The Firing Line Forums

Go Back   The Firing Line Forums > Hogan's Alley > Handguns: The Revolver Forum

Reply
 
Thread Tools Search this Thread
Old October 12, 2009, 01:20 PM   #1976
CraCZ
Member
 
Join Date: August 11, 2006
Location: tucson
Posts: 56
Flyfish could you please help me date this m19-3. ser#4k26xxx Thanks for any help-ken
CraCZ is offline  
Old October 12, 2009, 01:48 PM   #1977
Pensrollei
Junior Member
 
Join Date: October 12, 2009
Location: Augusta, Ga
Posts: 3
I am new too. I need help

I purchased a Smith & Wesson Model 10-5 Serial Number D370XXX with a 4" barrel. I would like to find answers to 3 questions:

1: About what year was this gun made?

2: Can it handle the +P+ ammunition?

3: Should the firing pin wiggle some in the hammer or should it be tight?

Thanks for any response: In Georgia
Pensrollei is offline  
Old October 12, 2009, 03:24 PM   #1978
FlyFish
Senior Member
 
Join Date: January 20, 2009
Location: Overlooking the Baker River Valley
Posts: 1,727
CraCZ: Your 19-3 dates from 1973.

Pensrollei: 1. 1971-72. 2. I wouldn't fire +P+ ammo in any of my guns as it doesn't necessarily meet SAAMI specs for peak pressure, but that's me. I don't think your Model 10 is going to kaboom if you try it, but I still wouldn't recommend it. If you want another opinion, you could call S&W - my guess is they'll tell you the same (and you might get some other opinions here as well). 3. The firing pin is designed to pivot up/down but shouldn't have much movement at all side to side.
FlyFish is offline  
Old October 12, 2009, 04:35 PM   #1979
Hersir
Junior Member
 
Join Date: November 15, 2008
Posts: 1
Dating a pair of S&W Model 60 snubbies

I recently obtained a pair of S&W Model 60 stainless steel snubbies in .38 Special. The serial numbers are R665xx and BBF07xx. Can anyone give me an idea of when these two revolvers were manufactured? Many thanks.
Hersir is offline  
Old October 12, 2009, 04:53 PM   #1980
carguychris
Senior Member
 
Join Date: October 20, 2007
Location: Richardson, TX
Posts: 7,523
Quote:
I purchased a Smith & Wesson Model 10-5 Serial Number D370XXX with a 4" barrel... Can it handle the +P+ ammunition?
If it's one of the rare Model 10's chambered from the factory in .357 Magnum, yes. Such a Model 10 will say ".357 MAGNUM" on the side of the barrel and will readily chamber a .357 Magnum cartridge.

If not, NO. It is a gun-destroying kB! looking for an opportunity to happen.

Some commercial +P+ is loaded to near-.357Mag pressure levels, nearly double .38Spl pressure levels. The only factory S&W revolvers chambered in .38Spl that are generally strong enough to handle it are N frame .38/44s, which are ridiculously overbuilt; however, even then, I'd be hesitant to fire it through one of these rare and valuable collector's items.

OTOH +P (without the "+" suffix) is safe in most postwar steel-frame .38Spl S&W revolvers, including your Model 10.
carguychris is offline  
Old October 12, 2009, 04:59 PM   #1981
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
I recently obtained a pair of S&W Model 60 stainless steel snubbies in .38 Special. The serial numbers are R665xx and BBF07xx.
R665XX = between 1970 to 1973.
BBF07XX = 1988.

Jim
laytonj1 is offline  
Old October 12, 2009, 05:01 PM   #1982
tyusclan
Member
 
Join Date: August 17, 2009
Location: Florida
Posts: 45
Hersir- R665xx should be ~ early 1973.

The BBF prefix is July 1988.

Any S&W manufactured after 1957 when model numbers were assigned can handle +p ammunition with no problem.
tyusclan is offline  
Old October 12, 2009, 06:00 PM   #1983
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
R665xx should be ~ early 1973
Tyusclan,

Curious, but the SCSW shows R30001 to R99999 running 1970 to 1973. What source are you using to get "early 1973"?

Jim
laytonj1 is offline  
Old October 12, 2009, 06:43 PM   #1984
tyusclan
Member
 
Join Date: August 17, 2009
Location: Florida
Posts: 45
Strictly a guess, and I probably shouldn't do that. My apologies.

You're exactly right on the serial # and year range given.
tyusclan is offline  
Old October 12, 2009, 08:59 PM   #1985
duramax
Junior Member
 
Join Date: October 12, 2009
Location: Left Coast Calie
Posts: 1
Highway Patrolman

Please would like to know when this was made S&W Highway Patrolman 4" s/n S2758xx Thanks//K
duramax is offline  
Old October 12, 2009, 09:33 PM   #1986
sinister1811
Member
 
Join Date: July 20, 2005
Posts: 51
Hey guys. Just came into a S&W model 25-2, serial # N734247. What is the date of manufacture and approximate value of this gun in good condition. Thanks
sinister1811 is offline  
Old October 12, 2009, 09:49 PM   #1987
tyusclan
Member
 
Join Date: August 17, 2009
Location: Florida
Posts: 45
duramax- 1966-1967

sinister1811- 1980. The book shows good condition at $335, very good at $400.
tyusclan is offline  
Old October 12, 2009, 10:36 PM   #1988
jakeeee
Junior Member
 
Join Date: October 12, 2009
Posts: 5
hey Jim i would appreciate a little help i have been holding on to an old .38 (i think)for a few years now.i'm sure its not worth any money value...i would like to find parts for it though......the sn is 508690 no letters are before it
help would be awesome
jakeeee is offline  
Old October 12, 2009, 10:41 PM   #1989
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
hey Jim i would appreciate a little help i have been holding on to an old .38 (i think)for a few years now.i'm sure its not worth any money value...i would like to find parts for it though......the sn is 508690 no letters are before it
5 shot or 6? Swing out cylinder? 38 S&W or 38 S&W Special (Spl)?

