June 22, 2017, 11:32 AM | #1 |
Senior Member
Join Date: June 22, 2017
Posts: 1,011
|
5.7mm Johnson
I recently joined The Firing Line, so apart from my Introduction post, this is my first time posting here.
I have a Plainfield/Iver-Johnson Carbine chambered in 5.7mm Johnson (a/k/a 22 Spitfire) which is simply a 30 Carbine case necked down to 22. I have been attempting to load for it since I bought it in 1983.
I would like to know if there is anyone here who has any experience with the cartridge that can help me work out what I'm doing wrong with my load. Any help would be appreciated. Thank you. |
June 22, 2017, 01:09 PM | #2 |
Senior Member
Join Date: November 13, 2006
Posts: 8,283
|
I don't know what is going on.I have no experience with the 5.7.
Seems like you have been quite thorough. My hunch,odds are your old load data may be out of date.DuPont is not making powder.The Hogdon surplus powder is gone. A lot of the same powder names are still in use,but that powder is made by different folks at a different facility using different processes and maybe a different recipe. Published charge weights today are not the same as they were in the day of the 5.7. I don't know the exact safe pressure for the M1 Carbine.Its not full modern bolt action.Its someplace in the 40 k's ,probably CUP. What pressure signs are you seeing? More to the point,is it about strength,or how the gas system is responding? Last edited by HiBC; June 22, 2017 at 01:14 PM. |
June 22, 2017, 01:20 PM | #3 | |||
Senior Member
Join Date: June 22, 2017
Posts: 1,011
|
Quote:
Quote:
Quote:
|
|||
June 22, 2017, 01:20 PM | #4 |
Senior Member
Join Date: April 10, 2008
Location: Alaska
Posts: 7,014
|
See if you can get some quick load data run (ok once in a while)
You can just use less powder as well. |
June 22, 2017, 05:53 PM | #5 | |
Senior Member
Join Date: June 22, 2017
Posts: 1,011
|
Quote:
|
|
June 22, 2017, 07:43 PM | #6 |
Senior Member
Join Date: August 7, 2009
Posts: 214
|
wdwhit, I would love to start reloading for this guy also !! were is the 1st place to you started looking for info! I do have the dies and brass.This 5.7 j has
been sleeping to long ! |
June 22, 2017, 08:07 PM | #7 |
Senior Member
Join Date: November 13, 2006
Posts: 8,283
|
Once again,I know nothing about the 5.7.
You are using what might be called slow pistol powders,good for the 30 Carbine. There is quite a difference in expansion ratio between the straight sided carbine case and the necked down 22. A cartridge like the 221 Fireball IS NOT interchangeable,but it might give you some leads toward a more ideal powder choice. So might the 22 Hornet and 218 Bee. Some of the lower vel .222 benchrest loads might also suggest powders. Myself,I'd look to slower,more "rifle" powders and then sneak up on chrono'd.not estimated,5.7 velocities. I take primer reads as worth watching,as part of the total picture. But brass extrusion into the ejector is a pretty definitive "Whoa!" A wild guess,a powder like Benchmark might be worth a try. Last edited by HiBC; June 22, 2017 at 08:15 PM. |
June 22, 2017, 10:50 PM | #8 | |
Senior Member
Join Date: June 22, 2017
Posts: 1,011
|
Quote:
In addition, I have compiled a fairly large body of empirical knowledge from my attempts to load and fire hundreds of rounds. |
|
June 22, 2017, 11:11 PM | #9 | |
Senior Member
Join Date: June 22, 2017
Posts: 1,011
|
Quote:
I also tried Hercules 2400 and IMR-4198. The results from 2400 were comparable to IMR-4227. I could not come up with an IMR-4198 load that would reliably cycle the action so I did not move on to "slower" powders. It has been suggested that among more recent powders, Accurate 5744 or Accurate 1680 might fit in the gap between IMR-4227 and IMR-4198 and do the trick. |
|
June 22, 2017, 11:13 PM | #10 | |
Senior Member
Join Date: June 22, 2017
Posts: 1,011
|
Quote:
|
|
June 23, 2017, 10:04 PM | #11 |
Senior Member
Join Date: January 24, 2011
Posts: 1,427
|
What primers are you using? I ask because back then Fed. 200 primers were listed in Hornady 4 AND by Fed. themselves as Pistol Mag. & small rifle. In 30 Carb. applications I ran into flat primers with start loads of H110 / W296. I switched to CCI and Win. and no flat primers.
