The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Semi-automatic Forum

Reply
 
Thread Tools Search this Thread
Old September 14, 2018, 11:30 AM   #1
shickelgruber
Junior Member
 
Join Date: January 6, 2012
Location: cincinnati,ohio
Posts: 5
Magazine drops out!

I have a Ruger MK111 hunter ,installed all of the Volquartsen upgrades,has as sweet trigger pull, everything works great,except the magazine falls out,gos in with a click, cant figure it out! Tried to contact Volquartsen two times,in two weeks,left messages,never returned my calls,got any ideas?
shickelgruber is offline  
Old September 14, 2018, 02:37 PM   #2
tipoc
Senior Member
 
Join Date: December 11, 2004
Location: Redwood City, Ca.
Posts: 3,546
Why would your trigger upgrades effect the mag staying in place? Are you confident that the trigger work is the issue?

tipoc
__________________
1. All guns are always loaded.
2. Never let the muzzle cover anything you are not willing to destroy.
3. Keep your finger off the trigger till you are ready to shoot.
4. Identify your target and know what is beyond it.
tipoc is offline  
Old September 14, 2018, 06:47 PM   #3
cw308
Senior Member
 
Join Date: September 2, 2010
Location: Plainview , Long Island NY
Posts: 2,723
There isn't much going on with the release , did you remove or clean the release , was it working before the upgrades , is the opposite side of the release button even with the frame when magazine is locked in place? How does the notch look on the magazine where it locks in place ?
cw308 is offline  
Old September 14, 2018, 07:18 PM   #4
BlackDuck
Junior Member
 
Join Date: September 9, 2018
Posts: 9
I would go with cw308 and look at the notch - it should be facing the hold down screw. Other than that, may have not gotten the spring in properly when you reassembled it.
BlackDuck is offline  
Old September 14, 2018, 11:40 PM   #5
Troy800
Senior Member
 
Join Date: December 25, 2015
Posts: 100
Did you install the magazine ejector upgrade, I would start there if you did. It Has been a few years since I did all the upgrades to mine. I did all volquartsen upgrades to mine except the hammer bushing. I used a Tandemkross hammer bushing for to remove the magazine disconnect. Don't remember exactly why but do remember some discussions on the Volquartsen hammer bushing for the mk3 and magazine disconnect. The Tandemkross hammer bushing had better reviews for removing magazine disconnect. May want to research the hammer bushing.
Troy800 is offline  
Old September 16, 2018, 09:04 PM   #6
shickelgruber
Junior Member
 
Join Date: January 6, 2012
Location: cincinnati,ohio
Posts: 5
Mag dropout.

Thanks for the input, I will get back,
shickelgruber is offline  
Old September 17, 2018, 12:19 PM   #7
T. O'Heir
Senior Member
 
Join Date: February 13, 2002
Location: Canada
Posts: 10,129
"...installed all of the Volquartsen upgrades..." If there was no issue prior to doing that, obviously, one of 'em is installed incorrectly. I'd be guessing it's probably the extended mag release. All those wee parts require fitting too.
__________________
Spelling and grammar count!
T. O'Heir is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:25 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2018 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05154 seconds with 9 queries