Jim
laytonj1 is offline  
Old October 12, 2009, 11:20 PM   #1990
jakeeee
Junior Member
 
Join Date: October 12, 2009
Posts: 5
5 shot.i don't know gun lingo.it opens forward
jakeeee is offline  
Old October 12, 2009, 11:27 PM   #1991
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Quote:
5 shot.i don't know gun lingo.it opens forward
By opens forward do you mean the Barrel and cylinder hinges downward when opened?

Jim
laytonj1 is offline  
Old October 12, 2009, 11:28 PM   #1992
jakeeee
Junior Member
 
Join Date: October 12, 2009
Posts: 5
yes....and that pin is the piece i'm missing so its in two parts
jakeeee is offline  
Old October 12, 2009, 11:31 PM   #1993
jakeeee
Junior Member
 
Join Date: October 12, 2009
Posts: 5
it looks very similiar to the pics on the top of page 33 of these posts
jakeeee is offline  
Old October 12, 2009, 11:42 PM   #1994
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
Then with a serial number of 508690 it would be a .38 Double Action 4th Change made from 1895 to 1909 and look like this:

For parts, try starting here:
http://www.e-gunparts.com/productsch...ION%20REVOLVER

Jim
laytonj1 is offline  
Old October 12, 2009, 11:47 PM   #1995
jakeeee
Junior Member
 
Join Date: October 12, 2009
Posts: 5
thanks alot it looks like that but the barrel seems shorter...before i start taking the rust off its not a rare model or special right?
jakeeee is offline  
Old October 12, 2009, 11:52 PM   #1996
laytonj1
Senior Member
 
Join Date: June 1, 2005
Posts: 4,443
If you look at the parts link I posted under the picture you can get barrels in 3, 4, 5 and 6".
Value's not that high... especially if your're removing rust.

Jim
laytonj1 is offline  
Old October 13, 2009, 07:08 AM   #1997
hotcha45
Member
 
Join Date: March 22, 2009
Posts: 96
Model 60

The Model 60 I posted to ask about all the stamps I would guess is fairly late in Model 60 no-dash production - S/N R246xxx from the 6 digit number. I was assuming it was stainless - glad to have that confirmed.
hotcha45 is offline  
Old October 13, 2009, 08:25 AM   #1998
carguychris
Senior Member
 
Join Date: October 20, 2007
Location: Richardson, TX
Posts: 7,523
Quote:
sinister1811- 1980. The book shows good condition at $335, very good at $400.
The book value is about 2/3 of what a M25-2 would sell for around here.
carguychris is offline  
Old October 13, 2009, 10:38 AM   #1999
Pensrollei
Junior Member
 
Join Date: October 12, 2009
Location: Augusta, Ga
Posts: 3
I appreciate the responses from FlyFish and CarGuyChris. As I said, I am new and do not know the difference between +P and +P+. I will look the up. Stupid question, but does 38 Smith & Wesson Special CTG on the barrel stand for cartridge?
Pensrollei is offline  
Old October 13, 2009, 10:49 AM   #2000
Jeff #111
Senior Member
 
Join Date: July 25, 2001
Location: Idaho
Posts: 1,074
Pensrollei
Quote:
I appreciate the responses from FlyFish and CarGuyChris. As I said, I am new and do not know the difference between +P and +P+. I will look the up. Stupid question, but does 38 Smith & Wesson Special CTG on the barrel stand for cartridge?
Yes.

+P and +P+ indicate 38 Special loads that are above the industry pressure standards for the standard 38 Special load. The +P+ is a very high velocity load and resembles a "light" .357 magnum load in terms of pressure and ballistics. You do not shoot +P+ 38 special loads in anything, but a .357 magnum revolver or one of the old Smith & Wesson Heavy Duty and Outdoorsman revolvers (1930-1966). The danger with +P+ 38 Special is that they will chamber in a standard 38 special revolver but they are designed to be fired in a .357 magnum revolver.

The 38 +P+ load used to be called the 38/44, 38 Super Police and the 38 High Velocity. The Heavy Duty revolver and the 38/44 load were introduced together. I own both and I have a few hundred +P+ 38 special rounds. However I won't shoot those in my Heavy Duty and Outdoorsman revolvers because they are collector items and cost me some money.

However I do shoot +P+ in my Ruger GP100 revolver all the time. No danger there.

If you want to know more about the Heavy Duty and the 38 High Velocity/ +P+/ Super Police/ 38/44 HV go to this website. It's run by a collector of Heavy Duty revolvers and the last page will provide some history.


http://www.38-44heavyduty.com/

Last edited by Jeff #111; October 13, 2009 at 10:59 AM. Reason: Additional info
Jeff #111 is offline  
Reply

Tags
s&w 686

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:17 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2024 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Page generated in 0.65204 seconds with 9 queries