If your load data is with Fed. 200 primers either change out to 205's or another small rifle primer. |
June 24, 2017, 01:20 PM | #12 | |
Senior Member
Join Date: June 22, 2017
Posts: 1,011
|
Quote:
I can no longer easily get CCI primers locally, so I have switched to Winchester Small Rifle (WSR) primers. But, I still have 80+ rounds of formed, sized and primed brass primed with the CCI primers to use up before I get into the Winchester stash. |
|
June 24, 2017, 01:42 PM | #13 | |
Senior Member
Join Date: June 22, 2017
Posts: 1,011
|
Quote:
Also, do you currently have a 5.7mm Johnson rifle? If so, was a commercial rifle purpose built as a 5.7 or was it an M1 Carbine that was converted? If converted, who did the work? I ask because while it would seem that all that is necessary to make the conversion is to yank off the 30 Caliber barrel and spin on a 22 Caliber barrel, the fact the 5.7mm is a bottleneck cartridge with a pointy bullet as opposed to the round nose of the 30 Carbine means that converted rifles can have feeding problems with the rounds hanging up on the lip of the receiver if a feed ramp was not either soldered in place or built up out of brazing material by the company/gunsmith doing the conversion. Also, there is some inconsistency in the barrels used by various manufacturers. Some actually have a 0.2230 bore. Others are 0.2240. The Johnson ones apparently had a bore somewhere around 0.2235. If you're asking the cartridge to not only propel the bullet down the barrel, but also "swage" it to a smaller diameter in the process, that can raise chamber pressures and affect performance. You may want to have your chamber and bore case by a gunsmith (or do it yourself with Cerrosafe that you can get from Midway or several other sellers) to be sure. Be aware that Cerrosafe changes dimensions over the course of a few hours after it is cast, so you want to be ready to make your measurements as soon as you do the cast. If your bore is 0.2230 or 0.2235, Sierra still makes 40 and 45 grain bullets in 0.2230 diameter that you can use. Check neck tension if you are using 0.2230 bullets as many reloading dies are supplied with expanders intended for use with 0.2240 bullets. You may need to contact your die maker and have them supply an expander plug for 0.2230 bullets. RCBS did not charge me for this. |
|
June 24, 2017, 01:52 PM | #14 |
Senior Member
Join Date: June 22, 2017
Posts: 1,011
|
I want to thank everyone who contributed their experience and ideas to answering my question. I am still oping to find someone who is successfully reloading the cartridge and can share that experience with me.
On other forums, I have found only four other people who admit to having attempted to load for the cartridge and none of them appear to be currently doing so. The heyday of the Carbine in civilian hands was in the 1960's. The 5.7 was only made by a few manufacturers/converters most doing their work in the 1960's and 1970's with the last being done in the late 1980's. Given that was now four decades ago, I suspect that most of the people who owned the guns and loaded for them have passed away or gotten so old that they don't venture on-line and that their heirs have no idea what to do with the rifles or the reloading equipment. I don't like to think that I may be the last dinosaur walking around trying to make this cartridge work, but if I am, so be it. I will hope in the end to at least make sure that the last 5.7mm Johnson rounds made are well-crafted. |
June 24, 2017, 10:58 PM | #15 |
Senior Member
Join Date: August 7, 2009
Posts: 214
|
mine was a conversion off a quality hmc carbine, with a nice aftermarket stock .I don't know when It was done .It was giving to me as a gift and they thought it was a basic 30 carbine.I only found out when I was trying to shoot it and the round wouldn't chamber .
|
June 24, 2017, 11:29 PM | #16 | |
Senior Member
Join Date: June 22, 2017
Posts: 1,011
|
Quote:
Second, I can only imagine how you felt as the fact you had a wildcat cartridge on your hands dawned on you. After all, I went out looking for the rifle while you had it thrust upon you. Third, congratulations on being bold enough to rise to the challenge! Do you know for sure what the barrel diameter is? As noted in my previous post, it could be 0.2230, 0.2240 or anything in between. |
|
|
|