December 4, 2017, 01:30 AM | #1 |
Senior Member
Join Date: October 22, 2016
Posts: 3,883
|
Snider Enfield rifles
I think I asked about these a while back, but in a different section. Given how much I liked the responses I got in the Burnside thread, I figure I'll ask about these rifles here.
So, bottom line is the Snider's interest me and owning one is on my list along with a Burnside and maybe a Martini Henry for old black powder cartridge guns. The only difficulty I have in getting to own one of these is I have to buy them online and I don't like not being able to look them over in person because they are so old. So my question is: What should I look for and what questions should I ask the seller? I always ask about the bore, that's a standard question for every gun I have an interest in, but are there any things specific to the Sniders that are dealkillers? I won't ask about bullets because I think from all I've read and watched on reloading the Sniders is that round ball loads work best due to the slow twist.
__________________
"We always think there's gonna be more time... then it runs out."
|
December 4, 2017, 01:10 PM | #2 |
Senior Member
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
|
No round ball loads in a Snider. Although it's been done, it's not the best. A Snider is a BP cartridge rifle, not a muzzle loader. Uses .577 Snider ammo. It was sort of the Brit version of the TrapDoor Springfield. There was a Carbine version too. Fair number of 'em on the assorted auction sites at not totally stupid prices. Track of the Wolf sells brass. It uses a .570" lead bullet. Loaded ammo is expensive. Ten-X loads it periodically. Runs $89.99 per 20.
A Martini Henry is usually a .577/450. Ten-X loads it too at $99.99 per 20.(Have a .pdf how-to for making reloadable cartridges out of 3/4" brass bar stock if you ever want it. Uses a .460" bullet.) There was a .303 British variation too. Used by Canadian Militia up to W.W. I. Never seen one in decent condition though. Been looking for one for about 40 years now. Every time I see the movie 'Zulu'. snicker.
__________________
Spelling and grammar count! |
December 4, 2017, 04:12 PM | #3 |
Senior Member
Join Date: November 14, 2008
Posts: 355
|
Check-out IMA https://www.ima-usa.com/j if you're heading in that direction. But you probably already know that.
A few years ago I picked up an 1864 Snyder-Henry and a Mk IV 1885 Martini Enfield from them(both untouched). Wanted a cool winter project to bring life back to them. I have to say that maybe I was lucky but, after cleaning off all the YAK grease and grime, they turned out very well. Bores and chambers shined almost like new. Obviously they needed some wood repair but I wasn't disappointed with either one. Other than the obvious, what to look for in a Snyder would be the breach to barrel alignment, since that was a conversion from the original percussion guns. Last edited by springer99; December 5, 2017 at 03:40 PM. |
December 4, 2017, 04:28 PM | #4 |
Senior Member
Join Date: October 22, 2016
Posts: 3,883
|
^ What did you use to get all that crud off and how bad was the wood damage that needed fixing?
Basically, if I got one of these, would I be getting a safe and okay shooter? https://www.ima-usa.com/collections/...ched-condition EDIT: I think I'd rather get one that they've cleaned themselves and have it hand selected. I just read through what the untouched ones may not have and firing pins was one of them. No, I want to shoot these, so firing pins are a necessity.
__________________
"We always think there's gonna be more time... then it runs out."
Last edited by TruthTellers; December 4, 2017 at 04:40 PM. |
December 4, 2017, 08:51 PM | #5 |
Senior Member
Join Date: July 3, 2005
Location: Alabama
Posts: 925
|
I purchased a cleaned and complete from them and I am happy with it. I shoot 24ga plastic shotgun hulls trimmed down to correct length and .60 round pure lead balls. I load the hulls with 2F Goex black powder.
TK |
December 4, 2017, 10:44 PM | #6 | |
Senior Member
Join Date: November 14, 2008
Posts: 355
|
Quote:
If you speak with to them, I'm sure they'd tell you that the best chance of getting a good shooter would be with the Mk IV Martini's as they're all original British made. The majority of the Snyders(unless you're extremely lucky) were modified from 1853 percussion Enfields in Nepal. |
|
December 4, 2017, 10:54 PM | #7 |
Senior Member
Join Date: November 14, 2008
Posts: 355
|
Nice looking Snyder there. Mined turned out about the same. Did you grease those .60cal balls with anything special or just thumb press them into the hulls.
|
December 4, 2017, 11:02 PM | #8 | |
Senior Member
Join Date: October 22, 2016
Posts: 3,883
|
Quote:
Most Snyder's were made in Nepal? That's just something I'll have to live with. As long as it can shoot and isn't rusted and has a decent bore, that's all I ask for from such old rifles.
__________________
"We always think there's gonna be more time... then it runs out."
|
|
December 5, 2017, 02:29 PM | #9 |
Senior Member
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
|
"...Most Snyder's were made in Nepal?..." Nope. London Small Arms Company and the Birmingham Small Arms Co. made and converted 'em. Lot of 'em copied in Nepal though.
It's Snider, not Synder.
__________________
Spelling and grammar count! |
December 5, 2017, 02:47 PM | #10 |
Senior Member
Join Date: October 22, 2016
Posts: 3,883
|
If I were to spend my mostly hard earned money on a Snider, would I be going the wrong way if I bought a Nepalese one over an English one? What would the price difference be between a Nepalese Snider over an English Snider?
