|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
December 5, 2021, 11:41 AM | #1 |
Senior Member
Join Date: March 21, 2012
Location: Indianapolis, IN
Posts: 3,969
|
Need help downloading 223
I'm trying to do some ballistic gel testing for some hunting bullets with 223 to see what velocities they open up at. They are rated down to 1500fps want to see if they actually work at that speed. Not sure where to start. Hoping someone would have some guidance.
Currently have Cfe223 Bl-c2 Benchmark Big game Power pistol H110 Hp38 Aa#7
__________________
I don't believe in "range fodder" that is why I reload. Last edited by Shadow9mm; December 5, 2021 at 12:45 PM. |
December 5, 2021, 12:50 PM | #2 |
Senior Member
Join Date: November 27, 2009
Location: Zona
Posts: 423
|
I’ve used BlueDot and 800X with 40-50 grain bullets in the .223, not what you are looking for unfortunately. One issue you may have is bullet rpm. Your reduced loads will have about half the rpm of normal loads, meaning the forces on the bullet will be much less. This may impact how the bullet performs in the gel - bullet rpm reduces much more slowly than velocity does. Too, the reduced stability may cause bullet yaw and it may not impact the gel straight on.
The above is just theory, but something to consider. IME when a manufacturer says the bullet “expands” down to a certain velocity that usually means minimal expansion - maybe not even expanding past bullet diameter - so not usable expansion. It’s a good idea to test, although the best test would be at full hunting velocity and the test medium at the expected impact distance. .
__________________
.22LR - .223 - .22-250 - .243 - 6mm REM - .25-20 - .25-35 - .25 BB - .250/3000 - .257 WBY - .260 - .30 M1 - .300 BO - .30 Herrett - .300 Savage - .32 H&R - .303 - .338-06 - .338 WM - .35 REM - .38-55 - .45 LC - .45-70 - .50-70 |
December 5, 2021, 02:55 PM | #3 |
Staff
Join Date: March 11, 2006
Location: Upper US
Posts: 28,817
|
FOR COMPARISON ONLY
7gr of H110 under a 55gr bullet shows a muzzle velocity of 1900fps in the .22 HORNET You won't find low speed loads in standard .223 data, not because it can't be done, but because its not what most people are looking for, so the testers don't spend time and money doing those loads and putting them in the common data. So, if you're going to develop short range low speed loads, you are entirely on your own and "off the map" as it were.... I did, some 50 years ago create "gallery loads" in some rifle cases using pistol powder. These loads are "tricksy" and one screw up can result in a really bad accident. So, I will not recommend it, or give the details of what I did. I will say that a double, triple (or more) overcharge of pistol powder is difficult to spot in a large rifle case, and that can result in serious damage to your gun and even to you. So don't do that! Now, here's an alternate way of looking at it, go to a ballistic table and see what range your load is down to 1500fps. The 55gr Hornady SX bullet with a 3200fps muzzle velocity is down to about 1450fps at 500 yards, according to the table in their book. You could, if you have the range, set you ballistic gel at that distance, and shoot it with full power loads to see what the bullets actually do. Few people have that option. Or you can make a rational judgement about what you might shoot at that distance and how important expansion (and how much expansion) is required.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better. |
December 5, 2021, 06:51 PM | #4 | |
Senior Member
Join Date: March 21, 2012
Location: Indianapolis, IN
Posts: 3,969
|
Quote:
would working down with cfe223 be a bad idea? I know pressures will not be optimal, and it wont cycle the gun, just trying to figure if it would be safe for a few tests. not something I have any intention of doing regularly.
__________________
I don't believe in "range fodder" that is why I reload. |
|
December 5, 2021, 08:38 PM | #5 | |
Staff
Join Date: March 11, 2006
Location: Upper US
Posts: 28,817
|
Quote:
And, forget about reduced loads cycling any semi auto, unless you're willing to modify the gun specifically to do that. Very few guns, even ones with adjustable gas systems are adjustable enough to cover that range without some kind of modifications.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better. |
|
December 5, 2021, 09:01 PM | #6 | |
Senior Member
Join Date: March 21, 2012
Location: Indianapolis, IN
Posts: 3,969
|
Quote:
The problem is not tagging the block, but tagging it in the center of the block, and in line with the block so it stays in the block from end to end. With good loads my rifle will hold 1moa. So about 5in at 500. I would rather not take shots on game at that distance other than varmints, just curious to see if it would work. So in short I can tag the block, but no guarantee on a center shot. At 500 the bullet will be coming in from a pretty good angle. While I could calculate the trajectory and angle, and rig a mount to hold it at the right angle, if I can't tag it in the center and keep it in the block its a moot point. Thus trying to down load
__________________
I don't believe in "range fodder" that is why I reload. Last edited by Shadow9mm; December 5, 2021 at 09:36 PM. |
|
December 5, 2021, 10:05 PM | #7 |
Senior Member
Join Date: January 8, 2017
Location: Wilmington NC
Posts: 243
|
I load low power bottle neck rounds using pistol powder a lot.
