
Join Date: October 13, 2009
Location: nw wyoming
Posts: 1,050
I've played with them and am not that impressed. I think a pure lead nose with no jacket is just to soft to work the way I want.

For hunting, I much prefer the popular 50/50/2% alloy. Tho with these I like to water drop them to bring them to the about same hardness as my straight COWW bullets, then I anneal the front half. A little time consuming, but since I dont need many dedicated hunting bullets they last a long time and I've had great results with these in rifles
reloader28 is offline  
Old September 24, 2020, 11:55 AM   #5
burbank_jung
Senior Member
 
Join Date: December 5, 2019
Posts: 472
Yes, I've read about this annealing process. Thanks for replying.
burbank_jung is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:21 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2020 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.04525 seconds with 10 queries