__________________
"We always think there's gonna be more time... then it runs out."
|
December 5, 2017, 10:31 PM | #11 |
Senior Member
Join Date: July 3, 2005
Location: Alabama
Posts: 925
|
|
December 6, 2017, 12:24 AM | #12 |
Senior Member
Join Date: November 14, 2008
Posts: 355
|
Doubt that that would be a wrong way, but not sure it's a better one either. Since I got my Snider about 6 years ago, I've only ever seen one British marked one. It was priced just about what one pays for a restored Nepal one today and in about the same condition. They do show up from time to time, especially coming from Canada. My guess is that the demand for British or other European military arms just don't command much interest on this side of the pond. In one respect, that's good for those that just appreciate the history of military arms. Take advantage of that if that's your bent.
|
December 6, 2017, 12:26 AM | #13 |
Senior Member
Join Date: November 14, 2008
Posts: 355
|
|
December 6, 2017, 01:27 AM | #14 | |
Senior Member
Join Date: October 22, 2016
Posts: 3,883
|
Quote:
Also have an interest in Russian military arms of the early 20th Century, but that's a different topic.
__________________
"We always think there's gonna be more time... then it runs out."
|
|
December 6, 2017, 10:13 AM | #15 | |
Senior Member
Join Date: November 14, 2008
Posts: 355
|
Quote:
|
|
December 6, 2017, 01:25 PM | #16 | |
Senior Member
Join Date: October 22, 2016
Posts: 3,883
|
Quote:
I buy guns to be shooters, not safe queens. That's why I asked if I could go wrong with a Nepalese Snider over an English one. If the Nepalese rifles are good shooters that, if taken care of, will last me a decade or more, I'll be perfectly happy.
__________________
"We always think there's gonna be more time... then it runs out."
|
|
December 6, 2017, 01:58 PM | #17 |
Senior Member
Join Date: February 13, 2002
Location: Canada
Posts: 12,453
|
"...especially coming from Canada..." Ours came from The Old Country. At that time there was nobody making firearms here. Our government went crying to the Colonial Office for rifles to deal with the Fenian Raids(1866 to 1871) from the U.S.
"...difference be between a..." QC and metallurgy, but the Nepalese rifles are supposedly very well made just the same. There are likely some Afghan Village Smithy Sniders around too. Those are 100% hand made out of whatever materials were found locally. The thing with collecting vs having a shooter is trying to have an example of all of 'em. "...back to the '60's..." There was probably still milsurp ammo around, but not common. You can get or make either .43 fairly easily now.
__________________
Spelling and grammar count! |
December 16, 2017, 09:52 AM | #18 |
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,829
|
I'm concerned about lockup.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
December 17, 2017, 10:28 PM | #19 |
Member In Memoriam
Join Date: March 17, 1999
Posts: 24,383
|
The Snider action is pretty sturdy and since it swings open to the side (unlike the "trapdoor" Springfield) the pressure is straight back into the standing breech.
But unless one is, for some reason, interested in Nepalese weapons manufacturing, I would strongly suggest acquiring a gun made in England. Guns made in areas like Nepal and India tend to be well finished and look good, but the metal may be soft and not durable. (The British needed a native armed force to be called on in an emergency or for show; they did not need a native force armed with high quality, durable weapons that might be turned against them.) Jim |
December 18, 2017, 03:25 PM | #20 |
Senior Member
Join Date: October 22, 2016
Posts: 3,883
|
Given how many of these rifles were conversions of rifle muskets, I don't think there's going to be much difference in steel quality between English or Nepalese Sniders.
__________________
"We always think there's gonna be more time... then it runs out."
|
January 1, 2018, 05:50 PM | #21 |
Member
Join Date: March 24, 2013
Posts: 33
|
You can find nearly everything there is to know about Sniders on the British Militaria Forums, Snider sub forum. Shooting, reloading, values, variations, info on where to buy etc are all throughly covered. In addition, You Tube has a number of videos on reloading for this Beast. Same is true with Martini Henry and other old British guns which are all featured on this website. .577 Snider is my ultimate cartridge. Have fun!
Seamus |
March 16, 2018, 07:55 PM | #22 |
Senior Member
Join Date: October 22, 2016
Posts: 3,883
|
I have a lead on a cavalry Snider rifle with a 20 inch barrel in superb condition. My question is how common were the shorter cavalry Snider's compared to standard ones?
Also, for shooting, how much of a loss in velocity can I expect going from a 36 inch barrel to a 20 inch?
__________________
"We always think there's gonna be more time... then it runs out."
|
March 26, 2018, 02:11 PM | #23 |
Staff
Join Date: November 2, 1998
Location: Colorado
Posts: 21,829
|
BTW, I'd use conicals instead of round balls. The P53 Enfields they were based on shot conicals.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe! |
March 26, 2018, 09:06 PM | #24 |
Senior Member
Join Date: July 3, 2005
Location: Alabama
Posts: 925
|
The Nepalese bores are larger and the .590 RB works well. On an British made rifle the .577 Minie should work fine. Pays to test to see as some British rifles have larger bores too.
|
Thread Tools | Search this Thread |
|
|