I can run you some Quickload data, but you left out all of the needed details. Accuracy of calculated velocity is much better with:
I went ahead and ran a couple of powders (faster is better for this type of loading), a 55 gr Speer a random AOL & 16" barrel Code:
Cartridge : .223 Rem. (SAAMI) Bullet : .224, 55, Speer SP 1047 Useable Case Capaci: 26.819 grain H2O = 1.741 cm³ Cartridge O.A.L. L6: 2.260 inch = 57.40 mm Barrel Length : 16.0 inch = 406.4 mm Powder : Hodgdon HP38 Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time % % Grains fps ft.lbs psi psi % ms -30.0 20 4.20 1417 245 13128 2173 100.0 1.559 -26.7 21 4.40 1456 259 14067 2264 100.0 1.498 -23.3 22 4.60 1493 272 15023 2355 100.0 1.446 -20.0 23 4.80 1529 285 15998 2446 100.0 1.399 -16.7 24 5.00 1564 299 16992 2537 100.0 1.357 -13.3 25 5.20 1598 312 18005 2627 100.0 1.319 Cartridge : .223 Rem. (SAAMI) Bullet : .224, 55, Speer SP 1047 Useable Case Capaci: 26.819 grain H2O = 1.741 cm³ Cartridge O.A.L. L6: 2.260 inch = 57.40 mm Barrel Length : 16.0 inch = 406.4 mm Powder : Alliant POWER PISTOL Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time % % Grains fps ft.lbs psi psi % ms -12.0 22 4.40 1380 232 9482 2963 98.2 1.708 -08.0 23 4.60 1428 249 10144 3095 98.8 1.646 -04.0 24 4.80 1475 266 10829 3222 99.3 1.590 +00.0 25 5.00 1520 282 11535 3344 99.7 1.539 +04.0 27 5.20 1564 299 12263 3461 99.9 1.492 +08.0 28 5.40 1607 315 13014 3573 100.0 1.449 Code:
Cartridge : .223 Rem. (SAAMI) Bullet : .224, 55, Speer SP 1047 Useable Case Capaci: 26.819 grain H2O = 1.741 cm³ Cartridge O.A.L. L6: 2.260 inch = 57.40 mm Barrel Length : 22.0 inch = 558.8 mm Powder : Hodgdon HP38 Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time % % Grains fps ft.lbs psi psi % ms -33.3 19 4.00 1474 265 12206 1436 100.0 1.979 -30.0 20 4.20 1515 280 13128 1499 100.0 1.899 -26.7 21 4.40 1554 295 14067 1561 100.0 1.830 -23.3 22 4.60 1593 310 15023 1624 100.0 1.769 -20.0 23 4.80 1630 325 15998 1686 100.0 1.715 -16.7 24 5.00 1667 339 16992 1748 100.0 1.666 Last edited by P Flados; December 5, 2021 at 10:19 PM. |
December 6, 2021, 02:40 AM | #8 |
Staff
Join Date: March 11, 2006
Location: Upper US
Posts: 28,817
|
ok, I get it, its not hitting the block its hitting it center, point on and level. No, not simple. Forget I mentioned that,
__________________
All else being equal (and it almost never is) bigger bullets tend to work better. |
December 6, 2021, 05:40 AM | #9 |
Senior Member
Join Date: March 21, 2012
Location: Indianapolis, IN
Posts: 3,969
|
No worries
__________________
I don't believe in "range fodder" that is why I reload. |
December 6, 2021, 05:42 AM | #10 |
Senior Member
Join Date: March 21, 2012
Location: Indianapolis, IN
Posts: 3,969
|
Lehigh controlled chaos 55g. Solid copper. Bullet length .868. Col 2.245
__________________
I don't believe in "range fodder" that is why I reload. |
December 6, 2021, 10:40 AM | #11 |
Senior Member
Join Date: September 28, 2013
Posts: 3,815
|
You may consider using trailboss. But it may still be tricky to go down to 1500fps muzzle velocity with light .223 bullet, so some distance may still be needed.
