The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools Search this Thread
Old September 21, 2022, 09:56 PM   #1
akinswi
Senior Member
 
Join Date: October 14, 2012
Location: Bowling Green, Ky
Posts: 536
M1 Garand GI Front Sight

Is there a good method I can use to evenly file down the front sight ? I am trying to get back 5 to 6 clicks of elevation. I bought an after market GI sight as not ruin the original

Im assuming I could apply some light cold bluing after im done

Thanks
akinswi is online now  
Old September 21, 2022, 10:49 PM   #2
tangolima
Senior Member
 
Join Date: September 28, 2013
Posts: 2,822
Even on the top of the front sight post?

Just eyeball it looking through the peep sight. It is even when it looks even to you.

My 2 M1s have 9 clicks up for 100yd zero with my own handload. I will have to file the front sight down by 0.025" to bring it down to 5 clicks. Naw too much work. I leave them alone.

Matte black is the best color for sight. Blackening with candle soot is the old school method. I just use the cheap spray paint from home Depot. Make a mask by poking a hole in a piece of paper to cover the other parts of the rifle. A squirt or two will do. It works better if the sight post is degreased first.

-TL

Sent from my SM-N960U using Tapatalk
tangolima is offline  
Old September 25, 2022, 08:46 AM   #3
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 21,585
Scribe a line front and back. Got a stone that fits between the two blades? Put sight upside down and on the stone and push. Stone may be mounted in a vise to keep it stable.

I'd rather put it in a milling machine and do it with precision.
__________________
Vigilantibus et non dormientibus jura subveniunt. Molon Labe!
4V50 Gary is offline  
Old September 25, 2022, 05:47 PM   #4
jcj54
Senior Member
 
Join Date: February 28, 2011
Posts: 162
Cutting down the front sight

Remember that the with M1 sight radius .008" equals 1 MOA, so 5--6 clicks would take. 040" to .048" of metal removal.
jcj54 is offline  
Old October 3, 2022, 08:58 AM   #5
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 20,210
You could probably find either a mill file or a square jeweler's file near or a little over the width of the sight post and sandwich it between two tongue depressors in a vice so that the edges of the tongue depressors stuck out an eighth of an inch or so above the filing edge to keep the post on track while stroking the sight toward the file handle. You'd still have to keep the inverted sight base parallel to the vice jaws by feel, but it is doable.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Benefactor Member and Golden Eagle
Unclenick is offline  
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:13 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2022, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2021 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.03393 seconds with 10 queries