-TL Sent from my SM-N960U using Tapatalk |
December 6, 2021, 11:39 AM | #12 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,060
|
If you can hit the center closely enough at 100 yards, and if we assume the BC from Lehigh is accurate at low velocities (it may not be), it looks like a muzzle velocity of about 1740 fps (drops to 1727 at 15 feet) would land going 1500 fps at 100 yards, which about 6.5 grains of Trail Boss should get you and it still gives you about 83% case fill at that load level (assumes a 24" barrel). However, having looked at a lot of Bryan Litz's BC measurements, I am not sanguine the claimed 0.278 BC will hold up at 1500 fps. It would be best, therefore, to use an optical chronograph set out at 100 yards to confirm impact velocity before setting up your ballistic medium.
The Miller stability estimator says you are probably going to need about an 8.5" twist to get reasonable stability at that low muzzle velocity with that long-for-weight bullet. The precision of that stability calculator with .224" bullets are limited, though, so if you work up to a Trail Boss load at about the velocity I mentioned when the chronograph is either on the muzzle or 15 feet out, you want to confirm first that the load groups well from your gun before setting the optical chronograph out at 100 yards. This is to be sure you aren't going to shoot it by mistake. Once you have a load you know groups and has about the right velocity, then shooting the center of the 6" square should not be a problem.
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
December 6, 2021, 12:02 PM | #13 |
Senior Member
Join Date: September 28, 2013
Posts: 3,815
|
Dropping the charge to 70% (still safe as per trailboss guideline) would get it close to 1500fps near muzzle. Shooting through an optical chrony at 100yd is pretty tricky and risky (of losing $200). Labradar would be handy.
-TL Sent from my SM-N960U using Tapatalk Last edited by tangolima; December 6, 2021 at 12:13 PM. |
December 6, 2021, 01:02 PM | #14 |
Senior Member
Join Date: March 21, 2012
Location: Indianapolis, IN
Posts: 3,969
|
Do have e a 1:7 twist so I should be good. Shooting at 100 makes sense. I do have an optical chronograph. It's been shot twice and survived. Would need to confirm zero then shoot over
__________________
I don't believe in "range fodder" that is why I reload. |
December 6, 2021, 02:13 PM | #15 |
Staff
Join Date: March 4, 2005
Location: Ohio
Posts: 21,060
|
Might be worth calling Hodgdon, too. The only Trail Boss load they list for 223 Rem is a 55-grain FMJ, and it shows a 4.0-grain maximum, which is below their own guidelines for minimum percent fill. I can't account for that.
__________________
Gunsite Orange Hat Family Member CMP Certified GSM Master Instructor NRA Certified Rifle Instructor NRA Benefactor Member and Golden Eagle |
December 6, 2021, 05:00 PM | #16 | |
Senior Member
Join Date: September 28, 2013
Posts: 3,815
|
Quote:
-TL Sent from my SM-N960U using Tapatalk |
|
December 6, 2021, 09:03 PM | #17 |
Senior Member
Join Date: November 30, 2014
Posts: 283
|
Hello, I have the answer, generally, in 20" barrel.
http://natoreloading.com/subsonic556/ About 6 grains of Blue Dot using 55 grain, or about 6.1 of AA#7. This is using 55 grain bullets. this will get you close if your using 20" barrel. Don't forget to shred up some cotton and put it in to hold the powder at primer end. P.S. the page is called subsonic, but since there was zero load data for those powders, it was all over the place. But enough was done to understand what load will get you close to subsonic, or 1500, or etc. |
December 7, 2021, 10:20 PM | #18 |
Senior Member
Join Date: January 8, 2017
Location: Wilmington NC
Posts: 243
|
Your bullet is not in QL, but a 62 gr is. I loaded the 62 gr, changed the weight and length and ran it.
Results were 15 to 20 fps faster than previous runs. |
December 7, 2021, 10:56 PM | #19 |
Senior Member
Join Date: March 21, 2012
Location: Indianapolis, IN
Posts: 3,969
|
Sounds good hoping to do some velocity testing Saturday. Weather permitting
__________________
I don't believe in "range fodder" that is why I reload. |
|
|